1000 мануал по эксплуатации - Arganabio.ru - инструкции по эксплуатации и многое другое

Настоящее руководство по эксплуатации (РЭ) предназначено для изучения конструкции, технических характеристик, правил эксплуатации контроллера (регулятора температуры) STC-1000 (в дальнейшем по тексту – «прибора»).

Перед установкой прибора в объект регулирования необходимо внимательно ознакомиться с настоящим РЭ.

Прибор рекомендуется эксплуатировать при температуре окружающего воздуха от минус 10 до плюс 60°С, относительной влажности (45–85)%.

1 Назначение.

Контроллер (регулятор температуры) STC-1000 предназначен для контроля и поддержания температуры объектов эксплуатации производственно-технического и бытового назначения. Прибор имеет два реле и может управлять одновременно нагревателем и холодильником.

В качестве датчика температуры используется NTC термистор длиной присоединительного кабеля 1 м. Датчик температуры входит в комплект поставки прибора.

2 Технические характеристики

2.1 Питание от сети перемененного тока напряжением 110 — 220В, 50 Гц.

2.2 Диапазон регулирования температуры (задания уставки) от минус 50 до плюс 99°С.

2.3 Разрешающая способность измерения температуры и задания уставки 0,1°С.

2.4 Возможность юстировки контроллера с дискретностью 0,1°С.

2.5 Диапазон задания температурного гистерезиса (разницы между температурой выключения и температурой включения реле) – от 0,3 до 10°С.

2.6 Время задержки включения реле «Cooling» (холодильника) – от 0 до 10 мин.

2.7 Максимальные коммутируемые токи реле – 8 А (максимальная мощность нагрузки – 1,5 кВт при 220 В 50Гц и cos j ³ 0,6).

Габаритные размеры 75х35х85 мм.

3 Указания мер безопасности

3.1 Внимание! В приборе используется напряжение питания опасное для жизни человека.

3.2 Все подключения, а также техническое обслуживание и ремонт необходимо осуществлять при отключенной сети.

3.3 Установка, подключение прибора к сети и нагрузке должны производиться только квалифицированными специалистами, изучившими настоящее РЭ. Все соединения должны быть тщательно заизолированы. а токоведущие части закрыты, см. п.6.1.

3.4 Не допускается попадания влаги на контакты клеммника и внутрь прибора.

3.5 При эксплуатации и техническом обслуживании прибора необходимо соблюдать «Правила технической эксплуатации электроустановок потребителем» и «Правила техники безопасности при эксплуатации электроустановок».

3.6 При использовании прибора совместно с нагревателем — ТЭНом, тепловентилятором, конвектором и др. обязательно заземлите последний.

3.7 Если терморегулятор с нагревателем применяются для регулирования температуры во влажном помещении – погребе, подвале, теплице…, примите дополнительные меры безопасности: используйте кабели с надежной ПВХ-изоляцией, обязательно двойной, все кабели закрепите, (используйте кабель-каналы), кабель на полу поместите в защитную трубу.

Перед тем, как войти в помещение, отключайте терморегулятор от сети!

Помните, что влажное помещение представляет собой повышенную опасность!

4 Устройство и принцип действия

4.1 Конструктивно прибор выполнен в пластмассовом щитовом корпусе. Все подключения осуществляются через клеммник, расположенный с обратной стороны.

4.2 На передней панели управления и индикации расположены:

– цифровой светодиодный индикатор;

– индикаторы «Heat» и «Cool», отображающие включенные состояния реле нагрева и охлаждения соответственно;

– кнопки для управления и программирования: «Вкл» , «S», «Вверх», «ВНИЗ»

4.3 Программируемые параметры, отображаемые меню:

F1 – установка температуры выключения реле;

F2 – задание температурного гистерезиса (от 0,3°С до 10°С).;

F3 – установка времени задержки включения реле;

F4 – задание смещения характеристики по температуре (юстировка от –10°С до +10°С).

4.4 Принцип действия. В самом общем варианте применения прибор может управлять одновременно работой нагревателя и холодильника, например, нагревателем и вентилятором в погребе зимой и осенью. Допустим, установлены след параметры: Т выкл = 5°С; гистерезис = 2°С.

Вар.1: температура датчика (в объеме) ниже 3°С Прибор нагреет датчик (объем) до 5 град, после чего реле «Heat» отключит нагреватель. Температура опустится до 3 °С – реле включится и т.д. Вар 2: температура на датчике достигла 7 град. Прибор включит холодильник (реле «Cool»), температура опустится до 5°С – холодильник выключится…

5 Подготовка к работе

5.1 Подключите к прибору сетевой кабель, кабели нагрузок (нагреватель или охладитель или то и др. вместе) согласно схеме на верхней панели прибора. В общем варианте схема может выглядеть так: контакты 1, 5 и 7 соединены вместе; контакт 6 соединен с нагревателем, 8 – с холодильником; контакт 2 соединен с нагревателем и холодильником; к контакту 1 и 2 подключен сетевой кабель.

5.2 Включите прибор в сеть, при этом на индикаторе должна отобразиться текущая температура. Если прибор не включится, нажмите и удерживайте 4 сек кнопку (в дальнейшем кн.) «Вкл».

5.3 Программирование. Режим программирования предназначен для записи в энергонезависимую память прибора требуемых параметров. Заданные значения сохраняются при выключении питания.

Нажмите и удерживайте кн. «S» до появления символа F1. Отпустите и вновь нажмите кн. «S» и, не отпуская ее, установите кнопками «Вверх» –«Вниз» температуру выключения. Отпустите все кнопки и коротко нажмите кн. « Вкл» для запоминания установленного. значения.

Перейдите к установке следующего параметра — F2: нажмите кн. «S» и удерживайте ее до появления символа F1; отпустите кн. «S» и нажмите кн. «Вверх» — появится символ F2; нажмите кн. «S» и, удерживая ее, установите значение гистерезиса. Отпустите все кнопки и коротко нажмите кн. «Вкл».

Аналогично установите параметры F3 и F4. Вначале значение F4 можно установить равным 0.

Установленные температуру и гистерезис можно проверить, нажимая поочередно кнопки «Вверх» и «Вниз».

Появление на индикаторе символа ЕЕ, сопровождающегося звуковым сигналом, сигнализирует об обрыве датчика, символа НН – о выходе за пределы диапазона измерения. Если на индикаторе появится символ Er, нажмите на кн. «S» и удерживайте ее до перезагрузки контроллера. После этого надо будет повторить настойку прибора.

Нажав и удерживая 4 сек кн. «Вкл», контроллер можно выключить и включить.

6 Юстировка

Перед эксплуатацией прибора необходимо проверить точность показания температуры в выбранном диапазоне. Для юстировки следует использовать

измеритель температуры (термометр) класса точности не хуже 0,25. Датчик температуры прибора и контрольный датчик (термометр) помещают в термостатированный объем, выдерживают по времени не менее 30 мин, и

сверяют показания. При необходимости корректируют значения параметром F4.

Периодичность проведения данной процедуры — не реже одного раза в год.

7 Гарантийные обязательства

Гарантийный срок эксплуатации – 12 месяцев со дня продажи.

В случае выхода прибора в течение этого срока при соблюдении потребителем правил эксплуатации поставщик осуществляет его бесплатный ремонт или замену. Гарантии не распространяются на изделия с внешними повреждениями корпуса прибора или датчика, с вышедшими из строя компонентами регулятора в результате неправильного соединения токоведущих проводников, превышения допустимой мощности нагрузки или короткого замыкания.

Поставщик: ООО «Лионика». г. Новосибирск, ул. Русская, 39, оф 517, тел. 383(306-58-96).

