Covidien puritan bennett 560 ventilator инструкция

• Page 1
  User Manual Puritan Bennett 560 Ventilator…
• Page 2
  Nothing in this manual shall limit or restrict in any way Covidien’s right to revise or otherwise change or modify the equipment (including its software) described herein, without notice. In the absence of…

• Page 3: Table Of Contents

  Table of Contents Preface Purpose of This Manual …………xi Qualification of Personnel .

• Page 4
  Table of Contents 2.11 USB Memory Device Menu ……….2-11 2.12 If Ventilator Failure Occurs .
• Page 5
  Table of Contents Operating Procedures Turning on the Ventilator ……….. 5-1 USB Menu Parameters .
• Page 6
  Table of Contents Indicators and Alarms …………A-2 Performance .
• Page 7
  List of Figures Figure 1-1.   Locations of Labels—Top-Front View ……….. . 1-25 Figure 1-2.  …
• Page 8
  List of Figures Figure 4-24.   Mounting the Ventilator on the Utility Cart……….4-29 Figure 4-25.  …
• Page 9
  List of Tables Table 1-1.   Ventilator Symbols …………..1-19 Table 1-2.  …
• Page 10
  Page Left Intentionally Blank…

• Page 11: Purpose Of This Manual

  Information regarding your product warranty is available from your sales representative or Covidien. Extended Service The Puritan Bennett™ 560 ventilator offers extended service contracts/warranties for purchase when the ventilator is purchased. Please contact your local Covidien sales or service representative for addi- tional information.

• Page 12: Service Centers

  Here, you will find answers to frequently asked questions about the product and other Covidien products 24 hours a day, 7 days a week. If you require further assistance, contact your local Covidien representative.

• Page 13
  Service Centers Covidien France SAS Covidien Hong Kong Covidien ECE s.r.o. Covidien India C-Mill Gebouw K Unit 12 — 16, 18/F Magyarországi Fióktelepe 10th Floor Building No 9B Jan Campertstraat 21-A BEA Tower Mariássy u.7. DLF Cyber City Phase III Gurgaon…
• Page 14
  Preface Covidien Spain S.L. Covidien Sverige AB Covidien Switzerland Covidien Thailand C-Mill Gebouw K C-Mill Gebouw K C-Mill Gebouw K 99 Soi Rubia Jan Campertstraat 21-A Jan Campertstraat 21-A Jan Campertstraat 21-A Sukhumvit 42 Road 6416 SG Heerlen, Netherlands 6416 SG Heerlen, Netherlands 6416 SG Heerlen, Netherlands 13-14 Fl., Berli Jucker Building…

• Page 15: Safety Information

  1 Safety Information Definitions This manual uses three indicators to highlight critical information: warning, caution, and note. They are defined as follows: WARNING Indicates a condition that can endanger the patient or the ventilator operator. Caution Indicates a condition that can damage the equipment. Note Indicates points of particular emphasis, that make operation of the ventilator more efficient or con- venient.

• Page 16
  Safety Information WARNING: The ventilator must be used according to its intended use. Refer to section 2.1, Indications for Use. WARNING: Be aware this manual describes how to respond to the ventilator, but does not tell you how to respond to the patient.
• Page 17
  If the ventilator fails the alarm tests or if you cannot complete the tests, refer to Chapter 3, Alarms and Troubleshooting or call your equipment supplier or Covidien. WARNING: When an alarm condition is triggered, or there is evidence of a patient-ventilator fault or problem, examine the patient first before examining the ventilator.

• Page 18: Warnings Regarding Installation And Environment Of Use

  Safety Information WARNING: Do not connect the ventilator to any device other than a PC with a dedicated compatible Puritan Bennett™ software package. WARNING: The ventilator system is not intended to be a comprehensive monitoring device and does not activate alarms for all types of conditions.

• Page 19
  Warnings WARNING: To avoid damage to the ventilator, in particular the batteries or electrical components, fluids must not be allowed to enter the device, particularly through the air inlet filter or the cooling apertures located in the side, rear, and bottom panels of the ventilator. WARNING: To ensure correct and lasting operation of the device, ensure that the ventilator is installed and operated in the environmental conditions recommended in Appendix A, Specifications.
• Page 20
  60°C (140°F). This may lead to undesirable side effects for the patient. To avoid injury to the patient move the patient and the ventilator to a cooler location. For more information, contact Covidien. WARNING: The default setting for altitude compensation is YES. Altitude compensation should always be set to YES for accurate volume delivery calculations at all elevations.

• Page 21: Warnings Regarding Electrical Power Supplies

  Warnings WARNING: Exercise care to avoid any potential significant risks of reciprocal interference posed by the ventilator and accessories during specific investigations or treatments. Warnings Regarding Electrical Power Supplies 1.2.3 WARNING: The operator should connect the ventilator to an AC power source whenever available, for safer operation.

• Page 22: Warnings Regarding Hoses And Accessories

  Safety Information WARNING: Even if the internal battery charging indicator is off, charging of the battery may sometimes be incomplete if the ambient temperature is above 40°C (104°F) because of the battery’s internal heat safety device. WARNING: When the Low Battery alarm is triggered, immediately connect the ventilator to an AC power supply to maintain ventilation and recharge the internal battery.

• Page 23
  Warnings WARNING: The exhalation block is intended for single use by a single patient . It may periodically be cleaned, but it cannot be disinfected or sterilized. To maintain good measurement quality when used continuously, clean the exhalation block periodically (refer to section 7.3, Cleaning the Exhalation Block).
• Page 24
  (Max VTI), and minimum inspired volume (Min VTI) settings—must be periodically adjusted according to changes in the patient circuit resistance—especially when filters are replaced. WARNING: To ensure proper performance of the ventilator, use a patient circuit recommended by Covidien in this manual; refer to Chapter 4, Installation and Assembly…

• Page 25: Warnings Regarding Settings

  Ø 22 mm for adult patients, and a corrugated tube of Ø 15 mm for pediatric patients with a tidal volume lower than 200 ml. WARNING: To ensure proper performance of the ventilator, use only accessories (including oxygen accessories) approved and recommended by Covidien. See Appendix F, Parts and Accessories or contact your customer services.

• Page 26
  Safety Information WARNING: Ensure that the I Sens setting is not set to OFF when ventilating patients capable of triggering spontaneous breaths. WARNING: The ventilator offers a variety of breath delivery options. Throughout the patient’s treatment, the clinician should carefully select the ventilation mode and settings to use for that patient, based on clinical judgment, the condition and needs of the patient, and the benefits, limitations, and characteristics of the breath delivery options.
• Page 27
  Warnings WARNING: The Apnea alarm should be set to YES for ventilator dependent patients. WARNING: Setting any alarm limits to OFF or extreme high or low values can cause the associated alarm not to activate during ventilation, which reduces its efficacy for monitoring the patient and alerting the clinician to situations that may require intervention.

• Page 28: Warnings Regarding Pc Connection And Usb Memory Devices

  WARNING: To ensure proper servicing and avoid the possibility of physical injury to personnel or damage to the ventilator, only personnel authorized and qualified by Covidien should attempt to service or make authorized modifications to the Puritan Bennett™ 560 ventilator.

• Page 29
  Do not attempt to open, repair or otherwise service the ventilator yourself. Doing so might endanger the patient, damage the ventilator, or void your warranty. Only personnel authorized and qualified by Covidien should repair, open or service the ventilator. WARNING:…
• Page 30
  Safety Information WARNING: A patient treated by mechanical ventilation is highly vulnerable to the risks of infection. Dirty or contaminated equipment is a potential source of infection. Clean the ventilator and its accessories regularly and systematically before and after each use and following any maintenance procedure to reduce the risks of infection.

• Page 31: Warnings Regarding Oxygen

  Warnings WARNING: Connect the external electrical power source by first connecting the power cable to the ventilator and then to the external power source. Follow the reverse procedure to disconnect the device from electrical power sources. Warnings Regarding Oxygen 1.2.8 WARNING: The ventilator must not be used with flammable anesthetic substances.

• Page 32
  Safety Information WARNING: The hose connecting the ventilator to the oxygen source must be designed exclusively for use with medical-grade oxygen. Under no circumstances should the oxygen hose be modified by the user. In addition, the hose must be installed without the use of lubricants. WARNING: Ensure that the only gas supplied to the ventilator through the dedicated oxygen supply connector is medical-grade oxygen.

• Page 33: Warnings Regarding Electromagnetic Interference

  The use of any accessory other than those specified, with the exception of the power supplies or cables sold by Covidien, may lead to an increase in electromagnetic emissions or a decrease in the equipment protection against electromagnetic emissions. If the ventilator is used adjacent to such accessories or stacked with such devices, the ventilator’s performance should be monitored to verify normal…

• Page 34
  Safety Information Table 1-1.  Ventilator Symbols (Continued) Symbols Descriptions Insulation class II equipment (IEC 60417-5172). A regulatory standard classification for protection against electric shock. Class II equipment relies on double insulation rather than protective earthing. This symbol appears on the ventilator’s back panel; see item 5 in Table 1-2.  …
• Page 35
  Symbols and Markings Table 1-1.  Ventilator Symbols (Continued) Symbols Descriptions Exhalation valve pilot port. This symbol appears on the front right of the ventilator, adjacent to the exhalation valve and TO PATIENT ports, indicating the connection of the tubing between the patient circuit exhalation valve; see Figure 1-1, and item 3 in Figure 1-4.  …
• Page 36
  Safety Information Table 1-1.  Ventilator Symbols (Continued) Symbols Descriptions Inspiratory effort detected. This symbol appears in the front panel display’s Status window when the patient triggers a breath. Parameter adjustment bar. This graphic shows the current setting for parameters such as display contrast and alarm volume in the Pref- erences menu.
• Page 37
  Table 1-1.  Ventilator Symbols (Continued) Symbols Descriptions PC connection. This symbol indicates a port that can be used by authorized Covidien product service personnel or Covidien service personnel for software maintenance. See item 10 in Figure 1-3.   Atmospheric pressure limitations. See section for specifications.

• Page 38: Labels (Identification And Instruction Information)

  Safety Information Labels (Identification and Instruction Information) Various labels or specific markings are affixed to the ventilator that describe precautions to be taken for the correct use of the ventilator and contribute to the traceability of the product. See Table and the figures on the following pages for illustrations of these labels and markings and their loca- tions on the ventilator.

• Page 39: Figure 1-1. Locations Of Labels-Top-Front View

  Labels (Identification and Instruction Information) Note: The item number callouts in the following figures correspond to those listed in Table 1-2.   Figure 1-1.  Locations of Labels—Top-Front View Figure 1-2.  Locations of Labels—Front-Left View User Manual 1-25…

• Page 40: Figure 1-3. Location Of Labels And Markings-Rear View

  Safety Information Figure 1-3.  Location of Labels and Markings—Rear View Figure 1-4.  Location of Labels—Bottom View 1-26 User Manual…

• Page 41: Ventilator Overview

  2 Ventilator Overview Indications for Use The Puritan Bennett™ 560 Ventilator is indicated for the continuous or intermittent mechanical ventilatory support of patients weighing at least 11 lb (5 kg) who require mechanical ventilation. The ventilator is a restricted medical device intended for use by qualified, trained personnel under the direction of a doctor.

• Page 42: Target Operators

  Ventilator Overview Association), International Maritime Dangerous Goods code for sea and the European Agreement concerning the International Carriage of Dangerous Goods by Road (ADR) for Europe. Private individuals who transport the device are excluded from these regulations although for air transport some requirements apply.

• Page 43: Operational Use

  Operational Use Operational Use The Puritan Bennett™ 560 ventilator uses a micro-turbine to provide ventilatory support to patients. Clinicians may use a variety of interfaces to connect patients to the ventilator for continuous or intermittent ventilatory support. Some examples include mouthpieces; nasal masks or full face masks;…

• Page 44: Device Classification

  Ventilator Overview WARNING: Users must always possess an additional breathing circuit and exhalation valve while using the Puritan Bennett™ 560 ventilator. Device Classification The ventilator’s IEC/EN 60601-1classification is as follows: Protection/insulation class (electric shock): Class II • Protection index of enclosure: IP32 •…

• Page 45: Front Panel

  Front Panel Front Panel Figure 2-1.  Front Panel LCD display—Shows information about the ventilator, including Exhalation valve port—Nipple for providing piloting patient hours and software version, ventilation modes and settings, pressure to the exhalation valve. Controls the open-closed and monitored and calculated patient data and waveforms. The position of the exhalation valve.

• Page 46: Back Panel

  Ventilator Overview Back Panel Figure 2-2.  Back Panel Ergonomic carrying handle. PC cable connector: USB mini-B connector used for Puritan Bennett™ ventilator test software. WARNING: Do not connect the ventilator to any device other than a PC with a dedicated compatible Puritan Bennett™ soft- ware package.

• Page 47: Control Panel

  Control Panel Control Panel Figure 2-3.  Control Panel Alarm indicators (two LEDs): DOWN/FREEZE key: Red indicator: • Moves the cursor down and decreases parameter values. • Continuous: Very high priority (VHP) alarm activated. • During ventilation, freezes the waveform shown in the Wave- form menu.

• Page 48: Ventilation Menu

  Ventilator Overview Ventilation Menu Figure 2-4.  Ventilation Menu Display (on standby at left; during ventilation at right) 1 General information line: 2 Ventilation settings: 3 Preferences menu access line: Shows the current ventilation mode, Shows the specific ventilation parameter Highlight this line and press the along with the following: values for the currently selected ventilation ENTER…

• Page 49: Alarm Menu

  Alarm Menu Alarm Menu Figure 2-5.  Alarm Menu (on standby at left; during ventilation at right) 1 Title line: 2 Alarm settings: 3 Access line to Alarm Logs menu. Shows ventilation mode and the follow- Shows the specific alarm parameter Highlight this line and press the ENTER ing symbols: values for the currently selected ventila- key to show the Alarm Logs menu.

• Page 50: Waveforms Menu

  Ventilator Overview Waveforms Menu 2.10 The display of waveforms (see Figure 2-6) is optional and can be selected using the Menu key. The Waveform menu is only accessible when ventilation is active. Figure 2-6.  Waveforms Menu 1 Title line: 2 Graphic zone: 3 Numeric zone: Shows ventilation mode and the follow- Shows the patient’s pressure and flow…

• Page 51: Usb Memory Device Menu

  Keep in mind that troubleshooting information is available in this manual to assist you in the event of a problem. See Chapter 3, Alarms and Troubleshooting. If you cannot determine the cause of a problem, contact your equipment supplier or Covidien. See section 8.7, Service Assistance.

• Page 52
  Ventilator Overview Page Left Intentionally Blank 2-12 User Manual…

• Page 53: Alarms And Troubleshooting

  3 Alarms and Troubleshooting Overview The alarms or faults generated by the Puritan Bennett™ 560 ventilator are classified into two cat- egories: Ventilation (or utilization) alarms • Technical faults • Alarms indicate events likely to affect the ventilation in the short term and necessitate rapid inter- vention (see section 3.9, Troubleshooting).

• Page 54: Alarm Level Of Priority

  Alarms and Troubleshooting Note: Default alarm setting preferences should be entered prior to using the ventilator. Note: All configurable alarm settings are recorded in the ventilator’s nonvolatile internal memory, and are retained when powering down or in the event of a total loss of power. Alarm Level of Priority The alarm hierarchy for signaling the level of alarm criticality is listed as follows: Very high priority (VHP): Immediate critical situation;…

• Page 55: Alarm Display

  Alarm Display Alarm Display Note: The alarm indicator LEDs to the left of the ALARM CONTROL key on the Puritan Bennett™ 560 ventilator are designed to be visible to the operator at any position where the ventilator is visible to the operator. Specific alarm detail (shown in the alarm message area) is designed to be readable from up to four meters from the screen, at a viewing angle of up to 30°.

• Page 56: Alarm Logs Menu

  Alarms and Troubleshooting Note: When an alarm is triggered, if the current menu shown is not the Ventilation parameters or Alarm menu, the display automatically switches to one of these menus to show the alarm message. Note: In the event several alarms are activated at the same time, the highest priority audible and visual alarm is highlighted;…

• Page 57: Figure 3-4. Alarm Logs Screen

  Alarm Logs Menu Figure 3-4.  Alarm Logs Screen Note: When no alarm has been activated, the message “NO DATA” is shown on the screen (see Figure 3-5). Figure 3-5.  Alarm Logs Screen (no alarm activated) For more information on the User’s clear alerts line, see section 3.7, Reactivating Alarms.

• Page 58: Pausing The Audible Portion Of Alarms

  Alarms and Troubleshooting Pausing the Audible Portion of Alarms WARNING: Do not pause, disable, or decrease the volume of the ventilator’s audible alarm if patient safety could be compromised. To pause the audible portion of activated alarms for 60 seconds at a time, press the ALARM CONTROL key.

• Page 59: Pausing And Resetting Alarms

  Pausing and Resetting Alarms Pausing and Resetting Alarms WARNING: Alarm volume should be adjusted with respect to the ventilator’s operating environment and so that the patient’s caretakers can hear the alarms. The audible alarm vents located at the front of the device should never be obstructed.

• Page 60: Reactivating Alarms

  Alarms and Troubleshooting Reactivating Alarms Alarms that have been paused and whose activation conditions continue to exist can be reactivated. To reactivate alarms, proceed as follows: Press the MENU key to access the alarm setting menu, if this is not the menu currently shown. Press the DOWN key to position the cursor on the Alarm Logs line, if this is not already the case.