Почтовый адрес: 630060, г. Новосибирск, ая 60, тел. (383)333-69-11, 8-913-461-24-58, e-mail: lionica2000@mail.ru https://.lionica.ru

Дата продажи_______

Источник

Драйверы

5
Руководства по ремонту

1
Инструкции по эксплуатации

18

Языки:

Preview

HP LaserJet 1000 инструкция по эксплуатации
(112 страниц)

Языки:Русский
Тип:
PDF
Размер:
1.68 MB
Описание:
Лазерный принтер

Просмотр

Preview

HP LaserJet 1000 инструкция по эксплуатации
(104 страницы)

Языки:Английский
Тип:
PDF
Размер:
1.38 MB

Просмотр

Preview

HP LaserJet 1000 инструкция по эксплуатации
(104 страницы)

Языки:Турецкий
Тип:
PDF
Размер:
1.75 MB

Просмотр

Preview

HP LaserJet 1000 инструкция по эксплуатации
(108 страниц)

Языки:Греческий
Тип:
PDF
Размер:
1.68 MB

Просмотр

Preview

HP LaserJet 1000 инструкция по эксплуатации
(116 страниц)

Языки:Тайский
Тип:
PDF
Размер:
3.48 MB

Просмотр

Preview

HP LaserJet 1000 инструкция по эксплуатации
(102 страницы)

Языки:Арабский
Тип:
PDF
Размер:
2.15 MB

Просмотр

Preview

HP LaserJet 1000 инструкция по эксплуатации
(104 страницы)

Языки:Шведский
Тип:
PDF
Размер:
1.55 MB

Просмотр

Preview

HP LaserJet 1000 инструкция по эксплуатации
(108 страниц)

Языки:Французский
Тип:
PDF
Размер:
1.7 MB

Просмотр

Preview

HP LaserJet 1000 инструкция по эксплуатации
(108 страниц)

Языки:Немецкий
Тип:
PDF
Размер:
1.87 MB

Просмотр

Preview

HP LaserJet 1000 инструкция по эксплуатации
(104 страницы)

Языки:Венгерский
Тип:
PDF
Размер:
1.64 MB

Просмотр

Preview

HP LaserJet 1000 инструкция по эксплуатации
(104 страницы)

Языки:Чешский
Тип:
PDF
Размер:
2.03 MB

Просмотр

Preview

HP LaserJet 1000 инструкция по эксплуатации
(104 страницы)

Языки:Словацкий
Тип:
PDF
Размер:
2.05 MB

Просмотр

Preview

HP LaserJet 1000 инструкция по эксплуатации
(108 страниц)

Языки:Нидерландский
Тип:
PDF
Размер:
1.52 MB

Просмотр

Preview

HP LaserJet 1000 инструкция по эксплуатации
(104 страницы)

Языки:Датский
Тип:
PDF
Размер:
1.5 MB

Просмотр

Preview

HP LaserJet 1000 инструкция по эксплуатации
(103 страницы)

Языки:Иврит
Тип:
PDF
Размер:
3.01 MB

Просмотр

Preview

HP LaserJet 1000 инструкция по эксплуатации
(108 страниц)

Языки:Польский
Тип:
PDF
Размер:
1.69 MB

Просмотр

Preview

HP LaserJet 1000 инструкция по эксплуатации
(104 страницы)

Языки:Финский
Тип:
PDF
Размер:
1.71 MB

Просмотр

Preview

HP LaserJet 1000 инструкция по эксплуатации
(104 страницы)

Языки:Корейский
Тип:
PDF
Размер:
1.78 MB

Просмотр

На NoDevice можно скачать инструкцию по эксплуатации для HP LaserJet 1000. Руководство пользователя необходимо для ознакомления с правилами установки и эксплуатации HP LaserJet 1000. Инструкции по использованию помогут правильно настроить HP LaserJet 1000, исправить ошибки и выявить неполадки.

Источник

Manuals
Brands
YASKAWA Manuals
Controller
A1000 Series

Manuals and User Guides for YASKAWA A1000 Series. We have 16 YASKAWA A1000 Series manuals available for free PDF download: Technical Manual, Quick Start Manual, Installation Manual, Product Replacement Manual, Manual, Setup

YASKAWA A1000 Series Technical Manual (544 pages)

High Performance Vector Control Drive Models: 200 V Class: 0.4 to 110 kW 400 V Class: 0.4 to 355 kW

Brand: YASKAWA
|
Category: Controller
|
Size: 56.82 MB

Table of Contents

5
- Quick Reference
  
  3
  - Table of Contents
    
    5
- I.1 Preface
  
  16
  - Applicable Documentation
    
    16
  - Symbols
    
    16
  - Terms and Abbreviations
    
    16
- I.2 General Safety
  
  17
  - Supplemental Safety Information
    
    17
  - Safety Messages
    
    18
  - Application Notes
    
    19
  - Notes on Motor Operation
    
    21
  - Applications with Specialized Motors
    
    22
  - Drive Label Warnings
    
    24
  - Warranty Information
    
    24
Receiving

25
- Section Safety
  
  26
- General Description
  
  27
  - A1000 Model Selection
    
    27
  - Control Mode Selection
    
    28
- Model Number and Nameplate Check
  
  29
  - Nameplate
    
    29
- Drive Models and Enclosure Types
  
  31
- Component Names
  
  32
  - IP20/NEMA Type 1 Enclosure
    
    32
  - IP00 Enclosure
    
    32
  - Front Views
    
    35
- Mechanical Installation
  
  37
  - Section Safety
    
    38
  - Installation Environment
    
    40
- 2 Mechanical Installation
  
  40
  - Installation Orientation and Spacing
    
    40
  - Digital Operator Remote Usage
    
    42
  - Exterior and Mounting Dimensions
    
    46
Electrical Installation

51
- Section Safety
  
  52
- Standard Connection Diagram
  
  54
- Main Circuit Connection Diagram
  
  56
- Three-Phase 200 V Class (CIMR-A 2A0169 to
  
  56
- Three-Phase 400 V Class (CIMR-A 4A0088 to 0675)
  
  56
  - Terminal Block Configuration
    
    57
  - Terminal Cover
    
    59
- CIMR-A 2A0004 to 0081, 4A0002 to 0044 (IP20/NEMA Type 1 Enclosure)
  
  59
- CIMR-A 2A0110 to 0415, 4A0058 to 0675 (IP00 Enclosure)
  