• Page 61: Overview Of Alarms

  Overview of Alarms The messages of all active alarms are shown in a loop in the Ventilation and Alarm menus. • The audio paused symbol disappears (if it was shown). • The alarm paused symbol disappears. • Overview of Alarms Note: The message: “*IF PERSISTS RESTART/SRVC”…

• Page 62
  Alarms and Troubleshooting Table 3-1.  Overview of Alarms (Continued) Alarm message Cause/ventilator response Priority Audio Paused Alarm Paused available available BUZZER FAULT3 Battery charge failure due to incorrect voltage. Contact your service representative for assistance. RESTART/SRVC BUZZER LOW BATTERY Buzzer battery failure. The battery buzzer voltage is too low.
• Page 63
  Overview of Alarms Table 3-1.  Overview of Alarms (Continued) Alarm message Cause/ventilator response Priority Audio Paused Alarm Paused available available CHECK SETTINGS Alarm activation occurs: • Systematically after software versions have changed. • Loss of memorized parameters Consequence: • Locking key disabled •…
• Page 64
  Alarms and Troubleshooting Table 3-1.  Overview of Alarms (Continued) Alarm message Cause/ventilator response Priority Audio Paused Alarm Paused available available EMPTY BATTERY Internal battery capacity <10 minutes or 3%. (battery If AC power is voltage <22.5 V) not connected: Consequence: Ventilation comes to a halt. If AC power is connected: LP EXH VALVE LEAKAGE…
• Page 65
  Overview of Alarms Table 3-1.  Overview of Alarms (Continued) Alarm message Cause/ventilator response Priority Audio Paused Alarm Paused available available INSP FLOW Inspiratory flow is constant (±1 lpm) with normal turbine temperature and speed conditions. Contact RESTART/SRVC your service representative for assistance. INTENTIONAL VENT STOP Ventilation has been stopped voluntarily by the care- giver or patient.
• Page 66
  Alarms and Troubleshooting Table 3-1.  Overview of Alarms (Continued) Alarm message Cause/ventilator response Priority Audio Paused Alarm Paused available available PATIENT DISCONNECTION* Alarm activation occurs under the following condi- tions (time is in seconds): *IF PERSISTS RESTART/SRVC • Disconnection time or 60/R-Rate, whichever is great- er, in P A/C and V A/C mode •…

• Page 67: Troubleshooting

  WARNING: To ensure proper servicing and avoid the possibility of physical injury to personnel or damage to the ventilator, only personnel authorized and qualified by Covidien should attempt to service or make authorized modifications to the Puritan Bennett™ 560 ventilator.

• Page 68
  Alarms and Troubleshooting Table 3-2.  Alarms and Corrective Actions Alarm message or Possible reason for the alarm event Corrective action symptom AC POWER DISCONNECTION AC (“mains”) power source cut off. Cancel the alarm, and then check the supply cable and the effective availability of a voltage on the AC power (“mains”) port.
• Page 69
  Troubleshooting Table 3-2.  Alarms and Corrective Actions (Continued) Alarm message or Possible reason for the alarm event Corrective action symptom CALIBRATION FAIL Too large a difference between a calibration point There may be a leak in the circuit. Ensure an approved and its tolerance range. circuit is in use (see circuit documentation).
• Page 70
  Alarms and Troubleshooting Table 3-2.  Alarms and Corrective Actions (Continued) Alarm message or Possible reason for the alarm event Corrective action symptom CHECK PROXIMAL LINE1* No connection of the proximal pressure tube Reconnect the proximal pressure line. when ventilation starts. *IF PERSISTS RESTART/SRVC Note: The Check Proximal Proximal pressure line disconnected or obstruct- Reconnect the connection line or replace it if…
• Page 71
  Troubleshooting Table 3-2.  Alarms and Corrective Actions (Continued) Alarm message or Possible reason for the alarm event Corrective action symptom DEVICE FAULT7 Internal technical problem. Restart ventilator to see if alarm clears. If not, replace the ventilator. Contact your customer service representa- IF PERSISTS RESTART/SRVC tive for assistance.
• Page 72
  Alarms and Troubleshooting Table 3-2.  Alarms and Corrective Actions (Continued) Alarm message or Possible reason for the alarm event Corrective action symptom SENSOR MISSING There is no FiO sensor, and FiO alarms are active. Contact your customer service representative for assis- tance. HIGH FiO The level of oxygen being delivered to the patient Contact your customer service representative for assis-…
• Page 73
  Troubleshooting Table 3-2.  Alarms and Corrective Actions (Continued) Alarm message or Possible reason for the alarm event Corrective action symptom HIGH LEAKAGE The leak estimated by the ventilator exceeds the Readjust mask to reduce leakage. Max Leak alarm threshold. Contact your customer service representative for addi- tional assistance.
• Page 74
  Alarms and Troubleshooting Table 3-2.  Alarms and Corrective Actions (Continued) Alarm message or Possible reason for the alarm event Corrective action symptom HIGH VTI Adjustment of the Max VTI level too low (for PSV, Contact your customer service representative for assis- CPAP, P A/C, P SIMV, and V SIMV modes). tance.
• Page 75
  Troubleshooting Table 3-2.  Alarms and Corrective Actions (Continued) Alarm message or Possible reason for the alarm event Corrective action symptom LOW VTE Patient circuit obstructed. Clean, unblock, or properly connect the patient circuit. Leak in the patient circuit. Check and properly connect the patient circuit connec- tions.
• Page 76
  Alarms and Troubleshooting Table 3-2.  Alarms and Corrective Actions (Continued) Alarm message or Possible reason for the alarm event Corrective action symptom PATIENT DISCONNECTION Adjustment of Min PIP too high. Contact your customer service representative for assis- tance. *IF PERSISTS RESTART/SRVC Leak or loose connection in the patient circuit. Check the patient circuit connections to the ventilator;…

• Page 77: Additional Troubleshooting

  Troubleshooting Table 3-2.  Alarms and Corrective Actions (Continued) Alarm message or Possible reason for the alarm event Corrective action symptom VALVE MISSING CONNECT The ventilation settings are not compatible with Connect exhalation valve. VALVE the type of patient circuit used. VTI NOT REACHED Defective inspiratory flow sensor or internal leak of Restart ventilator to see if alarm clears.

• Page 78
  Alarms and Troubleshooting Table 3-3.  Additional Troubleshooting and Corrective Actions (Continued) Conditions Possible causes Corrective actions Unusual display on the Problem with the display unit. Ensure that the ventilator is not exposed to direct screen radiation from the sun. Contact your customer service representative if the problem persists.

• Page 79: Installation And Assembly

  4 Installation and Assembly WARNING: Before operating the ventilator, read, understand, and strictly follow the information contained in Chapter 1, Safety Information. WARNING: A patient treated by mechanical ventilation is highly vulnerable to the risks of infection. Dirty or contaminated equipment is a potential source of infection. Clean the ventilator and its accessories regularly and systematically before and after each use and following any maintenance procedure to reduce the risks of infection.

• Page 80
  60°C (140°F). This may lead to undesirable side effects for the patient. To avoid injury to the patient move the patient and the ventilator to a cooler location. For more information, contact Covidien. WARNING: To reduce the risk of a fire hazard, keep matches, lighted cigarettes, and all other sources of ignition (such as flammable anesthetics and/or heaters) away from the ventilator and oxygen hoses.

• Page 81: Connecting To External Ac Power

  The use of any accessory other than those specified, with the exception of the power supplies or cables sold by Covidien, may lead to an increase in electromagnetic emissions or a decrease in the equipment protection against electromagnetic emissions. If the ventilator is used adjacent to such accessories or stacked with such devices, the ventilator’s performance should be monitored to verify normal…

• Page 82: Figure 4-1. The Power Cable Holder

  Installation and Assembly WARNING: Do not leave power cables lying on the ground where they may pose a hazard. To prevent accidental disconnection of the AC power cable, use the power cable holder that is inserted into the notch on the battery cover. See Figure 4-1. Figure 4-1.  The Power Cable Holder Power cable holder Notch on battery cover…

• Page 83: Figure 4-3. Power Cable Connected To The Ventilator

  Connecting to External AC Power Connect the female end of the ventilator’s AC power cable to the AC connector on the back of the ven- tilator. Figure 4-3.  Power Cable Connected to the Ventilator Connect the male end of the AC power cable to the AC power outlet. The AC power indicator on the top left corner of the ventilator illuminates.

• Page 84: Connecting To An External Dc Power Source

  Installation and Assembly To disconnect the AC power cable: Disconnect the AC power cable from the AC power outlet. Disconnect the AC power cable from the ventilator’s AC connector at the rear of the device. Grasp the AC power cable at the level of the power cable holder and turn the cable clockwise while lifting it upwards and out of the holder.

• Page 85: Figure 4-5. Connecting The Dc Power Cable To The Ventilator

  Connecting to an External DC Power Source Figure 4-5.  Connecting the DC Power Cable to the Ventilator Red alignment dots Connector locking ring DC power cable connector To connect the DC power cable to the ventilator (see Figure 4-5): Line up the red alignment dots on the ventilator’s DC power receptacle and on the DC power cable. Push the DC power cable into the ventilator’s DC power receptacle.

• Page 86: Patient Circuit

  Installation and Assembly Connect the smaller connector on the DC power cable into the DC power input receptacle on the rear of the ventilator. Connect the larger connector on the DC power cable into the power source’s DC auxiliary receptacle. If connecting the ventilator to the Puritan Bennett™…

• Page 87: Choosing The Patient Circuit Type

  WARNING: To ensure proper performance of the ventilator, use a patient circuit recommended by Covidien in this manual; refer to Chapter 4,…

• Page 88: Figure 4-7. Single-Limb Patient Circuit With Exhalation Valve (Including Accessories)

  Installation and Assembly Single-Limb Circuit (With Exhalation Valve) Figure 4-7.  Single-Limb Patient Circuit With Exhalation Valve (including accessories) Inspiratory bacteria filter Exhalation valve tubing Short circuit tubing Proximal pressure tubing Humidifier (optional accessory) Patient proximal pressure port Water trap Exhalation valve port Exhalation valve FROM PATIENT port Note:…

• Page 89: Figure 4-8. Closeup Of Exhalation Valve Tube And Proximal Pressure Tube

  Patient Circuit Connect the exhalation valve tubing to the exhalation valve port on the ventilator. See Figure for a detailed view. Figure 4-8.  Closeup of Exhalation Valve Tube and Proximal Pressure Tube TO PATIENT port Proximal pressure tube Exhalation valve tube Connect the inspiratory bacteria filter to the TO PATIENT outlet port on the ventilator. Connect one end of the short circuit tubing to the inspiratory bacteria filter.

• Page 90: Figure 4-9. Double-Limb Patient Circuit (Including Accessories)

  Installation and Assembly Double-Limb Circuit Figure 4-9.  Double-Limb Patient Circuit (including accessories) Inspiratory bacteria filter Exhalation valve tubing Humidifier (optional accessory) Exhalation valve assembly Water traps Exhalation (FROM PATIENT) port Short circuit tubing Exhalation bacteria filter Patient wye Patient proximal pressure port Proximal pressure tubing Exhalation valve port Double-limb circuit tubing…

• Page 91: Figure 4-10. Closeup Of Exhalation Valve Tube And Proximal Pressure Tube

  Patient Circuit Connect the proximal pressure tubing to the patient proximal pressure port on the ventilator. See Figure 4-10 for a detailed view. Connect the exhalation valve assembly to the exhaled gas outlet on the left side of the ventilator, near the left front corner.

• Page 92: Figure 4-11. Close-Up Of Exhalation Bacteria Filter Connection

  Installation and Assembly Using a circuit adapter, connect the exhalation bacterial filter to the FROM PATIENT inlet port. See Figure 4-11. Figure 4-11.  Close-up of Exhalation Bacteria Filter Connection Single-Limb Circuit (Without Exhalation Valve) Figure 4-12.  Single-Limb Patient Circuit Without Exhalation Valve Inspiratory bacteria filter Short circuit tubing Humidifier (optional accessory) Patient circuit tubing…

• Page 93
  Patient Circuit Connect the inspiratory bacteria filter to the TO PATIENT outlet port on the ventilator. Connect one end of the short circuit tubing to the inspiratory bacteria filter. Connect the other end of the short circuit tubing to the inlet port of the humidifier. If it is not already in place, connect a water trap to the outlet port of the humidifier and to the patient circuit tubing.

• Page 94: Filters

  Installation and Assembly WARNING: Adding accessories to the ventilator breathing circuit, such as a humidifier and water trap(s), may result in a decrease in tidal volume delivered to the patient due to the added compressible volume of the accessory. Always assure that the patient is receiving the appropriate inspired volume when altering the breathing circuit configuration.

• Page 95: Bacteria Filter

  Filters WARNING: Failing to replace a dirty air inlet filter, or operating the ventilator without a filter, may cause serious damage to the ventilator. Bacteria Filter 4.5.2 It is highly recommended that you install a bacteria filter (see Figure 4-14) on both single- and double-limb circuits.

• Page 96: Humidifier

  Installation and Assembly Humidifier The humidifier (Figure 4-15) adds moisture (water vapor) and warms the gas in the patient circuit. It is inserted into the patient circuit between the TO PATIENT outlet port and the patient (see Figures 4-7, 4-9, and 4-12). Figure 4-15.  Humidifier WARNING: During invasive ventilation (when an artificial airway bypasses the patient’s upper respiratory system),…

• Page 97: Exhalation Block

  Exhalation Block See the humidification device’s instructions for information on operating, cleaning, and sterilizing the humidifier. Note: It is the user’s responsibility to verify that any humidification system selected for use is compatible with the Puritan Bennett™ 560 ventilator. Exhalation Block WARNING: The exhalation block is intended for single use by a single patient .

• Page 98: Oxygen

  Installation and Assembly Oxygen Administering Oxygen 4.8.1 WARNING: The ventilator must not be used with flammable anesthetic substances. WARNING: Oxygen therapy for patients with respiratory failure is a common and effective medical prescription. However, be aware that inappropriate oxygen use may potentially lead to serious complications, including, but not limited to, patient injury.

• Page 99: Connecting The Oxygen Supply

  Oxygen Connecting the Oxygen Supply 4.8.2 WARNING: Ensure that the only gas supplied to the ventilator through the dedicated oxygen supply connector is medical-grade oxygen. WARNING: The hose connecting the ventilator to the oxygen source must be designed exclusively for use with medical-grade oxygen.

• Page 100: Figure 4-18. Connecting The Oxygen Supply

  Installation and Assembly WARNING: Before connecting the oxygen supply, ensure that the stud on the oxygen inlet (Figure 4-17, item 3) is protruding outwards. WARNING: Inspect the oxygen coupler (Figure 4-17, item 2) before use to ensure it has its black O-ring (Figure 4-18, item 2) attached and in good condition.

• Page 101: Figure 4-19. Disconnecting The Oxygen Supply

  Oxygen Figure 4-19.  Disconnecting the Oxygen Supply Disconnect the oxygen supply by pulling the coupler out from the inlet port. The locking stud on the inlet port (Figure 4-18, item 4) will then extend outwards, which is required before the oxygen connector can be reconnected. WARNING: The coupler must not remain connected to the oxygen connector unless it also connected to a leak- proof, external oxygen gas source.

• Page 102: Figure 4-20

  Installation and Assembly Note: When using a new sensor, allow its temperature to become stable for about 20 minutes in ambient air before installing it, calibrating it, and starting ventilation. Note: A clinician or medical professional should be present when calibrating the FiO sensor.

• Page 103: Using The Dual Bag

  Using the Dual Bag Using the Dual Bag The dual bag accessory allows the patient to carry the Puritan Bennett™ 560 ventilator on his or her back, and also allows it to be secured to the back of a wheelchair or to the seat of a personal vehicle. WARNING: Due to the internal battery’s limited reserve capacity, the ventilator should only be operated on the internal battery when no other power source is available.

• Page 104: Wearing The Dual Bag As A Backpack

  Installation and Assembly Slip the ventilator into the dual bag, front panel first. Push it in completely to ensure a snug fit. Shut the rear panel of the dual bag ensuring that the hook and loop fastener strips are securely fastened. If not mounting the dual bag on a wheelchair or in a personal vehicle, the patient circuit can be reconnected to the ventilator.

• Page 105: Figure 4-22

  Using the Dual Bag Figure 4-22.  Using the Dual Bag on a Wheelchair (with double-limb circuit on left; with single-limb circuit on right) To secure the dual bag onto a wheelchair with two push handles (see Figure 4-22): Facing the back of the wheelchair, loop each backpack strap over one of the push handles. Attach the nonadjustable side of the maintaining belt to the side clip of the dual bag.

• Page 106: Securing The Ventilator In A Personal Vehicle

  Installation and Assembly Securing the Ventilator in a Personal Vehicle 4.9.4 Figure 4-23.  Using the Dual Bag in a Personal Vehicle To secure the dual bag in a personal vehicle (see Figure 4-23): Unclip the two backpack straps from the side clips. Clip the suspension onto the central ring.

• Page 107: Mounting The Ventilator On A Utility Cart

  Mounting the Ventilator on a Utility Cart Mounting the Ventilator on a Utility Cart 4.10 As an alternative to using the dual bag for patient mobility, the Puritan Bennett™ 560 ventilator can be mounted on a utility cart. To mount the ventilator on the cart: Match the mounting holes on the bottom of the ventilator to the mounting studs on the top of the utility cart platform.

• Page 108: Figure 4-26. Puritan Bennett™ 560 Ventilator Mounted On Utility Cart

  Installation and Assembly Figure 4-26.  Puritan Bennett™ 560 Ventilator Mounted on Utility Cart 4-30 User Manual…

• Page 109: Operating Procedures

  5 Operating Procedures Turning on the Ventilator WARNING: Before operating the ventilator, read, understand, and strictly follow the information contained in Chapter 1, Safety Information. WARNING: If the ventilator has been transported or stored at a temperature that differs more than 20°C (36°F) from the temperature in which it will be operating, the ventilator should be allowed to stabilize in its operating environment for at least 2 hours prior to use.