  60
  - Digital Operator and
    
    61
- Removing/Reattaching the Digital Operator
  
  61
- Removing/Reattaching the Front Cover
  
  61
  - Top Protective Cover
    
    64
    
    Removing the Top Protective Cover
    
    64
    
    Reattaching the Top Protective Cover
    
    64
  - Main Circuit Wiring
    
    65
- Main Circuit Terminal Functions
  
  65
- Protecting Main Circuit Terminals
  
  65
- Wire Gauges and Tightening Torque
  
  66
- Main Circuit Terminal and Motor Wiring
  
  70
  - Control Circuit Wiring
    
    72
- Control Circuit Connection Diagram
  
  72
- Control Circuit Terminal Block Functions
  
  72
- Terminal Configuration
  
  73
- Wiring the Control Circuit Terminal
  
  74
- Switches and Jumpers on the Terminal Board
  
  76
  - Control I/O Connections
    
    77
- Sinking/Sourcing Mode Selection for Safe Disable Inputs
  
  77
- Sinking/Sourcing Mode Switch for Digital Inputs
  
  77
- Using the Pulse Train Output
  
  78
- Terminal A2 Input Signal Selection
  
  79
- Terminal A3 Analog/Ptc Input Selection
  
  79
- Terminal AM/FM Signal Selection
  
  79
- Memobus/Modbus Termination
  
  80
  - Connect to a Pc
    
    81
  - External Interlock
    
    82
- Drive Ready
  
  82
  - Wiring Checklist
    
    83
Start-Up Programming & Operation

85
- Section Safety
  
  86
- Keys and Displays
  
  87
- Using the Digital Operator
  
  87
- LCD Display
  
  88
- ALARM (ALM) LED Displays
  
  89
- LO/RE LED and RUN LED Indications
  
  89
- Menu Structure for Digital Operator
  
  90
  - The Drive and Programming Modes
    
    91
  - Navigating the Drive and Programming Modes
    
    91
  - Changing Parameter Settings or Values
    
    92
  - Verifying Parameter Changes: Verify Menu
    
    94
  - Simplified Setup Using the Setup Group
    
    95
  - Switching between LOCAL and REMOTE
    
    96
  - Start-Up Flowcharts
    
    98
  - Flowchart A: Basic Start-Up and Motor Tuning
    
    98
  - Subchart A-1: Simple Motor Setup Using V/F Control
    
    99
  - Subchart A-2: High Performance Operation Using OLV or CLV
    
    100
  - Subchart A-3: Operation with Permanent Magnet Motors
    
    101
  - Powering up the Drive
    
    102
  - Powering up the Drive and Operation Status Display
    
    102
  - Application Selection
    
    103
  - Setting 1: Water Supply Pump Application
    
    103
  - Setting 2: Conveyor Application
    
    103
  - Setting 3: Exhaust Fan Application
    
    104
  - Setting 4: HVAC Fan Application
    
    104
  - Setting 5: Compressor Application
    
    105
  - Setting 6: Hoist Application
    
    105
  - Notes on Controlling the Brake When Using the Hoist Application Preset
    
    106
  - Setting 7: Traveling Application
    
    108
  - Auto-Tuning
    
    109
  - Types of Auto-Tuning
    
    109
  - Before Auto-Tuning the Drive
    
    111
  - Auto-Tuning Interruption and Fault Codes
    
    112
  - Auto-Tuning Operation Example
    
    112
  - Parameter Settings During Induction Motor Auto-Tuning: T1
    
    114
  - Parameter Settings During PM Motor Auto-Tuning: T2
    
    116
  - Parameter Settings During Inertia and Speed Control Loop Auto-Tuning: T3
    
    119
  - No-Load Operation Test Run
    
    121
  - Test Run with Load Connected
    
    123
  - Test Run with the Load Connected
    
    123
  - Verifying Parameter Settings and Backing up Changes
    
    124
  - Backing up Parameter Values: O2-03
    
    124
  - Parameter Access Level: A1-01
    
    124
  - Password Settings: A1-04, A1-05
    
    124
  - Copy Function
    
    125
  - Test Run Checklist
    
    126
Parameter Details

129
- A1: Initialization
  
  130
- A: Initialization
  
  130
- A2: User Parameters
  
  135
- B1: Operation Mode Selection
  
  136
- B: Application
  
  136
- B2: DC Injection Braking and Short Circuit Braking
  
  144
- B3: Speed Search
  
  146
- B4: Delay Timers
  
  151
- B5: PID Control
  
  152
- B6: Dwell Function
  
  161
- B7: Droop Control (CLV, CLV/PM)
  
  162
- B8: Energy Saving
  
  163
- B9: Zero Servo
  
  164
- C1: Acceleration and Deceleration Times
  
  165
- C: Tuning
  
  165
- C2: S-Curve Characteristics
  
  167
- C3: Slip Compensation
  
  167
- C4: Torque Compensation
  
  170
- C5: Automatic Speed Regulator (ASR)
  