• Page 110: Figure 5-1. Turning On The Ventilator

  If the ventilator fails the alarm tests or if you cannot complete the tests, refer to section 3.9, Troubleshooting or call your equipment supplier or Covidien. WARNING: Due to the internal battery’s limited reserve capacity, the ventilator should only be operated on the internal battery when no other power source is available.

• Page 111: Figure 5-2. Ventilation On/Off Button And Standby Indicator

  Turning on the Ventilator The following events occur: The ventilator is turned on. • A Power On Self Test (POST) is carried out (when plugged in to an AC power source). • The front panel indicators flash (except for the indicator showing the type of power supply in use, which •…

• Page 112: Usb Menu Parameters

  Only one USB memory device may be connected at any time; otherwise, an error message will be shown. To access patient data via a PC, the Puritan Bennett™ Respiratory Insight software package is avail- able for clinicians. Contact Covidien or your product representative for further information. User Manual…

• Page 113: Usb Memory Device Specifications

  USB Menu Parameters USB Memory Device Specifications 5.2.1 Table 5-1.  USB Memory Device Specifications Characteristics Supported formats USB compatibility USB flash memory USB 2.0 or USB 1.1, 32 bit format Number of files Maximum 999 (sector size: 512-2048 bytes) USB size 128 MB to 4GB (to guarantee accuracy of transfer time, at least 10% of the USB memory device capacity must be free) USB Memory Device Menu 5.2.2…

• Page 114: Figure 5-6. Selecting Transfer Continuously

  Operating Procedures The following data will be recorded to the USB memory device: Monitoring: Pressure, inspired flow, exhaled flow and leak waveforms • Trends: Leaks, VTI, VTE, Rate, I:E, M. Vol, PIP, and PEEP measurements • The data can be accessed by a doctor or service provider using the Puritan Bennett™ Respiratory Insight software package.

• Page 115: Figure 5-7. Selecting Transfer Trends

  USB Menu Parameters Note: Other functions of the USB memory device are not available during continuous recording. Note: If the memory capacity on the USB memory device is insufficient the message “TRANSFER NOT ALLOWED — USB CAPACITY INSUFFICIENT” is shown and data transfer is not allowed. Delete the data on the USB memory device before restarting data transfer.

• Page 116
  Operating Procedures Press ENTER to confirm the new parameter setting. The new parameter setting is shown continuously. • The cursor is placed at the STOP position. • To manually stop trend transfer, press ENTER. If a parameter change is not confirmed by pressing ENTER before 7 seconds elapse, the ventilator resets the parameter to its previous value.

• Page 117: Starting Ventilation

  Starting Ventilation Starting Ventilation Before starting ventilation, see Appendix C, Operational Verification Checklist, and set the parameter values in the Preferences menu. WARNING: Verify the functionality of the alarms before connecting the patient to the ventilator. WARNING: Before starting ventilation, ensure that the device is properly assembled and that the air inlet, cooling vents, and alarm sound diffusion holes are not obstructed.

• Page 118: Stopping Ventilation

  Operating Procedures Figure 5-9.  Starting Ventilation Stopping Ventilation WARNING: Do not allow a patient to remain connected to the ventilator when ventilation is stopped, because a substantial quantity of expiratory gas, primarily carbon dioxide, may be inhaled by the patient. In some circumstances, inhaling carbon dioxide may lead to under-ventilation, suffocation, and serious injury or death.

• Page 119: Turning Off The Ventilator

  Turning Off the Ventilator Figure 5-11.  Stopping Ventilation (2) A double beep sounds. • Release the VENTILATION ON/OFF button. Press the VENTILATION ON/OFF button again within 5 seconds to confirm stop, otherwise ventilation will continue. Ventilation stops. • The blue LED located to the upper right of the VENTILATION ON/OFF button (Figure 5-9, item 2) illumi- •…

• Page 120
  Operating Procedures Note: A continuous alarm condition will be activated if the ventilator power switch is turned off while ventilation is in progress. When the power switch is turned back on again, the ventilation will resume without having to press the VENTILATION ON/OFF button.

• Page 121: Internal Battery

  6 Internal Battery WARNING: Even though the Puritan Bennett™ 560 ventilator meets current safety standards, the internal Lithium-ion battery of the device exceeds the 100Wh threshold and is therefore considered to be Dangerous Goods (DG) Class 9 – Miscellaneous, when transported in commerce. As such, the Puritan Bennett™…

• Page 122: Battery Capacity

  Internal Battery Battery Capacity The reserve capacity offered by the internal battery depends on the level of ventilation parameters, the environmental conditions (primarily in terms of temperature) and the physiological character- istics of the patient. With a fully charged battery at a normal room temperature of 25°C (±5°C), the ventilator can be expected to operate on internal battery power for the average durations shown in Table 6-1.  …

• Page 123: Battery Operation

  Battery Operation Battery Operation WARNING: Before using the ventilator’s internal battery, ensure that the battery is fully charged and that the charge holds. Back up ventilators or those in storage should be connected to an AC power source to protect the integrity of the battery. Note: Buzzer and battery alarms may occur when the unit is first powered on after the internal battery has been completely drained.

• Page 124: Figure 6-2. Battery Reserve Capacity As A Percentage

  Internal Battery If ventilation is stopped, the internal battery reserve capacity is shown as a percentage of battery charge. See Figure 6-2.   Figure 6-2.  Battery Reserve Capacity as a Percentage If the ventilator is running, the internal battery reserve is momentarily shown as a percentage. Then, after the ventilator calculates the battery time remaining (which takes about 2 minutes, depending on the power consumption of the ventilator), the internal battery reserve is then shown in hours and minutes (rounded to the nearest 10 minutes).

• Page 125: Testing The Battery

  Testing the Battery In the final discharge phase, the Empty Battery alarm will become continuous, and ventilation may be interrupted at any time during this phase. Note: The Empty Battery alarm symbol may disappear shortly before the ventilator completely stops, but it always triggers a final, continuous alarm.

• Page 126: Storage

  Internal Battery WARNING: Even if the internal battery indicator is off, charge of the battery may sometimes be incomplete regardless of charge time when the ambient temperature is above 40°C (104°F). This is due to the characteristics of the battery’s internal heat safety device. Although it is not necessary to start the ventilator to charge the battery, charging the battery during operation will increase the time required to fully charge the internal battery.

• Page 127: Cleaning

  7 Cleaning WARNING: A patient treated by mechanical ventilation is highly vulnerable to the risks of infection. Dirty or contaminated equipment is a potential source of infection. Clean the ventilator and its accessories regularly and systematically before and after each use and following any maintenance procedure to reduce the risks of infection.

• Page 128: Cleaning The Accessories

  Cleaning To clean the surface of the ventilator: Dip a clean, soft cloth into a mixture of mild soap and water, or other approved cleaning solution. For a list of approved cleaning solutions, see Table 7-1.   Table 7-1.  Approved Cleaning Solutions for Exterior Ventilator Surfaces Description Mild dishwashing detergent 70% isopropyl alcohol (rubbing alcohol)

• Page 129: Cleaning The Exhalation Block

  Cleaning the Exhalation Block Cleaning the Exhalation Block WARNING: The exhalation block is intended for single use by a single patient . It may periodically be cleaned, but it cannot be disinfected or sterilized. To maintain good measurement quality when used continuously, clean the exhalation block periodically.

• Page 130: Pneumatic System

  Cleaning Pneumatic System This section describes the components of the pneumatic system. Figure shows a pneumatic block diagram of the Puritan Bennett™ 560 Ventilator, including the patient circuit. The main pneumatic components that can potentially get contaminated during use are the air inlet filter (2); low pressure oxygen inlet /valve (36); oxygen solenoid valve (37); inlet and outlet silencers (not shown);…

• Page 131
  Pneumatic System Humidifier, nebulizer, or additional water traps (not shown) Power supply (located above power management PCBA) Inspiratory tubing Power switch Proximal pressure tube AC input Patient wye DC input Inspiratory pressure sensor PC port Proximal pressure sensor Type A USB ports (2) Exhalation valve pilot tube port (not used) Buzzer PCBA…
• Page 132
  Cleaning Page Left Intentionally Blank User Manual…

• Page 133: Routine Maintenance

  Do not attempt to open, repair or otherwise service the ventilator yourself. Doing so might endanger the patient, damage the ventilator, and/or void your warranty. Only personnel authorized and qualified by Covidien should repair, open or service the ventilator. WARNING: Ensure that the ventilator is powered off and not in use before performing routine maintenance.

• Page 134: Calibrating The Exhalation Flow Sensor

  Routine Maintenance Calibrating the Exhalation Flow Sensor Each time the exhalation block or circuit is removed and reinstalled or after installing a new exhala- tion block, the exhalation flow sensor must be recalibrated before using the ventilator. This process is automatic and does not require the use of a measurement device. Note: Perform calibration with either an adult or pediatric circuit.

• Page 135
  Calibrating the Exhalation Flow Sensor Figure 8-2.  Calibrating the Exhalation Flow Sensor (1) Press the UP or DOWN key. “YES” is shown instead of “OFF”. Figure 8-3.  Calibrating the Exhalation Flow Sensor (2) Press the ENTER key to start calibration. The message “…Exp. calib. Processing…” is shown in the window on the right while calibration is in •…

• Page 136: Calibrating The Fio2 Sensor

  Routine Maintenance A short beep sounds to confirm the second adjustment. • This process continues until adjustments are complete for all eight calibration points. • Note: The exhalation flow sensor calibration procedure, once initiated, must run to its conclusion. Note: No message is shown when the ventilator passes calibration;…

• Page 137
  Calibrating the FiO2 Sensor Press the ENTER key twice to access the Patient column (central column) of the FiO setup line. “OFF” flashes in the central column. • “OFF” flashes in the window on the right. • The message “FiO Calibration?”…

• Page 138: Replacing The Air Inlet Filter

  Routine Maintenance Figure 8-7.  Calibrating the FiO Sensor (3) A short beep sounds to confirm that the FiO sensor has been calibrated. • Press the ENTER key to exit the FiO setup line. Note: The FiO sensor calibration procedure, once initiated, must run to its conclusion. In the event of calibration errors, the following events occur: An alarm is activated and the message “FiO CALIBRATION FAIL”…

• Page 139: Figure 8-8. Replacing The Air Inlet Filter

  Replacing the Air Inlet Filter Figure 8-8.  Replacing the Air Inlet Filter To replace the air inlet filter (see Figure 8-8): Hold the filter between your fingers (view 1). Remove the filter (view 2) and discard it as instructed by the responsible organization. WARNING: Contact local authorities to determine the proper method to dispose of potentially hazardous parts and accessories.

• Page 140: Recommended Schedule Of Maintenance

  Routine Maintenance Recommended Schedule of Maintenance Preventive Maintenance Intervals 8.6.1 Table lists the periodic maintenance activities required for the Puritan Bennett™ 560 Ventilator. Total machine hours appear on the welcome screen that appears when turning on the ventilator with the power switch, in the Preferences menu during normal operation, and also when entering maintenance mode.

• Page 141
  For all additional accessories not necessarily considered as consumables consult the manufacturer’s recommendations. Note: To prevent any risk of cross contamination, Covidien recommends the use of DAR™ filters (Ref: 351/5856 or equivalent) to protect the patient outlet port and the exhalation block port. User Manual…

• Page 142: Maintenance Of The Internal Battery

  Routine Maintenance Failure to observe these recommendations may result in a loss of performance, excessive overheat- ing, a loss of certain functions and, in the long term, compromise the longevity of the ventilator. Maintenance of the Internal Battery 8.6.2 The internal battery does not need to be removed to verify its correct operation. Periodic Test of the Internal Battery 8.6.3 The ventilator continuously and automatically checks the state of the internal battery, even when…

• Page 143: Service Assistance

  In the event of a problem with the ventilator, see Chapter 3, Alarms and Troubleshooting. If you cannot determine the cause of the problem, contact your equipment supplier or Covidien. For more information and local Covidien Technical Service contact details, see Service Centers in the Preface.

• Page 144
  Routine Maintenance Page Left Intentionally Blank 8-12 User Manual…

• Page 145: Specifications

  A Specifications Physical Table A-1.  Physical Description (excluding accessories) Ventilator weight 9.9 lb. (4.5 kg) Ventilator dimensions 9.25 in wide x 12.40 in deep x 6.0 in high (235 mm wide x 315 mm deep x 154 mm high) Connectors Inspiratory limb connector: ISO 22 mm (OD) conical Exhalation limb connector (on exhalation block): ISO 22 mm (ID) conical Oxygen inlet: female connector with valve Device airway volume…

• Page 146: Indicators And Alarms

  Specifications Table A-3.  Internal Lithium Ion Battery Voltage 25.2 VDC Full-load capacity 4.8 Ah On standby: 1.5 Ah Ampere-hour rating During ventilation: 0.5 Ah Watt hour rating 124 Wh to 126 Wh Standby mode: 1.5 A/hr. (duration: <6 hr.) Charging current Ventilation mode: 0.5 A/hr. (duration: <13 hr.) Average operating time at 25°C (±5°C) with a fully charged battery (having less than 50 charge/discharge cycles) at the following displayed values: Vt = 200 ml (±5 ml), PIP = 10 mbar (±2 mbar), Rate = 20 bpm…

• Page 147: Performance

  Performance Performance Note: Performance specifications listed are applicable when dry gases are used in the patient system. Table A-7.  Performance Parameter Specifications and Tolerances Settings Range Tolerances Volume 50 to 2000 ml ±(10 ml +15%) Pressure 5 to 55 mbar ±(1 mbar +10%) Time 0.3 to 6.0 s ±10%…

• Page 148: Range, Resolution, And Accuracy

  Specifications Table A-8.  Monitored Parameter Tolerances (Continued) Ventilator parameter Tolerances Inspiratory Minute Volume (M VoI) ±(10 mL +15% VTI) ×Rate (with exhalation valve) and ±(20 mL +20% VTI) ×Rate in NIV configuration (without exhalation valve) Vt Sigh ±(20ml +20%) ±(2.5% +2.5% FiO Leak ±(3 lpm +20%) Apnea Index (AI)

• Page 149
  Range, Resolution, and Accuracy Table A-9.  Ventilator Range, Resolution, and Accuracy (Continued) Ventilator settings Range, resolution, and accuracy Pressure support Range: OFF or 5 mbar to 55 mbar in valve configuration (P Support) Range: 6 mbar to 30 mbar in leak configuration Resolution: 1 mbar Accuracy: ±(1 mbar +10%) of P Support + PEEP setting Default value: 15 mbar…
• Page 150
  Specifications Table A-9.  Ventilator Range, Resolution, and Accuracy (Continued) Ventilator settings Range, resolution, and accuracy Ramp Range: Square (SQ), descending ramp (D), sinusoidal (S) (Flow Pattern) Resolution: N/A Default value: Descending ramp (D) In V SIMV, flow pattern is set to square and is not adjustable PEEP Range: OFF (0.5 mbar) to 20 mbar Resolution: 1 mbar…
• Page 151
  Range, Resolution, and Accuracy Table A-9.  Ventilator Range, Resolution, and Accuracy (Continued) Ventilator settings Range, resolution, and accuracy Maximum Exhaled Tidal Volume Range: 80 mL to 3000 mL (Max VTE) Resolution: 10 mL Default value: 1000 Depends on: Min VTE Maximum Respiratory Rate Range: 10 bpm to 70 bpm in CPAP, P A/C, and V A/C modes and 17 bpm to 70 bpm in P SIMV and V SIMV modes (Max Rtot)

• Page 152: Environmental

  Specifications Environmental The following environmental conditions shall be observed: Table A-10.  Environmental Conditions for Storage or Transport Temperature Humidity Atmospheric pressure Altitude -40°C to +70°C 10% to 95% RH 500 hPa to 1060 hPa -152 m to 3964 m (-40°F to +158°F) (7.2 psi to 15.4 psi) (500 ft to 13 000 ft) Table A-11.  Environmental Conditions for Operation…

• Page 153: Pneumatic

  Pneumatic Pneumatic Table A-14.  Airway Resistances Inspiratory Exhalation 1.0 mbar at 30 lpm flow ±0.1 mbar 0.5 mbar at 30 lpm ±0.1 mbar 3.7 mbar at 60 lpm flow ±0.1 mbar 1.1 mbar at 60 lpm ±0.1 mbar Table A-15.  Patient Circuit Resistances Adult double limb Pediatric double limb 2 mbar at 30 lpm flow 2 mbar at 60 lpm flow…

• Page 154: Manufacturer’s Declaration

  Specifications Manufacturer’s Declaration A.10 Tables A-19 through A-22 contain the manufacturer’s declarations for the ventilator’s electromagnetic emissions and electromagnetic immunity, as well as a list of compliant cables. WARNING: Portable and mobile RF communications equipment can affect the performance of the Puritan Bennett™…

• Page 155
  Manufacturer’s Declaration Table A-19.  Electromagnetic Emissions The ventilator is intended for use in the electromagnetic environment specified below. The customer or the user of the ventilator should ensure that it is used in such an environment. Phenomenon and standard Compliance Electromagnetic environment – guidance Conducted and radiated RF emissions Group 1 The ventilator uses RF energy only for its internal functions.
• Page 156
  Specifications Table A-21.  Electromagnetic Immunity—Conducted and Radiated RF Phenomenon Basic EMC standard or test Immunity test levels for Home Healthcare method environment Conducted disturbances induced by RF IEC/EN 61000-4-6 fields 0,15 MHz–80 MHz 6 V in ISM and amateur radio bands between 0,15 MHz and 80 MHz 80% AM at 1 kHz Radiated RF EM fields…

• Page 157: Standards Compliance And Iec Classification

  Standards Compliance and IEC Classification Table A-22.  Compliant Cables and Accessories (Continued) Cable or accessory Maximum length 12V DC car adapter cable 5 m (16.4 ft) Oxygen inlet connector Puritan Bennett™ power pack (4098100) Standards Compliance and IEC Classification A.11 General Standards A.11.1 Medical Electrical Equipment: General Requirements for Safety IEC 60601-1 •…

• Page 158: Particular Standards

  Specifications Particular Standards A.11.3 Particular requirement for basic safety and Essential performance of home healthcare environmental • ventilators for ventilator-dependent patients — EN ISO 80601-2-72. Anesthetic and respiratory equipment — Conical connectors — Part 1: Cones and sockets EN ISO 5356-1. •…

• Page 159: Modes Of Ventilation

  B Modes of Ventilation Overview This chapter is a general description of the various modes of ventilation and breath types available with the Puritan Bennett™ 560 ventilator. Note: The default ventilation mode setting is P A/C; for more information, see below. Assist/Control (A/C) Modes When set to an Assist/Control mode, machine-initiated breaths are delivered at a clinician-set volume or pressure, inspiratory time, and rate.

• Page 160: Cpap Mode

  Modes of Ventilation CPAP Mode In CPAP, the ventilator maintains a constant level of pressure in the patient’s airway. PSV Mode PSV mode maintains a constant level of pressure in the patient’s airway during exhalation. In addi- tion, the ventilator applies a clinician-set pressure (Pressure Support) to each of the patient’s breaths.

• Page 161
  • If the ventilator fails any of the safety checks below, or if you cannot complete these checks, see section 3.9, Troubleshooting or call the equipment supplier or Covidien (see section 8.7, Service Assistance). WARNING: Provide the patient with an alternate means of ventilation before conducting these tests.

• Page 162: Operational Verification Checklist

  Operational Verification Checklist Table C-1.  Operational Verification Checklist Verify that the preventive maintenance schedule for the ventilator is followed. See Chapter 8, Routine Mainte- Pass nance. Ensure the patient breathing circuit is correctly attached to the ventilator, with all the necessary components, Pass and is free from any signs of damage and leaks.

• Page 163
  D Unpacking and Preparation The Puritan Bennett™ 560 ventilator is delivered with the items listed in Table D-1. Table D-1.  Items Included with Ventilator Item Quantity Printed user’s manual Clinician’s manual on CD Patient circuit and valve Set of six combination foam/fine particle air inlet filters Dual bag (carrying bag) Oxygen connector AC power cable…

• Page 164: Unpacking And Preparation

  Never use a ventilator or any components or accessories that appear to be damaged. If any signs of damage are evident, contact your equipment supplier or Covidien. Clean the ventilator with a mild soap solution, if necessary (see Chapter 7, Cleaning).

• Page 165
  If the ventilator fails any alarm test or if you cannot complete these tests, see the Troubleshooting section (refer to Chapter 3, Alarms and Troubleshooting) of this manual or call your equipment supplier or Covidien (refer to section 8.7, Service Assistance). WARNING: The Min PIP alarm setting must be adjusted for the patient, but must also be set high enough to allow the Patient Disconnection alarm to trigger properly.

• Page 166: Alarms Tests

  Alarms Tests Low Pressure Test WARNING: The Min PIP alarm setting must be adjusted for the patient, but must also be set high enough to allow the Patient Disconnection alarm to trigger properly. Perform the following test to ensure that the Low PIP alarm is properly set.

• Page 167: Max Leak Test (Only Niv

  Max Leak Test (Only NIV) Max Leak Test (Only NIV) WARNING: The Max Leak alarm setting must be adjusted for the patient, but must also be set low enough to allow the High Leakage alarm to trigger properly. Perform the following test to ensure that the alarm is functioning properly.

• Page 168: Circuit Check

  Alarms Tests Press and hold the VENTILATION ON/OFF key for 3 seconds, then release it. Press the VENTILATION ON/OFF key again to confirm stop. Ventilation stops • Circuit Check Perform a circuit check whenever replacing or altering a patient circuit. Ensure the patient is fully disconnected from the ventilator prior to starting this test.

• Page 169: Performing The Circuit Check

  Circuit Check Performing the Circuit Check E.3.2 To perform a circuit check: Verify that the proximal pressure tube of the patient circuit is properly connected to the proximal pres- sure port (see section 4.4, Patient Circuit). Verify that the exhalation valve tube is connected to the exhalation valve port. Block the patient connection port or patient wye of the patient circuit (see Figure E-4).

• Page 170: Figure E-6.   Circuit Check (Complete, Passed)

  Alarms Tests Increase pressure to 30 mbar (±10% with no leak) Show flow sensor measurement as Leak in Lpm (updated every 2 seconds) Sound a short beep every time the flow measurement is updated Sound a long audible beep once the check is complete Show PASS (see Figure E-6) or FAIL (see Figure E-7) in the Test Status field Figure E-6.  Circuit Check (complete, passed) Figure E-7.  Circuit Check (complete, failed)

• Page 171: Troubleshooting A Failed Check

  Power Failure Test Troubleshooting a Failed Check E.3.3 If the circuit check fails, do the following: Ensure an approved circuit is in use. See Table F-2.   Check patient circuit connections to the ventilator, examining each for leakage and tightness. Replace the patient circuit if necessary. Rerun the circuit check.

• Page 172: Occlusion Test

  Alarms Tests The AC Power Disconnection alarm is shown • Figure E-8.  Ventilator Screen (AC Power Disconnection alarm shown) Press the ALARM CONTROL key twice to reset the alarm. Reconnect the ventilator to its AC power supply. Occlusion Test To perform an occlusion test: Verify that the pressure tube of the patient circuit is properly connected to the appropriate fitting on both the ventilator and the proximal pressure port (see section 4.4, Patient…

• Page 173: Battery Test

  Battery Test After two breaths or after 5 seconds, whichever takes longer, ensure that the following events occur: The high priority indicator (flashing red LED) illuminates • An audible alarm sounds • The Occlusion alarm is shown; the Low VTI alarm may also activate •…

• Page 174: Involuntary Stop Test

  Alarms Tests Figure E-11.  Ventilator Screen (AC Power Disconnection alarm shown) Press the ALARM CONTROL key twice to reset the alarm. Ensure that the following events occur: The internal battery indicator to the upper-left of the display illuminates • The battery symbol is shown at the top of the screen (along with its reserve capacity) •…

• Page 175: Table F-1.   List Of Consumables And Accessories

  Table provides a list of accessories that are available for the Puritan Bennett™ 560 ventilator. To order parts or accessories, contact your equipment supplier or Covidien representative. For a list of items delivered with the ventilator, see Appendix D, Unpacking and Preparation.

• Page 176: Parts And Accessories

  Adult-pediatric HME (formerly Hygrolife II) Table provides a list of consumable parts available for the ventilator. WARNING: To ensure proper performance of the ventilator, use a patient circuit recommended by Covidien in this manual; see Chapter 4, Installation and Assembly and Appendix F, Parts and Accessories.

• Page 177
  G Glossary AC Power Alternating current. Alarm Pause The audible and visual alarms cease and the alarm paused symbol appears. The symbol will remain until the cause of the alarm is addressed. For example, when the ventilator is running on internal battery, the AC Disconnection alarm may be paused, and the alarm paused symbol will appear until the device is plugged into AC.

• Page 178: Glossary

  Glossary Back Up Rate Rate of control cycles in PSV or SIMV modes during apnea phase. Battery Level Display of the remaining battery capacity; located adjacent to the battery symbol. Bias Flow Turbine flow during exhalation phase through the patient circuit to avoid rebreathing. An abbreviation for “breaths per minute,”…

• Page 179
  Exhalation Tidal Volume (VTE) Volume exhaled by the patient at each exhalation phase. Exhaled Tidal Volume (VTE) Exhaled volume measured for all breath types through the exhalation block. Monitored value avail- able only with double-limb patient circuit. Exhaled volume is computed using a five-breath average. Fraction of Inspired Oxygen (FiO Amount of oxygen delivered to the patient.
• Page 180
  Glossary Intentional Vent Stop Alarm Ventilation has been switched off by the user/caregiver and the ventilator is in standby. I/T Ratio Inspiratory time versus total breath time ratio. Liters (a unit of volume). Leak When ventilating with a double-limb circuit in leak configuration, it is the average unexpected leak during each cycle and over the past 24-hour period.
• Page 181
  Minimum Inspiratory Time Minimum inspiratory time before allowing the patient to exhale. M Vol (Minute Volume) Flow delivered at each breath to the patient is measured by the inspiratory flow sensor and that measurement is used to calculate minute volume (Vt × Rtot). Non-Invasive Ventilation (NIV) Patient ventilation without the use of an endotracheal tube;…
• Page 182
  Glossary Pressure Support (P Support) Augmentation of the patient’s ventilation synchronously with inspiratory effort until a preset pres- sure is met. Pressure is maintained until inspiratory flow is reduced to a percentage of peak flow that depends on the exhalation sensitivity setting for the inspiration, when the ventilator cycles into exhalation.
• Page 183
  V A/C (Volume Assist/Control) A ventilator mode which provides machine-initiated breaths are delivered at a clinician-set volume inspiratory time, and rate. Vent Time (Ventilation Time) The ventilation duration data is based on the patient counter and shows the total ventilation time in hours and minutes over the previous 24-hour period.
• Page 184
  Glossary Page Left Intentionally Blank User Manual…
• Page 185
  Index INTENTIONAL VENT STOP ……3-13, 3-22 KEYPAD FAULT ……..3-13, 3-22 AC power LOW BATTERY .
• Page 186
  Index Reserve capacity display Check Settings alarm Ventilation running ……..6-4 Cause &…
• Page 187
  Index High Internal Temperature alarm Device Fault 7 alarm Cause & response ………3-12 Cause &…
• Page 188
  Index Maintenance ……….8-10 Periodic test .
• Page 189
  Index Power Supply Loss alarm Single-limb patient circuit Cause & response ……… 3-14 Installing Corrective action .
• Page 190
  Index USB menu VTI Not Reached alarm Transfer continuously ……..5-5 Cause &…
• Page 192
  Part No. PT00106571 Rev A 2019-07 © 2019 Covidien. All rights reserved. Covidien llc 15 Hampshire Street, Mansfield, MA 02048 USA Covidien Ireland Limited, IDA Business and Technology Park, Tullamore, Ireland. www.Medtronic.com [T] 1 800 635 5267…

• Page 1
  User’s Manual Puritan Bennett 560 Ventilator…
• Page 2
  To obtain information about a warranty, if any, contact Covidien Technical Services at 1.800.635.5267 or your local representative. Purchase of this instrument confers no express or implied license under any Covidien patent to use the instrument with any ventilator that is not manufactured or licensed by Covidien.

• Page 3: Table Of Contents

  Contents Purpose of This Manual ……….Qualification of Personnel .

• Page 4
  Contents Oxygen ……….. . 4–13 4.8.1 Administering Oxygen .
• Page 5
  Contents B Modes of Ventilation ……….B–1 Modes of Ventilation .
• Page 6
  This page intentionally blank. User’s Manual…
• Page 7
  ECTION Figures ……. Figure 1-1. Locations of Labels – Top-Front View 1–16 .
• Page 8
  Figures ……… . Figure 5-10.
• Page 9
  ECTION Tables ……….Table 1-1.
• Page 10
  This page is intentionally blank. viii User’s Manual…

• Page 11: Purpose Of This Manual

  Information regarding your product warranty is available from your sales representative or Covidien. Extended Service The Puritan Bennett™ 560 Ventilator offers extended service contracts/warranties for purchase when the ventilator is purchased. Please contact your local Covidien Sales or Service Representative for additional information. For online technical support, visit the SolvIT…

• Page 12: Technical Support

  Preface Technical Support Technical Service Contacts: Covidien Argentina Covidien Australia Covidien Austria GmbH Aguero 351 52A Huntingwood Drive Campus21 Capital Federal — 1171 ABC, Huntingwood, NSW 2148 Europaring F09402 Argentina Australia Brunn am Gebrige Tel: (5411) 4863-5300 Telephone (+61) 1800 350702 A-2345 Österreich…

• Page 13
  Tel +34 93 475 86 69 Fax + 46 858 56 05 29 Fax +27 115 429 547 Fax +34 93 373 87 10 Covidien Switzerland Covidien UK & Ireland Covidien Singapore Roosstr. 53 Unit 2, Talisman Business Park Singapore Regional Service…
• Page 14
  This page is intentionally blank. User’s Manual…

• Page 15: Safety Information

  1 Safety Information Definitions This manual uses three indicators to highlight critical information: Warning, Caution, and Note. They are defined as follows: Warning Indicates a condition that can endanger the patient or the ventilator operator. Warning Caution Indicates a condition that can damage the equipment. Note: Indicates points of particular emphasis, that make operation of the ventilator more efficient or convenient.

• Page 16
  If the ventilator fails the alarm tests or if you cannot complete the tests, refer to chapter “Troubleshooting” or call your equipment supplier or Covidien. • When an alarm condition is triggered, or there is evidence of a patient-ventilator fault or problem, examine the patient first before examining the ventilator.
• Page 17
  41 °C (106 °F). This may lead to undesirable side effects for the patient. To avoid injury to the patient move the patient and the ventilator to a cooler location. For more information, contact Covidien. •…
• Page 18
  Safety Information • The operator should connect the ventilator to an AC power source whenever available, for safer operation. • The maximum recommended shelf life of the internal battery is two (2) years. Do not use a battery that has been stored for two years prior to its first use. •…
• Page 19
  Safety Information • The exhalation block is intended for single use by a single patient . It may periodically be cleaned, but it cannot be disinfected or sterilised. To maintain good measurement quality when used continuously, clean the exhalation block periodically (refer to section 7.3, “Cleaning the Exhalation Block”).
• Page 20
  For more information, contact Covidien or your equipment supplier. • To connect the ventilator to a Nurse Call device, contact Covidien or your equipment supplier to check the ventilator’s compatibility with the Nurse Call device and order a suitable connection cable.
• Page 21
  • To ensure proper servicing and avoid the possibility of physical injury to personnel or damage to the ventilator, only personnel authorised and qualified by Covidien should attempt to service or make authorised modifications to the Puritan Bennett™ 560 Ventilator.
• Page 22
  Do not attempt to open, repair or otherwise service the ventilator yourself. Doing so might endanger the patient, damage the ventilator, and/or void your warranty. Only personnel authorised and qualified by Covidien should repair, open or service the ventilator. •…
• Page 23
  Safety Information • To connect the ventilator to an external power source, first ensure the ventilator’s I/O switch is off (O). Then, connect the desired power cable to the ventilator. Finally, connect the power cable to the external power source. •…
• Page 24
  The use of any accessory other than those specified, with the exception of the power supplies or cables sold by Covidien, may lead to an increase in electromagnetic emissions or a decrease in the equipment protection against electromagnetic emissions. If the ventilator is used adjacent to such accessories or stacked with such devices, the ventilator’s performance should be monitored…

• Page 25: Symbols And Markings

  Safety Information Symbols and Markings Table 1-1. Ventilator Symbols Symbols Descriptions It is essential to read, understand, and follow these instructions before using the Puritan Bennett™ 560 Ventilator (ISO 7000-0434A). This symbol appears on the ventilator’s back panel, see Table 1-2, item 5.

• Page 26
  Safety Information Table 1-1. Ventilator Symbols (Continued) Symbols Descriptions This symbol appears on the ventilator’s front panel ALARM CONTROL key; see Figure 2-3 on page 2-6, item 3. (See my notes, to the left and below, in red). This key is used to: cancel the audible portion of alarms for 60 seconds at a time; cancel an alarm. For more information, refer to section E, “Alarms Tests.”…
• Page 27
  Safety Information Table 1-1. Ventilator Symbols (Continued) Symbols Descriptions Flow shape (“flow distribution shape”, inspiratory phase) parameter. These symbols appear on the ventilation mode menu screens; selectable for V A/C mode only. For more information, refer to chapter 5, “Operating Procedures”.
• Page 28
  This symbol indicates a communications port for interfacing with a USB connector. Figure 2-2, item 11. PC connector. This symbol indicates a port that can be used by authorised Covidien product service personnel or Covidien service personnel for software maintenance. See Figure 2-2, item 10.

• Page 29: Labels / Identification And Instruction Information

  Safety Information Labels / Identification and Instruction Information Various labels or specific markings are affixed to the ventilator that describe precautions to be taken for the correct use of the ventilator and contribute to the traceability of the product. Refer to Table 1-2 and the figures on the following pages for illustrations of these labels and markings and their locations on the…

• Page 30: Figure 1-1. Locations Of Labels — Top-Front View

  Safety Information Table 1-2. Ventilator Labels and Markings (Continued) 13. FIO Label (Figure 1-1, Figure 1-4) Note: The item number callouts in the following figures refer to those listed in Table 1-2. Figure 1-1. Locations of Labels – Top-Front View 1-16 User’s Manual…

• Page 31: Figure 1-2. Locations Of Labels — Front-Left View

  Safety Information Figure 1-2. Locations of Labels – Front-Left View Figure 1-3. Location of Labels and Markings – Rear View User’s Manual 1-17…

• Page 32: Figure 1-4. Location Of Labels — Bottom View

  Safety Information Figure 1-4. Location of Labels – Bottom View 1-18 User’s Manual…

• Page 33: Ventilator Overview

  2 Ventilator Overview Indications for Use The Device name is indicated for the continuous or intermittent mechanical ventilatory support of patients weighing at least 11 lb (5 kg) who require mechanical ventilation. The ventilator is a restricted medical device intended for use by qualified, trained personnel under the direction of a doctor. It is essential to read, under- stand, and follow these instructions before using the Puritan Bennett™…

• Page 34: Contraindications

  Ventilator Overview Target Operators The ventilator may be operated by: • Respiratory therapists • Doctors • Nurses • Homecare providers • Patient and patient’s families Warning This ventilator must be used only under the responsibility and on the prescription of a doctor. Contraindications This ventilator is not for use with anesthetic gases, and is not intended for use as an emergency transport ven- tilator.