  171
- C6: Carrier Frequency
  
  177
  - D: Reference Settings
    
    180
- D1: Frequency Reference
  
  180
- D2: Frequency Upper/Lower Limits
  
  182
- D3: Jump Frequency
  
  182
- D4: Frequency Reference Hold and Up/Down 2 Function
  
  183
- D5: Torque Control
  
  188
- D6: Field Weakening and Field Forcing
  
  192
- D7: Offset Frequency
  
  193
  - E: Motor Parameters
    
    194
- E1: V/F Pattern for Motor 1
  
  194
- E2: Motor 1 Parameters
  
  198
- E3: V/F Pattern for Motor 2
  
  201
- E4: Motor 2 Parameters
  
  202
- E5: PM Motor Settings
  
  204
  - F: Option Settings
    
    206
- F1: PG Speed Control Card Settings
  
  206
- F2: Analog Input Card Settings
  
  209
- F3: Digital Input Card Settings
  
  209
- F4: Analog Monitor Card Settings
  
  210
- F5: Digital Output Card Settings
  
  211
- F6: Communication Option Card
  
  211
- Canopen Parameters
  
  213
- CC-Link Parameters
  
  213
- Devicenet Parameters
  
  213
  - H: Terminal Functions
    
    214
- MECHATROLINK Parameters
  
  213
- PROFIBUS-DP Parameters
  
  213
- H1: Multi-Function Digital Inputs
  
  214
- H2: Multi-Function Digital Outputs
  
  224
- H3: Multi-Function Analog Inputs
  
  234
- H4: Multi-Function Analog Outputs
  
  239
- H5: Memobus/Modbus Serial Communication
  
  241
- H6: Pulse Train Input/Output
  
  241
  - L: Protection Functions
    
    244
- L1: Motor Protection
  
  244
- L2: Momentary Power Loss Ride-Thru
  
  249
- L3: Stall Prevention
  
  255
- L4: Speed Detection
  
  262
- L5: Fault Restart
  
  263
- L6: Torque Detection
  
  264
- L7: Torque Limit
  
  267
- L8: Drive Protection
  
  269
  - N: Special Adjustments
    
    275
- N1: Hunting Prevention
  
  275
- N2: Speed Feedback Detection Control (AFR) Tuning
  
  276
- N3: High Slip Braking (HSB) and Overexcitation Braking
  
  276
- N5: Feed Forward Control
  
  279
- N6: Online Tuning
  
  280
- N8: PM Motor Control Tuning
  
  281
  - O: Operator Related Settings
    
    284
- O1: Digital Operator Display Selection
  
  284
- O2: Digital Operator Keypad Functions
  
  285
- O3: Copy Function
  
  287
- O4: Maintenance Monitor Settings
  
  288
  - Q: Driveworksez Parameters
    
    289
  - R: Driveworksez Connection Parameters
    
    289
  - T: Motor Tuning
    
    290
  - U: Monitor Parameters
    
    291
- U1: Operation Status Monitors
  
  291
- U2: Fault Trace
  
  291
- U3: Fault History
  
  291
- U4: Maintenance Monitors
  
  291
- U5: PID Monitors
  
  291
- U6: Operation Status Monitors
  
  291
- U8: Driveworksez Monitors
  
  292
Troubleshooting

293
- Section Safety
  
  294
- Fine-Tuning Open Loop Vector Control
  
  296
- Fine-Tuning V/F Control and V/F Control with PG
  
  296
- Motor Performance Fine-Tuning
  
  296
- Fine-Tuning Closed Loop Vector Control
  
  297
- Fine-Tuning Open Loop Vector Control for PM Motors
  
  297
- Fine-Tuning Advanced Open Loop Vector Control for PM Motors
  
  298
- Fine-Tuning Closed Loop Vector Control for PM Motors
  
  298
- Parameters to Minimize Motor Hunting and Oscillation
  
  299
  - Drive Alarms, Faults, and Errors
    
    300
  - Types of Alarms, Faults, and Errors
    
    300
- Alarm and Error Displays
  
  301
  - Fault Detection
    
    306
- Fault Displays, Causes, and Possible Solutions
  
  306
  - Alarm Detection
    
    319
- Alarm Codes, Causes, and Possible Solutions
  
  319
  - Operator Programming Errors
    
    325
- Ope Codes, Causes, and Possible Solutions
  
  325
  - Auto-Tuning Fault Detection
    
    328
- Auto-Tuning Codes, Causes, and Possible Solutions
  
  328
  - Copy Function Related Displays
    
    332
- Tasks, Errors, and Troubleshooting
  
  332
  - Diagnosing and Resetting Faults
    
    334
- Fault Occurs Simultaneously with Power Loss
  
  334
- If the Drive Still Has Power after a Fault Occurs
  
  334
- Viewing Fault Trace Data after Fault
  
  334
- Fault Reset Methods
  
  335
  - Troubleshooting Without Fault Display
    
    336
  - Common Problems
    
    336
  - Cannot Change Parameter Settings
    
    336
  - Motor Does Not Rotate Properly after Pressing RUN Button or after
    
    336
  - Entering External Run Command
    
    337
  - Motor Is too Hot
    
    338
  - Drive Does Not Allow Selection the Desired Auto-Tuning Mode
    
    338
  - Ope02 Error Occurs When Lowering the Motor Rated Current Setting
    
    338
  - Motor Stalls During Acceleration or Acceleration Time Is too Long
    
    338
  - Reference Command
    
    339
  - Excessive Motor Oscillation and Erratic Rotation
    
    339
  - Deceleration Takes Longer than Expected with Dynamic Braking Enabled
    
    339
  - Load Falls When Brake Is Applied (Hoist-Type Applications)
    
    339
  - Noise from Drive or Output Lines When the Drive Is Powered on
    
    340
  - Earth Leakage Circuit Breaker (ELCB) Trips During Run
    
    340
  - Connected Machinery Vibrates When Motor Rotates
    
    340
  - PID Output Fault
    
    340
  - Insufficient Starting Torque
    
    340
  - Output Frequency Is Not as High as Frequency Reference
    
    341
  - Buzzing Sound from Motor at 2 Khz
    
    341
  - Unstable Motor Speed When Using PM
    
    341
  - Motor Does Not Restart after Power Loss
    
    341

YASKAWA A1000 Series Technical Manual (628 pages)

High Performance Vector Control Drive
Type: CIMR-A series
Models: 200 V Class: 0.55 to 110 kW,
400 V Class: 0.55 to 630 kW

Brand: YASKAWA
|
Category: Controller
|
Size: 55.44 MB

Table of Contents

5
- YASKAWA ELECTRIC SIEP C710616 27G YASKAWA AC Drive A1000 Technical Manual
  
  13
  - I.1 Preface
    
    15
  - Applicable Documentation
    
    16
  - I.2 General Safety
    
    19
  - Application Notes
    
    21
  - Notes on Motor Operation
    
    23
  - Applications with Specialized Motors
    
    24
  - Drive Label Warnings
    
    25
  - Warranty Information
    
    26
Receiving

27
- Section Safety
  
  28
- General Description
  
  29
- General Description
  
  31
- Model Number and Nameplate Check
  
  32
- Drive Models and Enclosure Types
  
  33
- Drive Models and Enclosure Types
  
  34
- Component Names
  
  35
- Component Names
  
  37
- IP00 Enclosure
  
  38
- Front Views
  
  42
- 2 Mechanical Installation
  
  43
  - Section Safety
    
    44
  - Mechanical Installation
    
    48
    
    Digital Operator Remote Usage
    
    50
    
    Exterior and Mounting Dimensions
    
    52
Electrical Installation

57
- Section Safety
  
  58
- Standard Connection Diagram
  
  60
- Standard Connection Diagram
  
  62
- Main Circuit Configurations
  
  63
- Main Circuit Configurations
  
  65
- Terminal Block Configuration
  
  66
- Terminal Block Configuration
  
  67
- Terminal Cover
  
  68
- Terminal Cover
  
  69
- Digital Operator and
  
  70
- Digital Operator and Front Cover
  
  71
- Top Protective Cover
  
  74
- Main Circuit Wiring
  
  75
- Protecting Main Circuit Terminals
  
  76
- Main Circuit Terminal and Motor Wiring
  
  81
  - Control Circuit Wiring
    
    83
- Terminal Configuration
  
  84
- Wiring the Control Circuit Terminal
  
  85
- Switches and Jumpers on the Terminal Board
  
  87
  - Control I/O Connections
    
    88
- Using the Pulse Train Output
  
  89
- Terminal A2 Input Signal Selection
  
  90
- Memobus/Modbus Termination
  
  91
  - Connect to a Pc
    
    92
  - External Interlock
    
    93
  - Wiring Checklist
    
    94
Start-Up Programming & Operation

97
- Section Safety
  
  98
- Using the Digital Operator
  
  99
- LCD Display
  
  100
- ALARM (ALM) LED Displays
  
  101
- Menu Structure for Digital Operator
  
  102
  - The Drive and Programming Modes
    
    103
- Changing Parameter Settings or Values
  
  105
- Verifying Parameter Changes: Verify Menu
  
  106
- Simplified Setup Using the Setup Group
  
  107
- Switching between LOCAL and REMOTE
  
  108
  - Start-Up Flowcharts
    
    109
  - Subchart A-1: Simple Motor Setup Using V/F Control
    
    110
  - Subchart A-2: High Performance Operation Using OLV or CLV
    
    111
  - Subchart A-3: Operation with Permanent Magnet Motors
    
    112
  - Powering up the Drive
    
    113
  - Application Selection
    
    114
  - Setting 2: Conveyor Application
    
    115
  - Setting 5: Compressor Application
    
    116
  - Notes on Controlling the Brake When Using the Hoist Application Preset
    
    117
  - Setting 7: Traveling Application
    
    119
  - Auto-Tuning
    
    120
  - Before Auto-Tuning the Drive
    
    123
  - Auto-Tuning Interruption and Fault Codes
    
    125
  - Parameter Settings During Induction Motor Auto-Tuning: T1
    
    127
  - Parameter Settings During PM Motor Auto-Tuning: T2
    
    130
  - Parameter Settings During Inertia and Speed Control Loop Auto-Tuning: T3
    
    132
  - No-Load Operation Test Run
    
    134
  - Test Run with Load Connected
    
    136
  - Verifying Parameter Settings and Backing up Changes
    
    137
  - Copy Function
    
    138
  - Test Run Checklist
    
    139
Parameter Details

141
- A: Initialization
  
  142
- A2: User Parameters
  
  147
- B: Application
  
  148
- B2: DC Injection Braking and Short Circuit Braking
  
  158
- B3: Speed Search
  
  160
- B4: Delay Timers
  
  166
- B5: PID Control
  
  167
- B6: Dwell Function
  
  178
- B8: Energy Saving
  
  179
- B9: Zero Servo
  
  181
- C: Tuning
  
  183
- C2: S-Curve Characteristics
  
  185
- C4: Torque Compensation
  
  188
- C5: Automatic Speed Regulator (ASR)
  