• Page 35: Device Classification

  Ventilator Overview Warning Users must always possess an additional breathing circuit and exhalation valve while using the Device name. Device Classification The ventilator’s IEC / EN 60601-1classification is as follows: • Protection/Insulation class (electric shock): Class II • Protection index of enclosure: IP31 •…

• Page 36: Front Panel

  Ventilator Overview Front Panel LCD Display – Displays information about the ventilator Exhalation Valve Port – Nipple for providing piloting including patient hours and software version, ventilation pressure to the exhalation valve. Controls the open-closed modes and settings, and monitored and calculated patient position of the exhalation valve.

• Page 37: Back Panel

  Ventilator Overview Back Panel Ergonomic carrying handle. PC Cable Connector: USB mini-B connector used for Puritan Bennett™ Ventilator Test Software. On/Off (I/O) switch with protective cover: Inlet Port: Device powered on in position I; device Connects the ventilator to a low pressure oxygen switched off in position 0.

• Page 38: Control Panel

  Ventilator Overview Control Panel Alarm indicators (two LEDs): DOWN/FREEZE key: • Red indicator: Moves the cursor down and decreases parameter values. • • During ventilation, freezes displayed waveform in the Continuous: Very High Priority (VHP) alarm Waveform menu. activated • High priority (HP) alarm activated.

• Page 39: Ventilation Menu

  Ventilator Overview Ventilation Menu Ventilation menu with ventilation on standby. Ventilation menu during ventilation. General information line: Ventilation settings: Preferences menu access Displays the current ventilation mode, line: Displays the specific ventilation along with the following: parameter values for the Highlight this line and press •…

• Page 40: Alarm Menu

  Ventilator Overview Alarm Menu Alarm menu with ventilation on standby. Alarm menu when not in standby. Title line: Alarm settings: Access line to Alarm Logs menu. Displays ventilation mode and the Displays the specific alarm parameter following symbols: values for the currently selected Highlight this line and ENTER ventilation mode, which are:…

• Page 41: Waveforms Menu

  Ventilator Overview 2.10 Waveforms Menu The display of waveforms (Figure 2-6) is optional and can be selected using the Menu key The Wave- form menu is only accessible when ventilation is active. Title line: Graphic zone: Numeric zone: • Displays ventilation mode and the Displays the patient’s pressure and Displays monitored data.

• Page 42: Usb Memory Device Menu

  Keep in mind that troubleshooting information is available in this manual to assist you in the event of a prob- lem. Refer to chapter 3, “Alarms and Troubleshooting”. If you cannot determine the cause of a problem, contact your equipment supplier or Covidien. Refer to chap- 8.3, “Service Assistance” 2-10 User’s Manual…

• Page 43: Alarms And Troubleshooting

  3 Alarms and Troubleshooting Warning Setting Alarm limits to extreme values can cause the ventilator alarms to malfunction. When an alarm condition is triggered, or there is evidence of a patient-ventilator fault or problem, examine the patient first before examining the ventilator. Note: Many of the functions of the ventilator are not accessible when the Locking key is enabled.

• Page 44: Alarm Level Of Priority

  Alarms and Troubleshooting Alarm Level of Priority The alarm hierarchy for signalling the level of alarm criticality is listed below. • Very High Priority (VHP): Immediate critical situation; ventilation is impossible: Continuous Sound Signaling / With or Without Continuous Red LED Illumination / With or Without Message / With or Without Display Lighting (it is possible for an alarm condition to occur that may not have both a message and lighting).

• Page 45: Alarm Display

  Alarms and Troubleshooting Alarm Display During operation, when an alarm is activated: • One of the red or yellow alarm indicators to the left of the ALARM CONTROL illuminates and flashes. • An alarm tone sounds. • A message is displayed and flashes in reverse video at the bottom of the Ventilation Menu or Alarm Menu.

• Page 46: Alarm Logs Menu

  Alarms and Troubleshooting Alarm Logs Menu All alarms are recorded in the internal memory of the ventilator at the time they are activated. The Alarm Logs menu is used to display the last eight (8) alarms activated, along with their date and time of activation.

• Page 47: Silencing The Audible Portion Of Alarms

  Alarms and Troubleshooting To dismiss the Alarm Logs screen manually: Press the ENTER key when the cursor is on the “Back” line. The Alarm Logs screen is dismissed automatically: • After 15 seconds if no keyboard action is detected • When a High Priority alarm is triggered Note: Only qualified service personnel may access all alarms and events recorded by the ventilator.

• Page 48: Figure 3-5. Manually Pausing Alarms

  Alarms and Troubleshooting Warning Alarm volume should be adjusted with respect to the ventilator’s operating environment and so that the patient’s caretakers can hear the alarms. The audible alarm vents located at the front of the device should never be obstructed. The alarm can be paused with the Alarm Pause function by pressing the ALARM CONTROL key twice once the alarm has been declared.

• Page 49: Re-Activating Alarms

  Alarms and Troubleshooting Re-activating Alarms Alarms that have been paused and whose activation conditions continue to exist can be reactivated. To reactivate alarms, proceed as follows: 1. Press the MENU key to access the Alarm Setting menu, if this is not the menu currently displayed.

• Page 50: Overview Of Alarms

  Alarms and Troubleshooting Overview of Alarms Note: The message: “*IF PERSISTS RESTART/SRVC” will occur only if the alarm condition continues for longer than 30 seconds. Note: Many of the functions of the ventilator are not accessible when the Locking key is enabled.

• Page 51
  Alarms and Troubleshooting Table 3-1. Overview of Alarms (Continued) Audio Alarm Paused Paused Alarm Message Cause/Ventilator Response Priority Avail. Avail. Buzzer Battery Failure. The Battery BUZZER FAULT4 Buzzer Voltage is too low. RESTART/SRVC Internal technical problem that prevents the battery sounding the POWER SUPPLY LOSS alarm.
• Page 52
  Alarms and Troubleshooting Table 3-1. Overview of Alarms (Continued) Audio Alarm Paused Paused Alarm Message Cause/Ventilator Response Priority Avail. Avail. Alarm activation occurs: CHECK Systematically after software • SETTINGS versions have changed. Loss of memorised parameters • Consequence: Locking Key disabled •…
• Page 53
  Alarms and Troubleshooting Table 3-1. Overview of Alarms (Continued) Audio Alarm Paused Paused Alarm Message Cause/Ventilator Response Priority Avail. Avail. Internal battery capacity < 10 min. EMPTY BATTERY or 3%. (battery voltage < 22.5V) Consequence: ventilation comes to a halt. Abnormally high expired flow during EXH VALVE the inspiratory phase of three…
• Page 54
  Alarms and Troubleshooting Table 3-1. Overview of Alarms (Continued) Audio Alarm Paused Paused Alarm Message Cause/Ventilator Response Priority Avail. Avail. Rate measured greater than HIGH RATE Max Rtot set during three consecutive breaths. Alarm activation occurs: After three consecutive breaths. •…
• Page 55
  Alarms and Troubleshooting Table 3-1. Overview of Alarms (Continued) Audio Alarm Paused Paused Alarm Message Cause/Ventilator Response Priority Avail. Avail. Occurs in VALVE configuration when OCCLUSION the tidal volume is measured below CHECK CIRCUIT* 20ml during three consecutive breaths for PSV, CPAP, PA/C and P SIMV modes.
• Page 56
  Alarms and Troubleshooting Table 3-1. Overview of Alarms (Continued) Audio Alarm Paused Paused Alarm Message Cause/Ventilator Response Priority Avail. Avail. Faulty internal pressure sensor PRES SENS FLT1 signal. RESTART/SRVC Alarm activation occurs: After 15 seconds. • Faulty proximal pressure sensor PROX SENS FLT2 signal.

• Page 57: Troubleshooting

  To ensure proper servicing and avoid the possibility of physical injury to personnel or damage to the ventilator, only personnel authorised and qualified by Covidien should attempt to service or make authorised modifications to the Puritan Bennett™ 560 Ventilator.

• Page 58
  Alarms and Troubleshooting Table 3-2. Alarms and Corrective Actions (Continued) Alarm Message or Symptom Possible Reason(s) For The Alarm Event Corrective Action(s) Restart ventilator to see if alarm clears. If Battery problem that prevents it from BATTERY FAULT1 not, replace the ventilator and call your operating.
• Page 59
  Alarms and Troubleshooting Table 3-2. Alarms and Corrective Actions (Continued) Alarm Message or Symptom Possible Reason(s) For The Alarm Event Corrective Action(s) Obstruction or abnormal damage of the Clean or replace the exhalation valve and/or exhalation valve. its control tube. Remove moisture from exhalation block and valve.
• Page 60
  Alarms and Troubleshooting Table 3-2. Alarms and Corrective Actions (Continued) Alarm Message or Symptom Possible Reason(s) For The Alarm Event Corrective Action(s) Operating speed of the cooling fan not Restart ventilator to see if alarm clears. If COOLING FAN properly adjusted for the internal ambient not, replace the ventilator and call your RESTART/SRVC temperature of the device.
• Page 61
  Alarms and Troubleshooting Table 3-2. Alarms and Corrective Actions (Continued) Alarm Message or Symptom Possible Reason(s) For The Alarm Event Corrective Action(s) Note: Always consult the clinician before changing PEEP, FIO , pressure, volume or Rate settings. Check and properly connect the patient circuit connections.
• Page 62
  Alarms and Troubleshooting Table 3-2. Alarms and Corrective Actions (Continued) Alarm Message or Symptom Possible Reason(s) For The Alarm Event Corrective Action(s) Note: Ensure that you are operating the ventilator within the proper temperature range (refer to Appendix A, “Specifications”). Put the device in a warmer environment (if the ambient temperature is too low) or in a cooler environment (if the ambient…
• Page 63
  Alarms and Troubleshooting Table 3-2. Alarms and Corrective Actions (Continued) Alarm Message or Symptom Possible Reason(s) For The Alarm Event Corrective Action(s) Note: Always consult the clinician before Adjustment of Max PIP too low (only for changing PEEP, FIO , pressure, volume or V A/C and V SIMV modes).
• Page 64
  Alarms and Troubleshooting Table 3-2. Alarms and Corrective Actions (Continued) Alarm Message or Symptom Possible Reason(s) For The Alarm Event Corrective Action(s) Note: Adjustment of the Max VTI level too low Always consult the clinician before (for PSV, CPAP, P A/C, P SIMV and V SIMV changing PEEP, FIO , pressure, volume or modes).
• Page 65
  Alarms and Troubleshooting Table 3-2. Alarms and Corrective Actions (Continued) Alarm Message or Symptom Possible Reason(s) For The Alarm Event Corrective Action(s) Clean, unblock, and/or properly connect the Patient circuit obstructed. patient circuit. Check and properly connect the patient circuit connections. Leak in the patient circuit.
• Page 66
  Alarms and Troubleshooting Table 3-2. Alarms and Corrective Actions (Continued) Alarm Message or Symptom Possible Reason(s) For The Alarm Event Corrective Action(s) OCCLUSION CHECK CIRCUIT Clean, unblock, and/or properly connect the Patient circuit obstructed. patient circuit. *IF PERSISTS RESTART/SRVC A non-vented configuration is being used or Replace the non-vented circuit with a the built-in leak in the mask or in the circuit vented one.

• Page 67: Additional Troubleshooting

  Alarms and Troubleshooting Table 3-2. Alarms and Corrective Actions (Continued) Alarm Message or Symptom Possible Reason(s) For The Alarm Event Corrective Action(s) Restart ventilator to see if alarm clears. If Defective inspiratory flow sensor or internal VTI NOT REACHED not, replace the defective device(s) and leak of the machine.

• Page 68
  Table 3-3. Additional Troubleshooting and Corrective Actions (Continued) Conditions Possible Causes Corrective Actions Replace the ventilator and call your Turbine noise. Light noise customer service representative. Filter and/or turbine silencer Replace the ventilator and call your deteriorated. customer service representative. Whistling noise or Replace the ventilator and call your Valve membranes damaged.

• Page 69: Installation And Assembly

  41 °C (106 °F). This may lead to undesirable side effects for the patient. To avoid injury to the patient move the patient and the ventilator to a cooler location. For more information, contact Covidien.

• Page 70: Connecting To External Ac Power

  The use of any accessory other than those specified, with the exception of the power supplies or cables sold by Covidien, may lead to an increase in electromagnetic emissions or a decrease in the equipment protection against electromagnetic emissions. If the ventilator is used adjacent to such accessories or stacked with such devices, the ventilator’s performance should be…

• Page 71: Figure 4-1. The Power Cable Holder

  Installation and Assembly that is inserted into the notch (Figure 4-1, item 2) of the battery cover: AC Power Cable Holder Figure 4-1. The Power Cable Holder To secure the AC power cable: 1. Insert the power cable holder (Figure 4-2, item 1) into the notch of the battery cover.

• Page 72: Connecting To An External Dc Power Source

  Installation and Assembly • The AC POWER indicator on the top left corner of the ventilator illuminates. • The indicator flashes while the battery charges and then turns off when the battery is fully charged. Refer to Figure 4-4 on page 4-4. If the AC power cable becomes disconnected or the AC power source fails, an “AC POWER DISCONNEC- TION“…

• Page 73: Figure 4-5. Connecting The Ventilator To An External Dc Power Source

  Installation and Assembly Note: An alternative means of ventilation should always be available, particularly when the patient is in transit or away from wall power. While using the ventilator on external battery power it is vital that a qualified caregiver (capable of providing necessary corrective actions in the event of alarm conditions) is present.

• Page 74: Patient Circuit

  Installation and Assembly To connect the DC power cable to the ventilator: 1. Line up the red marker dot on the ventilator’s DC power connector with the marker on the DC power cable (Figure 4-6, item 1). Align the red markers (dots and/or lines) before connecting…

• Page 75: Choosing The Patient Circuit Type

  To ensure proper performance of the ventilator, use a patient circuit recommended by Covidien in this manual; refer to chapter 4, “Installation and Assembly”…

• Page 76: Figure 4-7. Single Limb Patient Circuit With Exhalation Valve

  Installation and Assembly See also NOTE: Although shown here, the Figure 4-9 humidifier (item 3), water trap page 4-9. (item 4), and tubes upstream of the single limb patient circuit are not included with the ventilator. Contact your supplier for more information.

• Page 77: Figure 4-8. Double Limb Patient Circuit

  Installation and Assembly See also Figure 4-9 on page 4-9. Figure 4-8. Double Limb Patient Circuit Note: Although shown here, the humidifier (item 2), water traps (item 3), and their connecting tubes are not included with the patient circuit or ventilator. Contact your supplier for more information. Inhalation Port Exhalation Valve Tube…

• Page 78: Figure 4-10. Single Limb Patient Circuit Without Exhalation Valve

  Installation and Assembly 5. Place a water trap (item 3) between the outlet port of the humidifier and the patient end. 6. Place a vented (NIV) interface to the end of the patient circuit. (item 5) Figure 4-10. Single limb Patient Circuit Without Exhalation Valve For both types of circuits, shown previously, you should connect the end of the proximal pressure tube as close as possible to the patient (at the mask or cannula entry, if possible) so that the ventilator can account for all load losses due to the circuit and its potential accessories.

• Page 79: Filters

  Installation and Assembly Filters Warning Regularly check the cleanliness of the air inlet filter located on the rear of the ventilator. If necessary, replace the filter before the recommended replacement period is over (see chapter “Routine Maintenance”). This is particularly important when the ventilator is installed on a wheelchair, because environmental conditions may cause the filter to become dirty more rapidly.

• Page 80: Humidifier

  Installation and Assembly • Connected to the FROM PATIENT port: This filter protects the internal exhalation flow sensor from the gases exhaled by the patient. Refer to Figure 4-8, item 10. Figure 4-12. Bacteria Filter Refer to the manufacturer’s instructions for more information about the use and maintenance of the bacteria filter(s).

• Page 81: Exhalation Block

  Installation and Assembly water trap. If you notice any moisture in the patient circuit, you need to replace the wet circuit components with dry ones. Refer to the humidification device’s instruction for information on operating, cleaning, and sterilising the humidifier. Exhalation Block Warning The exhalation block is intended for single use by a single patient…

• Page 82: Connecting The Oxygen Supply

  Installation and Assembly The Puritan Bennett™ 560 Ventilator can be used with an optional oxygen analyser with minimum and maximum concentration alarms. Always measure the delivered oxygen with a calibrated oxygen analyser (FIO kit) that features a minimum and maximum concentration alarm in order to ensure that the prescribed oxygen concentration is delivered to the patient.

• Page 83: Figure 4-16. Connecting The Oxygen Supply System

  Installation and Assembly To connect the oxygen supply system to the ventilator: Refer to Figure 4-16 as required: 1. Inspect the oxygen supply’s connector (Figure 4-16, item 1) to ensure that connector’s black O-ring (item 2) is not missing. 2. Push the oxygen supply’s oxygen connector (item 1) into the ventilator’s oxygen connector (Figure 4-16, item 3).

• Page 84
  Installation and Assembly Warning The coupler must not remain connected to the oxygen connector unless it also connected to a leak-proof, external oxygen gas source. When an oxygen supply is not being used with the ventilator, disconnect the oxygen source completely from the ventilator. In the event of an oxygen leak, shut down the supply of oxygen at its source.

• Page 85: Fitting The Ventilator Into The Dual Bag

  Installation and Assembly Fitting the Ventilator into the Dual Bag The Dual Bag is a carrying bag with a dual function. It allows the Puritan Bennett™ 560 Ventilator to either be mounted onto a wheelchair or carried as a backpack. (see Figure 4-19) Warning…

• Page 86: Figure 4-19. Using The Dual Bag Accessory

  Installation and Assembly Figure 4-19. Using the Dual Bag Accessory To install the Dual Bag onto a wheelchair do the following: 1. Unclip the two backpack straps from the side clips. 2. Clip the suspension belt onto the central ring. 3.

• Page 87: Mounting The Ventilator On The Utility Cart

  Installation and Assembly 4.11 Mounting the Ventilator on the Utility Cart Match the mounting holes (item 1) on the bottom of the Puritan Bennett™ 560 Ventilator to the mounting studs (item 2) on the top of the utility cart platform. User’s Manual 4-19…

• Page 88: Connecting The Nurse Call Cable

  Before using the Nurse Call system, ensure that its connections are secure and it operates properly. For more information, contact Covidien. To connect the ventilator to a Nurse Call device, contact Covidien to check the ventilator’s compatibility with the Nurse Call device and order a suitable connection cable.

• Page 89: Operating Procedures

  If the ventilator fails the alarm tests or if you cannot complete the tests, refer to section 3.8, “Troubleshooting” or call your equipment supplier or Covidien. Due to its limited internal battery’s reserve capacity, the ventilator should only be operated on the internal battery when no other power source is available. Ensure that the internal battery…

• Page 90: Figure 5-1. Turning On The Ventilator

  Operating Procedures To turn the ventilator on: • Set the I/O switch (a covered, rocker-type switch located at the rear of the ventilator) to the I position, as shown in Figure 5-1 below. Figure 5-1. Turning on the Ventilator The following events occur: •…

• Page 91: Usb Menu Parameters

  The USB Menu is not accessible from the Setup Menu or Maintenance menu. To access patient data via a PC, a dedicated software package, Puritan Bennett™ Respiratory Insight Software, is available for Clinicians. Contact Covidien or your Puritan Bennett™ product representative for further infor- mation.

• Page 92: Usb Menu

  Operating Procedures 5.2.2 USB Menu To access the USB menu when a USB memory device is connected: Press the MENU key several times, until the USB Menu appears: Figure 5-4. Selecting the USB Menu In case of high priority alarm activation the ventilator will automatically display the alarm page. To return to the USB Menu, press the MENU key.

• Page 93: Transfer Trends

  Operating Procedures • The cursor changes to the plus/minus symbol. • The parameter selected to be modified flashes. 3. Press UP or DOWN to change the selected parameter’s value. 4. Press ENTER to confirm the new parameter setting. • The new parameter setting is displayed continuously. •…

• Page 94
  Operating Procedures • The parameter selected to be modified flashes. 3. Press UP or DOWN to change the selected parameter’s value. 4. Press ENTER to confirm the new parameter setting. • The new parameter setting is displayed continuously. • The cursor is placed at the STOP position. 5.

• Page 95: Starting Ventilation

  Operating Procedures Starting Ventilation Before starting ventilation, refer to Appendix C, “Operational Verification Checklist”, and set the parameter values in the Preferences menu.) Warning Verify the functionality of the alarm conditions before connecting the patient to the ventilator. Before starting ventilation, ensure that the device is properly assembled and that the air inlet, cooling vents, and alarm sound diffusion holes are not obstructed.

• Page 96: Stopping Ventilation

  Operating Procedures Front Panel Keyboard Figure 5-8. Starting Ventilation Stopping Ventilation Warning Do not allow a patient to remain connected to the ventilator when ventilation is stopped, because a substantial quantity of expiratory gas, primarily carbon dioxide, may be inhaled by the patient.

• Page 97: Turning Off The Ventilator

  Operating Procedures • A new message appears that directs the user to press the key again to confirm ventilation stop. (shown in the graphic below). Figure 5-10. Stopping Ventilation (2) • A double “beep“ sounds. 3. Release the VENTILATION ON/OFF key.

• Page 98
  This page is intentionally blank. 5-10 User’s Manual…

• Page 99: Internal Battery

  6 Internal Battery Warning Even though the Puritan Bennett™ 560 Ventilator meets current safety standards, the internal Lithium-ion battery of the device exceeds the 100Wh threshold and is therefore considered to be Dangerous Goods (DG) Class 9 – Miscellaneous, when transported in commerce. As such, the Puritan Bennett™…

• Page 100: Battery Operation

  Internal Battery Table 6-1. Internal Battery Reserve Capacity Displayed Values Average Operating Time on Internal Battery Power Vt 200 ml (± 5 ml) PIP  10 mbar (± 2 mbar) 11 hours (–10%) Rtot  20 bpm Vt300ml (± 5 ml) PIP …

• Page 101
  Internal Battery Figure 6-1. Internal Battery Indicator • A loss of external supply alarm is activated. If ventilation is stopped, the internal battery reserve capacity is displayed as a percentage of battery charge. Refer to Figure 6-2. Figure 6-2. Battery Reserve Capacity as a Percentage If the ventilator is running, the internal battery reserve is momentarily displayed as a percentage.

• Page 102: Testing The Battery

  Internal Battery Warning Due to its limited internal battery’s reserve capacity, the ventilator should only be operated on the internal battery when no other power source is available. Ensure that the internal battery never becomes fully discharged. When the “LOW BATTERY“ alarm is triggered, immediately connect the ventilator to an AC power supply to maintain ventilation and recharge the internal battery.

• Page 103: Storage

  Internal Battery • The “INTERNAL BATTERY“ indicator flashes (Figure 6-4, item 2). Figure 6-4. Power Indicators When Charging the Battery When the battery charge is complete, the “INTERNAL BATTERY“ indicator turns off. Warning Even if the “INTERNAL BATTERY“ indicator is off, charge of the battery may sometimes be incomplete regardless of charge time when the ambient temperature is above 40 °C (104 °F).

• Page 104
  Note: When the device is in storage it should be recharged monthly to maximise battery life. If the battery is stored for more than one month at a temperature greater than 21 °C (70 °F), or for more than one or two weeks at a temperature greater than 45 °C (113 °F), the reserve capacity of the battery may be affected.

• Page 105: Cleaning

  7 Cleaning Warning A patient treated by mechanical ventilation is highly vulnerable to the risks of infection. Dirty or contaminated equipment is a potential source of infection. Clean the ventilator and its accessories regularly and systematically before and after each use and following any maintenance procedure to reduce the risks of infection.

• Page 106: Cleaning The Accessories

  Cleaning Table 7-1. Approved Cleaning Solutions for Exterior Ventilator Surfaces Description Mild dishwashing detergent 70% isopropyl alcohol (rubbing alcohol) 10% chlorine bleach (90% tap water) Glutaraldehyde Hospital disinfectant cleaners Hydrogen peroxide 15% ammonia (85% tap water) Ammonia-based household cleaners Household cleaners Cleaning the Accessories Follow the accessory manufacturer’s instructions for cleaning the ventilator’s accessories and components, including the patient circuit.

• Page 107: Routine Maintenance

  Do not attempt to open, repair or otherwise service the ventilator yourself. Doing so might endanger the patient, damage the ventilator, and/or void your warranty. Only personnel authorised and qualified by Covidien should repair, open or service the ventilator. Replacing the Air Inlet Filter Warning Regularly check the cleanliness of the air inlet filter located on the rear of the ventilator.

• Page 108: Recommended Schedule Of Maintenance

  Routine Maintenance b. The filter is properly installed in its housing. Proper installation of the filter prevents particles from entering the device. Figure 8-1. Replacing the Air Inlet filter Recommended Schedule of Maintenance Consumables and Replacement Intervals When used under normal circumstances — a relatively dust-free atmosphere, and without damage to the device and its components (shocks, cracks, significant dirt) — the intervals for replacing the ventilator’s consum- able elements are as follows: Table 8-1.

• Page 109
  Routine Maintenance Note: For all additional accessories not necessarily considered as consumables consult the manufacturer’s recommendations. To prevent any risk of cross contamination we recommend the use of DAR™ filters (Ref: 351/5856 or equivalent) to protect the patient outlet port and the exhalation block port. Warning Regularly check the cleanliness of the air inlet filter located on the rear of the ventilator.

• Page 110: Service Assistance

  In the event of a problem with the ventilator, refer to chapter 3, “Alarms and Troubleshooting”. If you cannot determine the cause of the problem, contact your equipment supplier or Covidien. For more information and local Covidien Technical Service Contact details, See “Technical Support”…

• Page 111: A Specifications

  A Specifications Physical Table A-1. Physical Description (Excluding Accessories) Ventilator Weight 9.9 lb. (4.5 kg) Ventilator Dimensions 9.25 in wide x 12.40 in deep x 6.0 in high (235 mm wide x 315 mm deep x 154 mm high) Connectors Inspiratory limb connector: ISO 22 mm (OD) conical Exhalation limb connector (on exhalation block): ISO 22 mm (ID) conical…

• Page 112: Table A-3. Internal Lithium Ion Battery

  Specifications Table A-3. Internal Lithium Ion Battery Voltage 25.2 VDC Full-load capacity 4.8 Ah Ampere-hour rating On standby: 1.5 Ah During ventilation: 0.5 Ah Watt hour rating 124Wh to 126Wh Charging current Standby mode 1.5 A/hr. (duration: < 6 hr.) •…

• Page 113: Indicators And Alarms

  Specifications Indicators and Alarms Table A-5. Power Indicators Ventilation ON/OFF AC power DC power Internal Battery Blue in standby mode Green Green Flashing if the battery • • charge is in progress. Not lit if ventilation is in • progress. Continuously lit if the •…

• Page 114: Range, Resolution, And Accuracy

  Specifications Table A-9. Monitored Parameter Tolerances (Continued) Ventilator Parameters Tolerances Exhalation Tidal Volume (VTE) ± (10 ml + 10%VTE)*VTE Total Breath Rate (Rtot) ± 1 bpm I:E Ratio (I:E) ± 50 ms or 10%, whichever is greater I/T Ratio (I/T) ±…

• Page 115
  Specifications Table A-10. Ventilator Range, Resolution, and Accuracy (Continued) Ventilator Settings Range, Resolution, and Accuracy Pressure support Range: OFF or 5 mbar to 55 mbar in valve configuration (P Support) Range: 6 mbar to 30 mbar in leak in valve configuration Resolution: 1 mbar Accuracy: ±…
• Page 116
  Specifications Table A-10. Ventilator Range, Resolution, and Accuracy (Continued) Ventilator Settings Range, Resolution, and Accuracy PEEP Range: OFF (0.5 mbar) to 20 mbar Resolution: 1 mbar Accuracy: ± (1 mbar + 10%) mbar Default value: OFF Depends on: PIP in P A/C and PSV modes when Relative Pressure is set to YES Depends on: P Support and P Control in P SIMV mode when Relative Pressure is set to YES…

• Page 117: Environmental

  Specifications Table A-10. Ventilator Range, Resolution, and Accuracy (Continued) Ventilator Settings Range, Resolution, and Accuracy Minimum Peak Inspiratory Pressure Range: PIP- 20% (not adjustable in pressure breath) (Min PIP) Range: 2-52 in volume breath Resolution: N/A Maximum Peak Inspiratory Pressure Range: PIP+ 20 % (not adjustable in pressure breath) (Max PIP) Range: 12-60 in volume breath…

• Page 118: Usb

  Specifications Table A-13. USB Memory Device Specifications Characteristics Supported formats USB compatibility USB flash memory USB 2.0 or USB 1.1 Memory file format USB 32 bit format (sector size: 512 — 2,048 bytes) Number of files Maximum 999 USB size 128 MB to 4 GB Table A-14.

• Page 119: Manufacturer’s Declaration

  Specifications A.10 Manufacturer’s Declaration The following tables, Table A-20 through Table A-23, contain the manufacturer’s declarations for the ventila- tor’s electromagnetic emissions, electromagnetic immunity, and recommended separation distances between the ventilator and portable and mobile RF communications equipment, as well as a list of compliant cables. Warning Portable and mobile RF communications equipment can affect the performance of the Puritan Bennett™…

• Page 120: Table A-21. Electromagnetic Immunity

  Specifications Table A-21. Electromagnetic Immunity The ventilator is intended for use in the electromagnetic environment specified below. The customer or the user of the ventilator should ensure that it is used in such an environment. Electromagnetic Immunity Test IEC / EN 60601 Test Level Compliance Level Environment–Guidance Electrostatic discharge…

• Page 121: Table A-22. Electromagnetic Immunity — Conducted And Radiated Rf

  Specifications Table A-22. Electromagnetic Immunity – Conducted and Radiated RF The ventilator is intended for use in the electromagnetic environment specified below. The customer or the user of the ventilator should assure that it is used in such an environment. IEC / EN 60601-1-2 Test Electromagnetic Environment–…

• Page 122: Table A-23. Recommended Separation Distances

  Specifications Table A-22. Electromagnetic Immunity – Conducted and Radiated RF (Continued) Note: • At 80 MHz and 800 MHz, the higher frequency range applies. • These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects, and people.

• Page 123: Standards Compliance And Iec Classification

  Specifications Table A-24. Compliant Cables and Accessories Cable or Accessory Maximum length UK AC power cable assembly 1.8 m (5.9 ft) Japan AC power cable assembly 1.8 m (5.9 ft) China AC power cable assembly 1.8 m (5.9 ft) South Africa AC power cable assembly 1.8 m (5.9 ft) India AC power cable assembly 1.8 m (5.9 ft)

• Page 124
  Specifications Particular Standards Lung Ventilators for Medical Use- Particular Requirements for Basic Safety and Essential • Performance Part 2: Home Care Ventilators for Ventilator-Dependent Patient EN ISO10651- 2:2009. Lung ventilators for medical use – Particular requirements for basic safety and essential •…

• Page 125: B Modes Of Ventilation

  B Modes of Ventilation Modes of Ventilation This chapter is a general description of the various modes of ventilation and breath types available with the Device name. Note: The default ventilation mode setting is P A/C; for more information, see below. B.1.1 Assist/Control (A/C) Modes When set to an Assist/Control mode, machine-initiated breaths are delivered at a clinician-set volume or pres- sure, inspiratory time, and rate.

• Page 126: Psv Mode

  Modes of Ventilation B.1.4 PSV Mode PSV mode maintains a constant level of pressure in the patient’s airway during exhalation. In addition, the venti- lator applies a clinician-set pressure (Pressure Support) to each of the patient’s breaths. This has the same benefits as CPAP, with the additional benefit of assisting the patient in moving gas into his or her lungs.

• Page 127: C Operational Verification Checklist

  • Following maintenance or changes in ventilator settings If the ventilator fails any of the safety checks below, or if you cannot complete these checks, refer to section 3.8, “Troubleshooting” or call the equipment supplier or Covidien (refer to section 8.3, “Service Assistance”).

• Page 128
  This page is intentionally blank. User’s Manual…

• Page 129: D Unpacking And Preparation

  Never use a ventilator or any components or accessories that appear to be damaged. If any signs of damage are evident, contact your equipment supplier or Covidien. 4. Clean the ventilator with a mild soap solution, if necessary (refer to chapter “Cleaning”).

• Page 130
  Unpacking and Preparation Figure D-1. Puritan Bennett™ 560 Ventilator Figure D-2. Dual Bag User’s Manual…

• Page 131: E Alarms Tests

  Troubleshooting section (refer to chapter 3, “Alarms and Troubleshooting”) of this manual or call your equipment supplier or Covidien (refer to section 8.3, “Service Assistance” The setting of the Min PIP alarm must be adjusted for the patient, but must also be set high enough to allow the PATIENT DISCONNECTION alarm to trigger properly.

• Page 132: Power Failure Test

  Alarms Tests Power Failure Test Note: If the ventilator is operating on either the external power supply or the internal battery, you must plug it in to an AC power source before beginning this test. 1. Disconnect the ventilator from its AC power supply. Ensure that the following events occur: •…

• Page 133: Testing The Battery

  Alarms Tests 7. Press and hold the VENTILATION ON/OFF key for three (3) seconds, then release it. Press the VENTILATION ON/OFF key again to confirm stop. • Ventilation stops. Testing the Battery The ventilator is capable of testing the power of the battery (refer to chapter 6, “Internal Battery”).

• Page 134
  This page is intentionally blank. User’s Manual…

• Page 135: F Parts And Accessories

  Table F-1 provides a list of accessories that are available for the Device name. To order parts or accessories, contact your equipment supplier or Covidien representative. Note: The ventilator is delivered with the following items: a printed User’s Manual, a CD with Clinician’s Manual (printed copy available upon request);…

• Page 136: Table F-2. List Of Circuits

  Table F-2 provides a list of consumable parts available for the ventilator. Warning To ensure proper performance of the ventilator, use a patient circuit recommended by Covidien in this manual; refer to chapter 4, “Installation and Assembly” Appendix F, “Parts and Accessories”.

• Page 137: G Glossary

  G Glossary AC Power Alternating current. Alarm Pause The audible and visual alarms cease and the symbol appears. The symbol will remain until the cause of the alarm is addressed. For example, when the ventilator is running on internal battery, the AC Disconnection alarm may be paused, and the alarm paused symbol will appear until the device is plugged into AC.