  190
- C6: Carrier Frequency
  
  195
  - D: Reference Settings
    
    198
- D2: Frequency Upper/Lower Limits
  
  200
- D4: Frequency Reference Hold and Up/Down 2 Function
  
  201
- D5: Torque Control
  
  206
- D6: Field Weakening and Field Forcing
  
  210
- D7: Offset Frequency
  
  211
  - E: Motor Parameters
    
    212
- E2: Motor 1 Parameters
  
  216
- E3: V/F Pattern for Motor 2
  
  219
- E4: Motor 2 Parameters
  
  220
- E5: PM Motor Settings
  
  222
  - F: Option Settings
    
    225
- F2: Analog Input Card Settings
  
  228
- F3: Digital Input Card Settings
  
  229
- F4: Analog Monitor Card Settings
  
  230
- F5: Digital Output Card Settings
  
  231
  - H: Terminal Functions
    
    235
- H2: Multi-Function Digital Outputs
  
  246
- H3: Multi-Function Analog Inputs
  
  257
- H4: Multi-Function Analog Outputs
  
  262
- H5: Memobus/Modbus Serial Communication
  
  264
  - L: Protection Functions
    
    267
- L2: Momentary Power Loss Ride-Thru
  
  274
- L3: Stall Prevention
  
  281
- L4: Speed Detection
  
  288
- L5: Fault Restart
  
  290
- L6: Torque Detection
  
  291
- L7: Torque Limit
  
  294
- L8: Drive Protection
  
  295
- L9: Drive Protection 2
  
  301
  - N: Special Adjustments
    
    302
- N2: Speed Feedback Detection Control (AFR) Tuning
  
  303
- N5: Feed Forward Control
  
  306
- N6: Online Tuning
  
  307
- N8: PM Motor Control Tuning
  
  308
  - O: Operator Related Settings
    
    314
- O2: Digital Operator Keypad Functions
  
  315
- O3: Copy Function
  
  318
  - Q: Driveworksez Parameters
    
    320
  - U: Monitor Parameters
    
    321
  - U6: Control Monitors
    
    322
Troubleshooting

323
- Section Safety
  
  324
- Motor Performance Fine-Tuning
  
  326
- Fine-Tuning Closed Loop Vector Control
  
  327
- Fine-Tuning Advanced Open Loop Vector Control for PM Motors
  
  328
- Parameters to Minimize Motor Hunting and Oscillation
  
  329
- Drive Alarms, Faults, and Errors
  
  330
- Alarm and Error Displays
  
  331
- Fault Detection
  
  336
- Alarm Detection
  
  350
- Operator Programming Errors
  
  357
- Causes and Possible Solutions for a Blank and Unresponsive Digital Operator
  
  359
- Auto-Tuning Fault Detection
  
  360
- Copy Function Related Displays
  
  364
- Diagnosing and Resetting Faults
  
  366
- Fault Reset Methods
  
  367
- Troubleshooting Without Fault Display
  
  368
- External Run Command
  
  369
- Motor Is too Hot
  
  370
- Motor Stalls During Acceleration or Acceleration Time Is too Long
  
  371
- Deceleration Takes Longer than Expected with Dynamic Braking Enabled
  
  372
- PID Output Fault
  
  373
- Unstable Motor Speed When Using PM
  
  374

YASKAWA A1000 Series Quick Start Manual (358 pages)

High Performance Vector Control Drive

Brand: YASKAWA
|
Category: Controller
|
Size: 14.79 MB

Quick Reference

3
Table of Contents

5
Preface & General Safety

11
- Preface
  
  12
  - Applicable Documentation
    
    12
  - I.1 Preface
    
    12
- General Safety
  
  13
  - Supplemental Safety Information
    
    13
  - I.2 General Safety
    
    13
  - Safety Messages
    
    14
  - General Application Precautions
    
    15
  - Motor Application Precautions
    
    18
  - Drive Label Warning Example
    
    20
  - Warranty Information
    
    20
1 Receiving

21
- Model Number and Nameplate Check
  
  22
  - Nameplate
    
    22
2 Mechanical Installation

27
- Mechanical Installation
  
  28
  - Installation Environment
    
    28
  - Installation Orientation and Spacing
    
    28
  - Instructions on Installation Using the Eye Bolts
    
    30
- Flange Type Enclosure (NEMA 12 Backside) Dimensions & Heat Loss
  
  41
  - Flange Type Models 2A0004 to 2A0012, 4A0002 to 4A0005, and 5A0003 and 5A0004
    
    41
  - Flange Type Models 2A0018 and 2A0021, 4A0007 to 4A0011, and 5A0006 and 5A0009
    
    44
  - Flange Type Models 2A0030 and 2A0040, 4A0018 and 4A0023, and 5A0011
    
    47
  - Flange Type Model 4A0031
    
    50
  - Flange Type Models 2A0056, 4A0038, and 5A0017 and 5A0022
    
    52
  - Flange Type Models 2A0069 and 2A0081, 4A0044, and 5A0027 and 5A0032
    
    55
  - Flange Type Models 2A0110 and 4A0058
    
    58
  - Flange Type Models 2A0138, 4A0072, and 5A0041 and 5A0052
    
    60
  - Flange Type Models 4A0088 and 4A0103
    
    62
  - Flange Type Models 2A0169 and 2A0211, 4A0139 and 4A0165, and 5A0062 to 5A0099
    
    64
  - Flange Type Models 2A0250 and 2A0312, 4A0208, and 5A0125 and 5A0145
    
    67
  - Flange Type Models 2A0360 and 2A0415, 4A0250 to 4A0362, and 5A0192 and 5A0242
    
    69
  - Flange Type Model 4A0414
    
    72
  - Flange Type Models 4A0515 and 4A0675
    
    74
  - Flange Type Models 4A0930 and 4A1200
    
    76
3 Electrical Installation

79
- Standard Connection Diagram
  
  80
- Main Circuit Connection Diagram
  
  83
  - Three-Phase 200 V Class Models 2A0004 to 2A0081 Three-Phase 400 V Class Models 4A0002 to 4A0044 Three-Phase 600 V Class Models 5A0003 to 5A0032
    
    83
  - Three-Phase 200 V Class Models 2A0110, 2A0138 Three-Phase 400 V Class Models 4A0058, 4A0072 Three-Phase 600 V Class Models 5A0041, 5A0052
    
    83
  - Three-Phase 200 V Class Models 2A0169 to 2A0211 Three-Phase 400 V Class Models 4A0088 to 4A0139 Three-Phase 600 V Class Models 5A0062 to 5A0099
    
    84
  - Three-Phase 200 V Class Models 2A0250 to 2A0415 Three-Phase 400 V Class Models 4A0165 to 4A0675 Three-Phase 600 V Class Models 5A0125 to 5A0242
    
    84
  - Three-Phase 400 V Class Models 4A0930, 4A1200
    
    85
  - 12-Pulse Rectification
    
    85
- Terminal Cover
  
  87
  - Models 2A0004 to 2A0081, 4A0002 to 4A0044, 5A0003 to 5A0032 (IP20/NEMA 1, UL Type 1 Enclosure)
    
    87
  - Models 2A0110 to 2A0250, 4A0208 to 4A1200, and 5A0125 to 5A0242 (Ip00/Open Type Enclosure)
    