• Page 138
  Glossary Battery Level Display of the remaining battery capacity; located adjacent to the battery symbol. Bias flow Turbine flow during exhalation phase through the patient circuit to avoid rebreathing. An abbreviation for “breaths per minute,” which is the unit of measure for breath rate (see below). Breath Rate (Back Up R) The total number of breaths, both machine and spontaneous, delivered by a ventilator in one minute.
• Page 139
  Glossary Fraction of Inspired Oxygen (FIO Amount of oxygen delivered to the patient. Sensor The sensor which measures the amount of oxygen being delivered to the patient. Flow Volume of gas delivered by the ventilator compared to time, expressed in litres per minute (lpm). Flow Pattern (Ramp Setting) This is the flow distribution shape during the inspiration phase.
• Page 140
  Glossary Light Emitting Diode; used as indicator lights on the ventilator’s front panel. Litres Per Minute (a unit of volume flow rate). Machine Hours Counter for the total ventilation time since manufacture or the last CPU board change. Mains AC power supply. Max Leak The maximum alarm setting of a high leakage threshold.
• Page 141
  Glossary Patient Counter Counter of ventilation time for the patient. Patient effort Inspiratory effort initiated by the patient. Patient circuit Tubing between the ventilator and the patient. Pause Waveforms freezing function. PAW (Peak Airway Pressure) The Peak Airway Pressure is the average peak pressure during the inspiratory phase, measured by each cycle and over the previous 24 hour period.
• Page 142
  Glossary Rtot Parameter measured by the ventilator equal to the total number of breaths per minute (bpm). Sensitivity This adjustable parameter determines the amount of inspiratory effort required by the patient before the ventilator delivers an assisted breath, or demands flow in the case of a spontaneous breath.
• Page 143
  Index DEVICE FAULT12….3-10, 3-18 DEVICE FAULT13….3-10, 3-18 AC power DEVICE FAULT3.
• Page 144
  Index utilisation ……3-1 CONNECT VALVE OR CHANGE PRESS alarm message ventilation ……3-1 3-10, 3-17 Alarms tests Connecting to…
• Page 145
  Index Front panel ……2-4 LOW VTl alarm message … . 3-12, 3-23 Heat safety device, battery .
• Page 146
  Index Physical specifications ….A-1 pneumatic……A-8 Placing the ventilator (installing) .
• Page 147
  Index mounting on a wheelchair … . . 4-17 mounting onto a utility cart … . 4-19 parts and accessories ….F-1 patient outlet port connections (figure).

• Page 148: Index

  Index This page intentionally blank Index-6 User’s Manual…

• Page 150
  Part No. 10066883 Rev. B 03/2012 COVIDIEN, COVIDIEN with logo and Covidien logo are U.S. and/or internationally registered trademarks of Covidien AG. ™* Trademark of its respective owner. Other brands are trademarks of a Covidien company. ©2012 Covidien. Covidien llc, 15 Hampshire Street, Mansfield, MA 02048 USA.

Table of Contents

2Ventilator Overview

Table of Contents

3Alarms and Troubleshooting

4Installation and Assembly

Table of Contents

5Operating Procedures

6Internal Battery

7Cleaning

8Routine Maintenance

ASpecifications

Table of Contents

BModes of Ventilation

COperational Verification Checklist

DUnpacking and Preparation

EAlarms Tests

GGlossary

List of Figures

Figure 1-1. Locations of Labels—Top-Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-25 Figure 1-2. Locations of Labels—Front-Left View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-25 Figure 1-3. Location of Labels and Markings—Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-26 Figure 1-4. Location of Labels—Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-26 Figure 2-1. Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Figure 2-2. Back Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6 Figure 2-3. Control Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7 Figure 2-4. Ventilation Menu Display (on standby at left; during ventilation at right) . . . . . . . . . . . . . . . . . . 2-8 Figure 2-5. Alarm Menu (on standby at left; during ventilation at right) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9 Figure 2-6. Waveforms Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10 Figure 2-7. USB Memory Device Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11 Figure 3-1. Front Panel (Alarm Control Key). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Figure 3-2. Alarm Messages (in Ventilation menu at left, in Alarm menu at right) . . . . . . . . . . . . . . . . . . . . . . 3-3 Figure 3-3. Accessing the Alarm Logs Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Figure 3-4. Alarm Logs Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 Figure 3-5. Alarm Logs Screen (no alarm activated). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 Figure 3-6. Pausing the Audible Portion of Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6 Figure 3-7. Ventilator Screen (alarm paused indicator) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7 Figure 3-8. Reactivating Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8 Figure 3-9. Alarm Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8 Figure 4-1. The Power Cable Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 Figure 4-2. Inserting the Power Cable Holder into the Notch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 Figure 4-3. Power Cable Connected to the Ventilator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Figure 4-4. Power Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Figure 4-5. Connecting the DC Power Cable to the Ventilator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7 Figure 4-6. Connecting the Ventilator to an External DC Power Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7 Figure 4-7. Single-Limb Patient Circuit With Exhalation Valve (including accessories). . . . . . . . . . . . . . . . . 4-10 Figure 4-8. Closeup of Exhalation Valve Tube and Proximal Pressure Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11 Figure 4-9. Double-Limb Patient Circuit (including accessories). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12 Figure 4-10. Closeup of Exhalation Valve Tube and Proximal Pressure Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13 Figure 4-11. Close-up of Exhalation Bacteria Filter Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14 Figure 4-12. Single-Limb Patient Circuit Without Exhalation Valve. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14 Figure 4-13. Air Inlet Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16 Figure 4-14. Bacteria Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17 Figure 4-15. Humidifier. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18 Figure 4-16. Removing the Exhalation Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19 Figure 4-17. Rear Panel Oxygen Inlet Port and Coupler. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21 Figure 4-18. Connecting the Oxygen Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22 Figure 4-19. Disconnecting the Oxygen Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23 Figure 4-20. Connecting the FiO2 Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24 Figure 4-21. Using the Dual Bag as a Backpack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26 Figure 4-22. Using the Dual Bag on a Wheelchair (with double-limb circuit on left; with

single-limb circuit on right) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27 Figure 4-23. Using the Dual Bag in a Personal Vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-28

List of Figures

Figure 4-24. Mounting the Ventilator on the Utility Cart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29 Figure 4-25. Securing the Ventilator on the Utility Cart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29 Figure 4-26. Puritan Bennett™ 560 Ventilator Mounted on Utility Cart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-30 Figure 5-1. Turning on the Ventilator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Figure 5-2. VENTILATION ON/OFF Button and Standby Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Figure 5-3. Welcome Menu Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Figure 5-4. Ventilation Menu Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4 Figure 5-5. Selecting the USB Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5 Figure 5-6. Selecting Transfer Continuously . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6 Figure 5-7. Selecting Transfer Trends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7 Figure 5-8. Prompt to Start Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9 Figure 5-9. Starting Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10 Figure 5-10. Stopping Ventilation (1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10 Figure 5-11. Stopping Ventilation (2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11 Figure 6-1. Internal Battery Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3 Figure 6-2. Battery Reserve Capacity as a Percentage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 Figure 6-3. Battery Reserve Capacity in Hours and Minutes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 Figure 6-4. Power Indicators when Charging the Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5 Figure 7-1. Removing the Exhalation Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Figure 7-2. Puritan Bennett ™ 560 Ventilator Pneumatic Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4 Figure 8-1. Blocking the Patient Circuit (single-limb circuit at left; double-limb circuit at right) . . . . . . . . 8-2 Figure 8-2. Calibrating the Exhalation Flow Sensor (1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3 Figure 8-3. Calibrating the Exhalation Flow Sensor (2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3 Figure 8-4. Calibrating the Exhalation Flow Sensor (3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3 Figure 8-5. Calibrating the FiO2 Sensor (1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5 Figure 8-6. Calibrating the FiO2 Sensor (2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5 Figure 8-7. Calibrating the FiO2 Sensor (3). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6 Figure 8-8. Replacing the Air Inlet Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7 Figure E-1. Ventilator Screen (Patient Disconnection alarm shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-2 Figure E-2. Ventilator Screen (High Leakage alarm shown). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-3 Figure E-3. Circuit Check Screen (before starting). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-4 Figure E-4. Blocking the Patient Circuit (single-limb circuit at left; double-limb circuit at right) . . . . . . . . E-5 Figure E-5. Circuit Check (running) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-5 Figure E-6. Circuit Check (complete, passed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-6 Figure E-7. Circuit Check (complete, failed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-6 Figure E-8. Ventilator Screen (AC Power Disconnection alarm shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-8 Figure E-9. Blocking the Patient Circuit (single-limb circuit at left; double-limb circuit at right) . . . . . . . . E-8 Figure E-10. Ventilator Screen (Occlusion alarm shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-9 Figure E-11. Ventilator Screen (AC Power Disconnection alarm shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-10

List of Tables

Table 1-1. Ventilator Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-19 Table 1-2. Ventilator Labels and Markings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-24 Table 3-1. Overview of Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9 Table 3-2. Alarms and Corrective Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16 Table 3-3. Additional Troubleshooting and Corrective Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25 Table 5-1. USB Memory Device Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5 Table 5-2. Ventilator to USB Device Data Transfer Times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8 Table 6-1. Internal Battery Reserve Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 Table 7-1. Approved Cleaning Solutions for Exterior Ventilator Surfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Table 8-1. Preventive Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8 Table A-1. Physical Description (excluding accessories) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1 Table A-2. Electrical Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1 Table A-3. Internal Lithium Ion Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2 Table A-4. Power Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2 Table A-5. Alarm Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2 Table A-6. Audio Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2 Table A-7. Performance Parameter Specifications and Tolerances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3 Table A-8. Monitored Parameter Tolerances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3 Table A-9. Ventilator Range, Resolution, and Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4 Table A-10. Environmental Conditions for Storage or Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-8 Table A-11. Environmental Conditions for Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-8 Table A-12. USB Memory Device Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-8 Table A-13. Data Transfer Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-8 Table A-14. Airway Resistances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-9 Table A-15. Patient Circuit Resistances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-9 Table A-16. Air Inlet Resistance (Filter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-9 Table A-17. Oxygen Inlet Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-9 Table A-18. Performance Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-9 Table A-19. Electromagnetic Emissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-11 Table A-20. Electromagnetic Immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-11 Table A-21. Electromagnetic Immunity—Conducted and Radiated RF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-12 Table A-22. Compliant Cables and Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-12 Table C-1. Operational Verification Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1 Table D-1. Items Included with Ventilator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1 Table F-1. List of Consumables and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-1 Table F-2. List of Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-2

Preface

Purpose of This Manual

This manual contains important information regarding the safe operation of your Puritan Bennett™ 560 ventilator. Your ventilator is an electrical device that can provide years of useful service with the proper care, as described in this manual.

Ensure that you read and understand the instructions contained in this manual before operating the ventilator.

<WARNING:

Before operating the ventilator, read, understand, and strictly follow the information contained in Chapter 1, Safety Information.

Qualification of Personnel

Installation and maintenance of the device must be made by authorized and trained personnel. In particular, training for the handling of products sensitive to electrostatic discharges must include the use of electrostatic discharge (ESD) protection devices and knowledge of the meaning of the symbol at left, as well as using original spare parts and respecting quality assurance and traceability rules approved by Covidien.

Warranty

Information regarding your product warranty is available from your sales representative or Covidien.

Extended Service

The Puritan Bennett™ 560 ventilator offers extended service contracts/warranties for purchase when the ventilator is purchased. Please contact your local Covidien sales or service representative for additional information.

For online technical support, visit the SolvITSM Center Knowledge Base by clicking the link at www.medtronic.com/covidien/support/solvit- center-knowledge-base/. Here, you will find answers to frequently asked questions about the product and other Covidien products 24 hours a day, 7 days a week. If you require further assistance, contact your local Covidien representative.

Service Centers

1Safety Information

1.1Definitions

This manual uses three indicators to highlight critical information: warning, caution, and note. They are defined as follows:

WARNING

Indicates a condition that can endanger the patient or the ventilator operator.

Caution

Indicates a condition that can damage the equipment.

Note

Indicates points of particular emphasis, that make operation of the ventilator more efficient or convenient.

It is essential to read, understand and follow these instructions before using the Puritan Bennett™ 560 ventilator.

In order to use the ventilator correctly and efficiently and to help prevent incidents, please pay particular attention to section 1.2, Warnings, as well as all warnings and cautions contained throughout this manual.

:Note:

Many ventilator functions are not accessible when the Locking key is enabled. For additional assistance contact your clinician or equipment representative.

1.2Warnings

1.2.1General Warnings Regarding Use of Equipment

<WARNING:

The ventilator must be used only under the responsibility and on the prescription of a doctor.

<WARNING:

The ventilator must be used according to its intended use. Refer to section 2.1, Indications for Use.

<WARNING:

Be aware this manual describes how to respond to the ventilator, but does not tell you how to respond to the patient.

<WARNING:

While the ventilator is in use, an alternative means of ventilation should always be available in the event of a ventilator problem. This is particularly true for ventilator-dependent patients. Supplementary observation, appropriate for the patient’s condition, is also recommended.

<WARNING:

To ensure that ventilation continues uninterrupted, ensure alternative power sources are available (AC power source, extra batteries, or an auxiliary DC car adapter). Be prepared for the possibility of power failure by having an alternative means of ventilation ready for use—particularly for ventilatordependent patients.

<WARNING:

Do not allow a patient to remain connected to the ventilator when ventilation is stopped, because a substantial quantity of exhalation gas, primarily carbon dioxide, may be inhaled by the patient. In some circumstances, inhaling carbon dioxide may lead to under-ventilation, suffocation, and serious injury or death.

<WARNING:

Always have immediate access to an alternative means of ventilation, which is ready for use, to avoid patient death or serious injury.

<WARNING:

The ventilator must not be used with flammable anesthetic substances.

<WARNING:

Do not start ventilation until you ensure that the device is suitably assembled, that the air inlet filter is properly installed and is not obstructed, and that there is proper clearance all around the unit. Also ensure that the patient circuit is suitably connected to both the ventilator and the patient and that the patient circuit, including all hoses, is not damaged or obstructed.

<WARNING:

A ventilator-dependent patient should always be monitored by trained and competent medical personnel. Ensure that the patient’s caregiver is able and prepared to take suitable action in the event the ventilator identifies an alarmed condition or experiences a problem.

<WARNING:

Do not use a patient circuit with a leak accessory for ventilator-dependent patients.

Warnings

<WARNING:

Refer to this manual for equipment compatible with this ventilator. It may be unsafe to interconnect this equipment with other equipment not described in this manual.

<WARNING:

Before dispensing the ventilator to caregivers or the patient for home use, ensure the Locking Key is activated so that critical ventilator settings are not modified.

<WARNING:

Do not perform ventilator alarm tests while the patient is connected to the ventilator. Provide the patient with an alternate means of ventilation before conducting these tests.

<WARNING:

Verify the functionality of the alarms before connecting the patient to the ventilator. Refer to Appendix

E, Alarms Tests.

<WARNING:

If the ventilator fails the alarm tests or if you cannot complete the tests, refer to Chapter 3, Alarms and Troubleshooting or call your equipment supplier or Covidien.

<WARNING:

When an alarm condition is triggered, or there is evidence of a patient-ventilator fault or problem, examine the patient first before examining the ventilator.

<WARNING:

A continuous alarm condition will be activated if the ventilator power switch is turned off while ventilation is in progress. When the power switch is turned back on again, ventilation will resume without having to press the VENTILATION ON/OFF button.

<WARNING:

To reduce the risk of infection, wash your hands thoroughly before and after handling the ventilator or its accessories.

<WARNING:

A patient treated by mechanical ventilation is highly vulnerable to the risks of infection. Dirty or contaminated equipment is a potential source of infection. Clean the ventilator and its accessories regularly and systematically before and after each use and following any maintenance procedure to reduce the risks of infection. The use of a bacterial filter at the ventilator’s outlet (TO PATIENT) port—or both ports if a double-limb circuit is used—is recommended. Refer to Chapter 7, Cleaning.

<WARNING:

Handle the ventilator with care during and after use, particularly when ambient temperatures are high. Some ventilator surfaces may become hot, even if safety specifications are not exceeded.

<WARNING:

Do not connect the ventilator to any device other than a PC with a dedicated compatible Puritan Bennett™ software package.

<WARNING:

The ventilator system is not intended to be a comprehensive monitoring device and does not activate alarms for all types of conditions. For a detailed understanding of ventilator operations, be sure to thoroughly read this manual before attempting to use the ventilator system.

1.2.2Warnings Regarding Installation and Environment of Use

<WARNING:

Even though the Puritan Bennett™ 560 ventilator meets current safety standards, the internal Lithiumion battery of the device exceeds the 100Wh threshold and is therefore considered to be Dangerous Goods (DG) Class 9 – Miscellaneous, when transported in commerce. As such, the Puritan Bennett™ 560 ventilator and/or the associated Lithium-ion battery are subject to strict transport conditions under the Dangerous Goods Regulation for air transport (IATA: International Air Transport Association), International Maritime Dangerous Goods code for sea and the European Agreement concerning the International Carriage of Dangerous Goods by Road (ADR) for Europe. Private individuals who transport the device are excluded from these regulations although for air transport some requirements apply. For air transport; the Puritan Bennett™ 560 ventilator is permitted as checked-in or carry-on baggage. Two spare batteries per person may be taken on board as carry-on luggage only, with the prior approval of the airline. This classification and regulatory requirements may vary depending upon the country and mode of transport. Therefore it is recommended that users verify with the carrier / airline as to which measures to take before the voyage.

<WARNING:

To minimize the risk of damage, you must use the ventilator’s dual bag to transport the ventilator. Ventilator accessories are listed in Table F-1.

<WARNING:

When using the ventilator in a carrying case, only use a carrying case that is listed in the instructions for use to prevent adverse ventilator performance, which can consequently result in patient death.

<WARNING:

Regularly clean the ventilator’s dual bag according to manufacturer’s recommendations.