    88
- Digital Operator and
  
  89
  - Removing/Reattaching the Digital Operator
    
    89
  - Removing/Reattaching the
    
    89
- Top Protective Cover
  
  92
  - Removing the Top Protective Cover
    
    92
  - Reattaching the Top Protective Cover
    
    92
- Main Circuit Wiring
  
  93
  - Main Circuit Terminal Functions
    
    93
  - Protecting Main Circuit Terminals
    
    94
  - Main Circuit Wire Gauges and Tightening Torques
    
    94
  - Main Circuit Terminal and Motor Wiring
    
    103
- Control Circuit Wiring
  
  105
  - Control Circuit Terminal Block Functions
    
    105
  - Terminal Configuration
    
    107
  - Wiring the Control Circuit Terminal
    
    108
- Control I/O Connections
  
  110
  - Sinking/Sourcing Mode for Digital Inputs
    
    110
  - Sinking/Sourcing Mode Selection for Safe Disable Inputs
    
    111
  - Using the Pulse Train Output
    
    112
  - Terminal A2 Input Signal Selection
    
    113
  - Terminal A3 Analog/Ptc Input Selection
    
    113
  - Terminal AM/FM Signal Selection
    
    113
  - Terminal DM+ and DM- Output Signal Selection
    
    114
- Connect to a PC
  
  115
- Wiring Checklist
  
  116
4 Start-Up Programming & Operation

119
- Using the Digital Operator
  
  120
  - Digital Operator Keys and Displays
    
    120
  - LCD Display
    
    121
  - ALARM (ALM) LED Displays
    
    122
  - LO/RE LED and RUN LED Indications
    
    122
  - Menu Structure for Digital Operator
    
    123
- The Drive and Programming Modes
  
  124
  - Changing Parameter Settings or Values
    
    124
  - Switching between LOCAL and REMOTE
    
    126
- Start-Up Flowcharts
  
  127
  - Flowchart A: Basic Start-Up and Motor Tuning
    
    128
  - Subchart A-1: Simple Motor Setup Using V/F Control
    
    129
  - Subchart A-2: High Performance Operation Using OLV or CLV
    
    130
  - Subchart A-3: Operation with Permanent Magnet Motors
    
    131
- Powering up the Drive
  
  133
  - Powering up the Drive and Operation Status Display
    
    133
- Application Selection
  
  134
- Basic Drive Setup Adjustments
  
  135
- Auto-Tuning
  
  164
  - Types of Auto-Tuning
    
    164
  - Auto-Tuning Interruption and Fault Codes
    
    167
  - Auto-Tuning Operation Example
    
    169
- No-Load Operation Test Run
  
  171
- Test Run with Load Connected
  
  173
  - Test Run with the Load Connected
    
    173
- Test Run Checklist
  
  174
5 Troubleshooting

177
- Drive Alarms, Faults, and Errors
  
  178
  - Types of Alarms, Faults, and Errors
    
    178
- Fault Detection
  
  179
  - Fault Displays, Causes, and Possible Solutions
    
    179
- Alarm Detection
  
  196
  - Alarm Codes, Causes, and Possible Solutions
    
    196
- Operator Programming Errors
  
  203
  - Operator Programming Error Codes, Causes, and Possible Solutions
    
    203
  - Causes and Possible Solutions for a Blank and Unresponsive Digital Operator
    
    204
- Auto-Tuning Fault Detection
  
  205
  - Auto-Tuning Codes, Causes, and Possible Solutions
    
    205
- Copy Function Related Displays
  
  211
  - Tasks, Errors, and Troubleshooting
    
    211
  - Fault Reset Methods
    
    211
6 Periodic Inspection & Maintenance

213
- Inspection
  
  214
  - Recommended Daily Inspection
    
    214
  - Recommended Periodic Inspection
    
    215
  - Storage Guidelines
    
    216
- Periodic Maintenance
  
  217
  - Replacement Parts
    
    217
- Drive Replacement
  
  219
  - Replacing the Drive
    
    219
7 Peripheral Devices & Options

221
- Option Card Installation
  
  222
  - Prior to Installing the Option
    
    222
  - PG Option Installation Example
    
    223
Specifications

233
- Heavy Duty and Normal Duty Ratings
  
  234
- Power Ratings
  
  235
  - Three-Phase 200 V Class Drive Models 2A0004 to 2A0030
    
    235
  - Three-Phase 200 V Class Drive Models 2A0040 to 2A0211
    
    236
  - Three-Phase 200 V Class Drive Models 2A0250 to 2A0415
    
    237
  - Three-Phase 400 V Class Drive Models 4A0002 to 4A0031
    
    238
  - Three-Phase 400 V Class Drive Models 4A0038 to 4A0165
    
    239
  - Three-Phase 400 V Class Drive Models 4A0208 to 4A1200
    
    240
  - Three-Phase 600 V Class Drive Models 5A0003 to 5A0032
    
    241
  - Three-Phase 600 V Class Drive Models 5A0041 to 5A0099
    
    242
  - Three-Phase 600 V Class Drive Models 5A0125 to 5A0242
    
    243
- Drive Specifications
  
  244
- Drive Watt Loss Data
  
  246

YASKAWA A1000 Series Technical Manual (257 pages)

Brand: YASKAWA
|
Category: Controller
|
Size: 14.89 MB

Quick Reference

3
Table of Contents

5
Preface & General Safety

11
- Preface
  
  12
  - Applicable Documentation
    
    12
  - I.1 Preface
    
    12
- General Safety
  
  13
  - Supplemental Safety Information
    
    13
  - I.2 General Safety
    
    13
  - Safety Messages
    
    14
  - General Application Precautions
    
    15
  - Motor Application Precautions
    
    18
  - Drive Label Warning Example
    
    20
  - Warranty Information
    
    20
1 Receiving

21
- Model Number and Nameplate Check
  
  22
  - Nameplate
    
    22
2 Mechanical Installation

27
- Mechanical Installation
  
  28
  - Installation Environment
    
    28
  - Installation Orientation and Spacing
    
    28
3 Electrical Installation

37
- Standard Connection Diagram
  
  38
- Main Circuit Connection Diagram
  
  41
  - Three-Phase 200 V Class (CIMR-Ao2A0004 to 2A0081) Three-Phase 400 V Class (CIMR-Ao4A0002 to 4A0044) Three-Phase 600 V Class (CIMR-Ao5A0003 to 5A0032)
    
    41
  - Three-Phase 200 V Class (CIMR-Ao2A0110, 2A0138) Three-Phase 400 V Class (CIMR-Ao4A0058, 4A0072) Three-Phase 600 V Class (CIMR-Ao5A0041, 5A0052)
    
    41
  - Three-Phase 200 V Class (CIMR-Ao2A0169 to 2A0415) Three-Phase 400 V Class (CIMR-Ao4A0088 to 4A0675) Three-Phase 600 V Class (CIMR-Ao5A0062 to 5A0099)
    
    41
  - Three-Phase 400 V Class (CIMR-Ao4A0930, 4A1200)
    
    42
  - 12-Phase Rectification
    
    42
- Terminal Cover
  
  44
  - CIMR-Ao2A0004 to 2A0081, 4A0002 to 4A0044, 5A0003 to 5A0032
    
    44
  - (IP20/NEMA Type 1 Enclosure)
    
    44
  - CIMR-Ao2A0110 to 2A0415, 4A0058 to 4A1200 (IP00 Enclosure)
    
    45
- Digital Operator and
  
  46
  - Removing/Reattaching the Digital Operator
    
    46
  - Removing/Reattaching the
    
    46
- Top Protective Cover
  
  49
  - Removing the Top Protective Cover
    
    49
  - Reattaching the Top Protective Cover
    
    49
- Main Circuit Wiring
  
  50
  - Main Circuit Terminal Functions
    
    50
  - Protecting Main Circuit Terminals
    
    51
  - Wire Gauges and Tightening Torque
    
    52
  - Main Circuit Terminal and Motor Wiring
    
    59
- Control Circuit Wiring
  
  61
  - Control Circuit Terminal Block Functions
    
    61
  - Terminal Configuration
    
    63
  - Wiring the Control Circuit Terminal
    
    64
- Control I/O Connections
  
  66
  - Sinking/Sourcing Mode Switch for Digital Inputs
    
    66
  - Sinking/Sourcing Mode Selection for Safe Disable Inputs
    
    67
  - Using the Pulse Train Output
    
    67
  - Terminal A2 Input Signal Selection
    
    68
  - Terminal A3 Analog/Ptc Input Selection
    
    68
  - Terminal AM/FM Signal Selection
    
    69
- Connect to a PC
  
  70
- Wiring Checklist
  
  71
4 Start-Up Programming & Operation

73
- Using the Digital Operator
  
  74
  - Keys and Displays
    
    74
  - LCD Display
    
    75
  - ALARM (ALM) LED Displays
    
    76
  - LO/RE LED and RUN LED Indications
    
    76
  - Menu Structure for Digital Operator
    
    77
- The Drive and Programming Modes
  
  78
  - Changing Parameter Settings or Values
    
    78
  - Switching between LOCAL and REMOTE
    
    79
- Start-Up Flowcharts
  
  81
  - Flowchart A: Basic Start-Up and Motor Tuning
    
    82
  - Subchart A-1: Simple Motor Setup Using V/F Control
    
    83
  - Subchart A-2: High Performance Operation Using OLV or CLV
    
    84
  - Subchart A-3: Operation with Permanent Magnet Motors
    
    85
- Powering up the Drive
  
  86
  - Powering up the Drive and Operation Status Display
    
    86
- Application Selection
  
  87
- Basic Drive Setup Adjustments
  
  88
- Auto-Tuning
  
  116
  - Types of Auto-Tuning
    
    116
  - Auto-Tuning Interruption and Fault Codes
    
    119
  - Auto-Tuning Operation Example
    
    119
- No-Load Operation Test Run
  
  122
- Test Run with Load Connected
  
  124
  - Test Run with the Load Connected
    
    124
- Test Run Checklist
  
  125
5 Troubleshooting

127
- Drive Alarms, Faults, and Errors
  
  128
  - Types of Alarms, Faults, and Errors
    
    128
- Fault Detection
  
  129
  - Fault Displays, Causes, and Possible Solutions
    
    129
- Alarm Detection
  
  140
  - Alarm Codes, Causes, and Possible Solutions
    
    140
- Operator Programming Errors
  
  143
  - Operator Programming Error Codes, Causes, and Possible Solutions
    
    143
- Auto-Tuning Fault Detection
  
  144
  - Auto-Tuning Codes, Causes, and Possible Solutions
    
    144
- Copy Function Related Displays
  
  148
  - Tasks, Errors, and Troubleshooting
    
    148
  - Fault Reset Methods
    
    148
6 Periodic Inspection & Maintenance

149
- Inspection
  
  150
  - Recommended Daily Inspection
    
    150
  - Recommended Periodic Inspection
    
    151
- Periodic Maintenance
  
  153
  - Replacement Parts
    
    153
- Drive Replacement
  
  155
  - Replacing the Drive
    
    155
7 Peripheral Devices & Options

157
- Option Card Installation
  
  158
  - Installing Option Cards
    
    158
  - Installation Procedure
    
    158
Specifications

161
- Heavy Duty and Normal Duty Ratings
  
  162
- Power Ratings
  
  163
  - Three-Phase 200 V Class Drive Models CIMR-Ao2A0004 to 2A0030
    
    163
  - Three-Phase 200 V Class Drive Models CIMR-Ao2A0040 to 2A0211
    
    164
  - Three-Phase 200 V Class Drive Models CIMR-Ao2A0250 to 2A0415
    
    165
  - Three-Phase 400 V Class Drive Models CIMR-Ao4A0002 to 4A0031
    
    166
  - Three-Phase 400 V Class Drive Models CIMR-Ao4A0038 to 4A0165
    
    167
  - Three-Phase 400 V Class Drive Models CIMR-Ao4A0208 to 4A1200
    
    168
  - Three-Phase 600 V Class Drive Models CIMR-Ao5A0003 to 5A0032
    
    169
  - Three-Phase 600 V Class Drive Models CIMR-Ao5A0041 to 5A0099
    
    170
- Drive Specifications
  
  171
- Drive Watt Loss Data
  
  173

YASKAWA A1000 Series Quick Start Manual (195 pages)

High Performance Vector Control Drive

Brand: YASKAWA
|
Category: Controller
|
Size: 20.58 MB

Quick Reference

3
Table of Contents

5
Preface & General Safety

7
- Preface
  
  7
- General Safety
  
  7
1 Receiving

17
- Model Number and Nameplate Check
  
  17
2 Mechanical Installation

19
3 Electrical Installation

26
- Standard Connection Diagram
  
  26
- Main Circuit Connection Diagram
  
  28
- Terminal Cover
  
  29
- Digital Operator and
  
  31
- Top Protective Cover
  
  33
- Main Circuit Wiring
  
  34
- Control I/O Connections
  
  48
- Terminal A2 Analog Input Signal Selection
  
  50
- Connect to a PC
  
  51
- Wiring Checklist
  
  51
4 Start-Up Programming & Operation

53
- Using the Digital Operator
  
  53
- The Drive and Programming Modes
  
  56
- Start-Up Flowcharts
  
  58
- Powering up the Drive
  
  63
- Application Selection
  
  63
- Basic Drive Setup Adjustments
  
  64
- Auto-Tuning
  
  91
- No-Load Operation Test Run
  
  95
- Test Run with Load Connected
  
  96
- Test Run Checklist
  
  97
5 Troubleshooting

99
- Drive Alarms, Faults, and Errors
  
  99
- Fault Detection
  
  100
- Alarm Detection
  
  110
- Operator Programming Errors
  
  112
- Auto-Tuning Fault Detection
  
  113
- Copy Function Related Displays
  
  117
6 Periodic Inspection & Maintenance

118
- Inspection
  
  118
- Periodic Maintenance
  
  120
Specifications

124
- Heavy Duty and Normal Duty Ratings
  
  124
- Three-Phase 200 V Class Drives
  
  125
- Three-Phase 400 V Class Drives
  
  126
- Drive Specifications
  
  128
- Drive Watt Loss Data
  
  129
Parameter List

131
- A: Initialization Parameters
  
  131
- B: Application
  
  132
- C: Tuning
  
  137
- D: References
  
  141
- E: Motor Parameters
  
  144
- F: Options
  
  148
- H: Multi-Function Terminals
  
  154
- L: Protection Function
  
  162
- N: Special Adjustment
  
  168
- O: Operator Related Settings
  
  170
- Q: Driveworksez Parameters
  
  172
- R: Driveworksez Connection Parameters
  
  172
- T: Motor Tuning
  
  172
- U: Monitors
  
  175

YASKAWA A1000 Series Installation Manual (70 pages)

Brand: YASKAWA
|
Category: DC Drives
|
Size: 5.37 MB

Table of Contents

3
Preface & General Safety

5
Preface

6
Applicable Documentation

6
General Safety

7
General Application Precautions

7
Receiving

9
Model Number and Nameplate Check

10
Nameplate

10
Component Names

12
Flange Type Enclosure (NEMA Type 12 Backside)

12
Mechanical Installation

13
Mechanical Installation

14
Installation Environment

14
Removing the Shipping Package Attachments

15
Dimensions

15
Panel Cut-Out Dimensions

21
Weight

25
Electrical Installation

27
Standard Connection Diagram

28
Main Circuit Connection Diagram

31
6-Phase/12-Pulse Input 400 V Class (CIMR-A 4T0058, 0072)

31
6-Phase/12-Pulse Input 400 V Class (CIMR-A 4T0088 to 0139)

31
6-Phase/12-Pulse Input 400 V Class (CIMR-A 4T0165 to 0675)

32
6-Phase/12-Pulse Rectification

33
Main Circuit Terminal Configuration

34
Main Circuit Wiring

37
Main Circuit Terminal Functions

37
Main Circuit Fuses

37
Wire Gauges and Tightening Torque

38
Wiring Checklist

41
Start-Up Programming & Operation

43
Powering up the Drive

44
Peripheral Devices & Options

45
Drive Options and Peripheral Devices

46
Connecting Peripheral Devices

48
Installing Peripheral Devices

49
Dynamic Braking Options

49
Specifications

51
Power Ratings

52
6-Phase/12 Pulse Input 400 V Class Drive Models CIMR-A 4T0058 to 0208

52
6-Phase/12 Pulse Input 400 V Class Drive Models CIMR-A 4T0208 to 0675

53
Drive Specifications

54
Drive Watt Loss Data

56
Drive Derating Data

57
Temperature Derating

57
Altitude Derating

57
Parameter List

59
L: Protection Function

60
L8: Drive Protection

60

YASKAWA A1000 Series Product Replacement Manual (44 pages)

Brand: YASKAWA
|
Category: Inverter
|
Size: 1.77 MB

Table of Contents

1
Applicable Models

2
Replacement Checklist

4
Terminal Compatibility Chart

6
Main Circuit Terminals

6
Control Circuit Terminals, Signal Levels

12
Communication Circuit Terminals

15
Terminal Sizes and Wire Gauge

16
Dimensions and Installation Adapters

29
Exterior and Mounting Dimensions

29
UL Type 1 Kit

32
Adapters and Attachments to Match Mounting Dimensions

34
Braking Resistor Installation Attachment

36
Parameter Transition Guide

37
Parameter Setting Transition Instructions

37
Checking Modified Parameters with A1000 Verify Menu

37
Parameter Compatibility Table

38
Carrier Frequency and Rated Current Derating

40
Matching Keypad and Operator

42
Revision History

44

YASKAWA A1000 Series Quick Start Manual (52 pages)

Frequency High Performance Vector Control AC Drive

Brand: YASKAWA
|
Category: Controller
|
Size: 5.92 MB

Table of Contents

3
Safety Instructions and General Warnings

4
Mechanical Installation

8
Figure

9
Electrical Installation

12
Keypad Operation

19
Start up

21
Parameter Table

26
Troubleshooting

31
Safe Disable Input Function

35
Ul Standards

38

YASKAWA A1000 Series Technical Manual (44 pages)

Brand: YASKAWA
|
Category: Controller
|
Size: 3.96 MB

Table of Contents

3
Preface and Safety

4
Product Overview

6
Receiving

7
Option Components

8
Installation Procedure

10
Related Parameters

18
Option Data and I/O Maps

20
Parameter Process Data Object Formats

28
Troubleshooting

40
Specifications

42

YASKAWA A1000 Series Quick Start Manual (44 pages)

IP23/54 Floor Standing Panel, 400 V Class: 90 to 315 kW

Brand: YASKAWA
|
Category: Controller
|
Size: 4 MB

Table of Contents

3
Safety Instructions and General Warnings

4
Mechanical Installation

9
Electrical Installation

13
Keypad Operation

22
Start up

24
Parameter Table

29
Troubleshooting

34
Maintenance

38
Safe Disable Input Function

40

YASKAWA A1000 Series Manual (19 pages)

Brand: YASKAWA
|
Category: Controller
|
Size: 3 MB

Table of Contents

3
Preface and Safety

5
Applicable Documentation

5
Supplemental Safety Information

5
Obtaining Support

5
Product Overview

6
Applicable Models

6
Application Selection

7
Traverse Anti-Phase

7
Basic Concept

7
Limitations

7
Control Modes, Symbols, and Terms

8
Related Parameters and Functions

9
Modified Parameters

9
Additional Parameters

9
Function Text

10
Monitor Function Text

10
Multi-Function Input Settings

10
Multi-Function Output Settings

10
Function Description

11
Machine Parameter Selection

11
Application Example

12
Software and Hardware Configuration for A1000 Traverse

12
Implementation

12
Sample Operating Parameters

12
Master and Slave Output Diagram: Standard Operation

13
Traverse Operation Exceeds Maximum Output Frequency

14
Changing Reference Frequency

14
Traverse Mode Operation with Changing Frequency Reference

15
Revision History

16

YASKAWA A1000 Series Installation Manual (31 pages)

Motor PG Feedback Line Driver Interface

Brand: YASKAWA
|
Category: Recording Equipment
|
Size: 3.18 MB

Table of Contents

2
Preface and Safety

3
Product Overview

6
Receiving

7
Option Components

8
Installation Procedure

9
Related Parameters

21
Troubleshooting

24
Specifications

29

YASKAWA A1000 Series Installation Manual (30 pages)

AC Drive, Option, Analog Input

Brand: YASKAWA
|
Category: DC Drives
|
Size: 3.36 MB

Table of Contents

3
Preface and Safety

4
Product Overview

7
Receiving

8
Option Components

9
Installation Procedure

10
Related Parameters

22
Troubleshooting

26
Specifications

28

YASKAWA A1000 Series Manual (36 pages)

AC Drive

Brand: YASKAWA
|
Category: DC Drives
|
Size: 1.71 MB

YASKAWA A1000 Series Installation Manual (24 pages)

AC Drive Option, 120 Vac Digital input

Brand: YASKAWA
|
Category: Controller
|
Size: 1.98 MB

Table of Contents

3
Preface and Safety

4
Product Overview

7
Receiving

8
Option Components

9
Installation Procedure

10
Troubleshooting

21
Specifications

22

YASKAWA A1000 Series Setup (4 pages)

TCP Modbus Communication

Brand: YASKAWA
|
Category: Media Converter
|
Size: 0.89 MB

YASKAWA Categories

Controller

DC Drives

Servo Drives

Robotics

Control Unit

More YASKAWA Manuals

Источник

Manuals and User Guides for YASKAWA A1000 Series. We have 16 YASKAWA A1000 Series manuals available for free PDF download: Technical Manual, Quick Start Manual, Installation Manual, Product Replacement Manual, Manual, Setup

YASKAWA A1000 Series Technical Manual (544 pages)

Table of Contents

Table of Contents

Quick Reference

I.1 Preface

I.2 General Safety

Receiving

Electrical Installation

Start-Up Programming & Operation

Parameter Details

Troubleshooting

YASKAWA A1000 Series Technical Manual (628 pages)

Table of Contents

Table of Contents

Receiving

Electrical Installation

Start-Up Programming & Operation

Parameter Details

Troubleshooting

YASKAWA A1000 Series Quick Start Manual (358 pages)

Table of Contents

Quick Reference

Preface & General Safety

Preface

General Safety

1 Receiving

2 Mechanical Installation

3 Electrical Installation

4 Start-Up Programming & Operation

5 Troubleshooting

6 Periodic Inspection & Maintenance

7 Peripheral Devices & Options

Specifications

Heavy Duty and Normal Duty Ratings

Power Ratings

Drive Specifications

Drive Watt Loss Data

YASKAWA A1000 Series Technical Manual (257 pages)

Table of Contents

Quick Reference

Preface & General Safety

Preface

General Safety

1 Receiving

2 Mechanical Installation

3 Electrical Installation

4 Start-Up Programming & Operation

5 Troubleshooting

6 Periodic Inspection & Maintenance

7 Peripheral Devices & Options

Specifications

Heavy Duty and Normal Duty Ratings

Power Ratings

Drive Specifications

Drive Watt Loss Data

YASKAWA A1000 Series Quick Start Manual (195 pages)

Table of Contents

Preface & General Safety

1 Receiving

2 Mechanical Installation

3 Electrical Installation

4 Start-Up Programming & Operation

5 Troubleshooting

6 Periodic Inspection & Maintenance

Specifications

Parameter List

YASKAWA A1000 Series Installation Manual (70 pages)

Table of Contents

YASKAWA A1000 Series Product Replacement Manual (44 pages)

Table of Contents

YASKAWA A1000 Series Quick Start Manual (52 pages)

Table of Contents

YASKAWA A1000 Series Technical Manual (44 pages)

Table of Contents

YASKAWA A1000 Series Quick Start Manual (44 pages)

Table of Contents

YASKAWA A1000 Series Manual (19 pages)

Table of Contents

YASKAWA A1000 Series Installation Manual (31 pages)