<WARNING:

The ventilator should never be immersed in any liquid, and any liquid on the surface of the device should be wiped away immediately.

Warnings

<WARNING:

To avoid damage to the ventilator, in particular the batteries or electrical components, fluids must not be allowed to enter the device, particularly through the air inlet filter or the cooling apertures located in the side, rear, and bottom panels of the ventilator.

<WARNING:

To ensure correct and lasting operation of the device, ensure that the ventilator is installed and operated in the environmental conditions recommended in Appendix A, Specifications.

<WARNING:

Do not leave power cables lying on the ground where they may pose a hazard.

<WARNING:

Do not operate the ventilator in a magnetic resonance imaging (MRI) environment. Doing so could cause a ventilator malfunction.

<WARNING:

Do not operate the ventilator in the presence of active high frequency (HF) surgical equipment. Doing so could cause a ventilator malfunction.

<WARNING:

Do not operate the ventilator in direct sunlight, near heat sources, outdoors, or near installations where liquid may pose a risk without first providing adequate protection for the device.

<WARNING:

Avoid using the ventilator, if possible, in dusty environments. Dusty environments may require more vigilant monitoring, cleaning, and/or replacement of air intake and other filters.

<WARNING:

Ensure that the ventilator’s immediate surroundings allow for the proper operational connection of the device without folding, pinching, or damaging any of the required cables or tubes, and that the connection of the patient circuit to the patient provides for a secure, comfortable fit.

<WARNING:

Ensure that the ventilator is not positioned or located such that the AC and DC connections at the back of the ventilator are difficult to access.

<WARNING:

Do not cover the ventilator or place in a position that affects proper operation, e.g., blocking a front or lateral opening.

<WARNING:

Place the ventilator in a safe place when ventilating and according to the recommendations in this manual.

<WARNING:

Do not place the ventilator in a position where a child, pet or pest can reach it, or in any position that might cause it to fall on the patient or someone else.

<WARNING:

To ensure correct and lasting operation of the ventilator, ensure that its air circulation holes (main inlet or cooling) are never obstructed. Place the device in an area where air can freely circulate around the ventilator and avoid installing it near floating fabrics, such as curtains.

<WARNING:

If the ventilator has been transported or stored at a temperature that differs more than ±20°C (±36°F) from the temperature in which it will be operating, the ventilator should be allowed to stabilize in its operating environment for at least 2 hours prior to use. When the ambient temperature is 20°C, 2 hours are required to warm the ventilator from the minimum storage temperature or to cool the ventilator from the maximum storage temperature prior to use.

<WARNING:

If the ambient temperature where the device is operated is greater than 35°C (95°F), the temperature of the patient circuit or the flow supplied at the device outlet may exceed 41°C (106°F), and the patient circuit may reach up to 60°C (140°F). This may lead to undesirable side effects for the patient. To avoid injury to the patient move the patient and the ventilator to a cooler location. For more information, contact Covidien.

<WARNING:

The default setting for altitude compensation is YES. Altitude compensation should always be set to YES for accurate volume delivery calculations at all elevations.

<WARNING:

To reduce the risk of a fire hazard, keep matches, lighted cigarettes, and all other sources of ignition (such as flammable anesthetics and/or heaters) away from the ventilator and oxygen hoses.

<WARNING:

Regularly check the cleanliness of the air inlet filter located on the rear of the ventilator. If necessary, replace the filter before the recommended replacement period is over (see Chapter 8, Routine Maintenance). This is particularly important when the ventilator is installed on a wheelchair, because environmental conditions may cause the filter to become dirty more rapidly.

<WARNING:

Handle the ventilator with care during and after use, particularly when ambient temperatures are high. Some ventilator surfaces may become hot, even if safety specifications are not exceeded.

Warnings

<WARNING:

Exercise care to avoid any potential significant risks of reciprocal interference posed by the ventilator and accessories during specific investigations or treatments.

1.2.3Warnings Regarding Electrical Power Supplies

<WARNING:

The operator should connect the ventilator to an AC power source whenever available, for safer operation.

<WARNING:

The maximum recommended shelf life of the internal battery is 2 years. Do not use a battery that has been stored for 2 years prior to its first use.

<WARNING:

Periodic recharging is important to help maximize useful life of the battery. Do not store the internal battery for extended periods, without recharging, as this may reduce the maximum life.

<WARNING:

For the AC (“mains”) power cable to be properly secured, the attachment located on the power cable must be fitted into the power cable holder incorporated in the battery access cover and located under the AC (mains) power socket. Refer to section 4.2, Connecting to External AC Power.

<WARNING:

The power supply to which the ventilator is connected (both AC and DC) must comply with all applicable standards and provide electrical power corresponding to the voltage characteristics inscribed on the rear of the ventilator to ensure correct operation. Refer also to the electrical specifications found in Appendix A, Specifications.

<WARNING:

Ensure that the ventilator’s internal battery is fully charged before connecting the ventilator to an external DC power source. Powering the ventilator using an external 12–30 VDC power source (via the DC power cable) does not enable its internal battery to recharge.

<WARNING:

Due to the internal battery’s limited reserve capacity, the ventilator should only be operated on the internal battery when no other power source is available. Ensure that the internal battery never becomes fully discharged.

<WARNING:

When using a car auxiliary adapter (cigarette lighter) ensure the car has been started prior to plugging in the ventilator’s DC adapter. Refer to section 4.3, Connecting to an External DC Power Source.

<WARNING:

Even if the internal battery charging indicator is off, charging of the battery may sometimes be incomplete if the ambient temperature is above 40°C (104°F) because of the battery’s internal heat safety device.

<WARNING:

When the Low Battery alarm is triggered, immediately connect the ventilator to an AC power supply to maintain ventilation and recharge the internal battery.

<WARNING:

Batteries should be disposed of according to environmental legislation in your country and locality.

<WARNING:

Never expose any batteries to direct flame.

<WARNING:

Ensure that the AC power cable is in perfect condition and not compressed. The device should not be turned on if the AC power cable is damaged.

1.2.4Warnings Regarding Hoses and Accessories

<WARNING:

The ventilator must not use, nor be connected to, any anti-static or electrically conductive hoses, tubing, or conduits.

<WARNING:

Minimum and maximum VTE alarm parameters must be properly set to warn in the event of patient disconnection.

<WARNING:

Before opening the packaging for the patient circuit, ensure that no damage is evident to the packaging or its contents. Do not use if evidence of damage exists.

<WARNING:

The patient circuit should not be changed during ventilation.

<WARNING:

On a DAILY basis, inspect the patient circuit to ensure that it shows no signs of damage, is properly connected, and is operating correctly without leakage.

<WARNING:

Single use accessories should not be reused.

Warnings

<WARNING:

The exhalation block is intended for single use by a single patient . It may periodically be cleaned, but it cannot be disinfected or sterilized. To maintain good measurement quality when used continuously, clean the exhalation block periodically (refer to section 7.3, Cleaning the Exhalation Block). The exhalation block should be changed every 4 months and cannot be reused with any other patient.

<WARNING:

During invasive ventilation (when an artificial airway bypasses the patient’s upper respiratory system), the patient’s upper respiratory system cannot humidify the incoming gas. For this reason, a humidifier, to minimize drying of the patient’s airway and subsequent irritation and discomfort, must be used.

<WARNING:

If exhaled tidal volume measurements are required to ensure correct patient ventilation a double-limb patient circuit configuration must be used in order to detect leaks. In this case, both the minimum and maximum VTE alarm parameters must be properly set to warn in the event of patient disconnection.

<WARNING:

Failing to replace a dirty air inlet filter or operating the ventilator without a filter may cause serious damage to the ventilator.

<WARNING:

Before cleaning the ventilator, first disconnect the ventilator and the patient circuit.

<WARNING:

If the ventilator is used indoors, the condition of the air inlet filter should be checked monthly. If the ventilator is used outdoors or in a dusty environment, the filter should be checked weekly and replaced as necessary.

<WARNING:

The air inlet filter is not reusable; do not attempt to wash, clean, or reuse it.

<WARNING:

The patient circuit should always be positioned to avoid hindering the patient’s movements, to prevent accidental disconnection or leakage, and to minimize the risk of patient strangulation.

<WARNING:

For pediatric use, ensure that the patient circuit type fits, and, in all respects, is suitable for use with a child. Use a pediatric circuit for patients that weigh under 53 lb. (23 kg). To ensure proper performance of the ventilator, use a recommended patient circuit; see Table F-2.

<WARNING:

Resistance of the exhalation valve and accessories (water traps, filters, HMEs, etc.) must be as low as possible.

<WARNING:

Adding attachments to the ventilator breathing system can cause the pressure during exhalation at the patient connection port to increase.

<WARNING:

The exhalation valve must allow rapid discharge of the circuit pressure. Ensure that the exhalation valve is always clean and its evacuation aperture (exhaust port) is never obstructed.

<WARNING:

Users must always possess an additional breathing circuit and exhalation valve while using the Puritan Bennett™ 560 ventilator.

<WARNING:

Always ensure that the humidification device is positioned lower than both the ventilator and the patient. Use water traps, if necessary, to limit water in the patient circuit and periodically empty these water traps. Take precautions when discarding the fluid in the water trap. Discard per local ordinance for proper disposal.

<WARNING:

Use of a nebulizer or humidifier can lead to an increase in the resistance of inspiratory and exhalation filters. Monitor the filters frequently for increased resistance or blockage.

<WARNING:

If a heated humidifier is used, you should always monitor the temperature of the gas delivered to the patient. Gas delivered from the ventilator that becomes too hot may burn the patient’s airway.

<WARNING:

Adding accessories to the ventilator breathing circuit, such as a humidifier and water trap(s), may result in a decrease in tidal volume delivered to the patient due to the added compressible volume of the accessory. Always assure that the patient is receiving the appropriate inspired volume when altering the breathing circuit configuration.

<WARNING:

The level of inspiratory resistance of the circuit and accessories (bacteria filter, humidifier, HMEs, etc.) must be as low as possible. Settings—particularly the Patient Disconnection alarm, maximum inspired volume (Max VTI), and minimum inspired volume (Min VTI) settings—must be periodically adjusted according to changes in the patient circuit resistance—especially when filters are replaced.

<WARNING:

To ensure proper performance of the ventilator, use a patient circuit recommended by Covidien in this manual; refer to Chapter 4, Installation and Assembly and Appendix F, Parts and Accessories. The total specified length of the patient circuit tubing as measured from the ventilator outlet to the ventilator inlet is 1.1 meters (3.6 feet) to 2.0 meters (6.6 feet). The tubing must conform to all applicable standards and must be fitted with Ø 22 mm terminals that also conform to all applicable standards. Ensure that

Warnings

both the length and the internal volume of the patient circuit are appropriate for the tidal volume: a corrugated tube of Ø 22 mm for adult patients, and a corrugated tube of Ø 15 mm for pediatric patients with a tidal volume lower than 200 ml.

<WARNING:

To ensure proper performance of the ventilator, use only accessories (including oxygen accessories) approved and recommended by Covidien. See Appendix F, Parts and Accessories or contact your customer services.

<WARNING:

To reduce the likelihood of disconnection and to prevent adverse ventilator performance, use only accessories compatible with the ventilator. Compatibility is determined by reviewing the instructions for use of either the ventilator or the accessories.

<WARNING:

When using non-invasive ventilation (NIV) without an exhalation valve, use a vented nose or face mask or a non vented combined with a leak accessory. When using non-invasive ventilation (NIV) with an exhalation valve, use a non-vented mask.

1.2.5Warnings Regarding Settings

<WARNING:

Before starting ventilation, always verify that all settings are properly set in accordance with the required prescription.

<WARNING:

Before starting ventilation, ensure that the device is properly assembled and that the air inlet, cooling vents, and alarm sound diffusion holes are not obstructed. Ensure also that the patient circuit is of the proper configuration (double or single limb), properly connected to the ventilator, and that the circuit hoses are neither damaged nor compressed and contain no obstructions or foreign bodies.

<WARNING:

The CPAP mode does not provide a set respiratory rate. Do not use this mode for ventilator-dependent patients.

<WARNING:

Do not allow a patient to remain connected to the ventilator when ventilation is stopped, because a substantial quantity of exhalation gas, primarily carbon dioxide, may be inhaled by the patient.

<WARNING:

Alarm volume should be adjusted with respect to the ventilator’s operating environment and so that the patient’s caretakers can hear the alarms. The audible alarm vents located at the front of the device should never be obstructed. The alarm can be paused with the Alarm Pause function by pressing the ALARM CONTROL key twice once the alarm has been declared.

<WARNING:

Ensure that the I Sens setting is not set to OFF when ventilating patients capable of triggering spontaneous breaths.

<WARNING:

The ventilator offers a variety of breath delivery options. Throughout the patient’s treatment, the clinician should carefully select the ventilation mode and settings to use for that patient, based on clinical judgment, the condition and needs of the patient, and the benefits, limitations, and characteristics of the breath delivery options. As the patient’s condition changes over time, periodically assess the chosen modes and settings to determine whether those are best for the patient’s current needs.

<WARNING:

In adult or pediatric use ensure that the adjusted tidal volume is compatible with the needs of the patient.

<WARNING:

When changing the mode during ventilation, significant transitions of pressure, flow or cycling rate might occur, depending on the difference between the modes. Before setting the new mode, first ensure that the settings between the different modes are compatible. This reduces the risk of discomfort and harm to the patient.

<WARNING:

Do not conduct the ventilator alarm test while the patient is connected to the ventilator. Switch the patient to an alternate means of ventilation before testing.

<WARNING:

The Min PIP alarm setting must be adjusted for the patient, but must also be set high enough to allow the Patient Disconnection alarm to trigger properly. Perform the low pressure test to ensure the alarm is properly set.

<WARNING:

The Max Leak alarm setting must be adjusted for the patient, but must also be set low enough to allow the High Leakage alarm to trigger properly. Perform the max leak test to ensure the alarm is functioning properly. This alarm only applies to leak configuration (NIV).

<WARNING:

If Apnea Time is set to a value higher than 60/Control R then the Apnea alarm will not activate.

<WARNING:

If an Apnea alarm is required, set the Apnea setting to YES in the Preferences Menu.

Warnings

<WARNING:

The Apnea alarm should be set to YES for ventilator dependent patients.

<WARNING:

Setting any alarm limits to OFF or extreme high or low values can cause the associated alarm not to activate during ventilation, which reduces its efficacy for monitoring the patient and alerting the clinician to situations that may require intervention.

<WARNING:

Ensure the Insp Time setting is compatible with the physiological requirements of the patient.

<WARNING:

Adjustable alarms should not be systematically canceled; instead, they should be adjusted according to the needs and condition of the patient.

<WARNING:

Do not pause, disable, or decrease the volume of the ventilator’s audible alarm if patient safety could be compromised.

<WARNING:

A continuous alarm condition will be activated if the ventilator power switch is turned off while ventilation is in progress. When the power switch is turned back on again, the ventilation will resume without having to press the VENTILATION ON/OFF button.

<WARNING:

In the SIMV mode the use of a double-limb circuit is recommended. The Min VTE setting should remain active in the event that pressure losses are present on the patient circuit downstream from the proximal pressure link. In such cases the Patient Disconnection alarm would not be systematically activated in case of a disconnection of the circuit.

<WARNING:

The inspiration trigger threshold should be carefully modified in order to avoid the risk of false triggering or “autotriggering” of the ventilator. For example, Level 0P, the most sensitive mode, is recommended for pediatric use. However, for an adult, this setting may result in autotriggering.

<WARNING:

The sound level of the alarms should be adjusted according to the installation environment and the size of the area monitored by the patient’s caregiver. Ensure that the alarm sound apertures at the front of the device are never obstructed.

1.2.6Warnings Regarding PC Connection and USB Memory Devices

<WARNING:

Do not connect the ventilator to any device other than a PC with a dedicated compatible Puritan Bennett™ software package.

<WARNING:

Always verify the file ID before using a USB memory device to transfer data between the ventilator and a PC.

<WARNING:

USB connections are not intended for connection to any devices other than the specified USB flash storage (see section 5.2.1, USB Memory Device Specifications).

1.2.7Warnings Regarding Maintenance

<WARNING:

Never use a ventilator or any components or accessories that appear to be damaged. If any signs of damage are evident, contact your equipment supplier or Covidien.

<WARNING:

To ensure proper servicing and avoid the possibility of physical injury to personnel or damage to the ventilator, only personnel authorized and qualified by Covidien should attempt to service or make authorized modifications to the Puritan Bennett™ 560 ventilator.

<WARNING:

If you cannot determine the cause of a problem with your ventilator, contact your equipment supplier. Do not use the ventilator until the problem has been corrected.

<WARNING:

To ensure proper performance of the ventilator, the preventative maintenance schedule should be followed. For further information contact Covidien.

<WARNING:

On a daily basis, ensure the proper connection and operation of the patient circuit.

<WARNING:

If a problem with the ventilator is suspected, FIRST CHECK THAT THE PATIENT IS NOT IN DANGER. If necessary, remove the patient from the ventilator and provide an alternative means of ventilation.

Warnings

<WARNING:

After assembling, cleaning, or reassembling the patient circuit, and on a daily basis, inspect the hoses and other components to ensure that there are no cracks or leaks and that all connections are secure.

<WARNING:

Use all cleaning solutions and products with caution. Read and follow the instructions associated with the cleaning solutions you use to clean your ventilator. Use only those solutions listed in Table 7-1.

<WARNING:

Never use a liquid cleaner inside the patient circuit, or on any component of a gas pathway. Clean the patient circuit only as specified by the manufacturer’s instructions.

<WARNING:

Do not attempt to open, repair or otherwise service the ventilator yourself. Doing so might endanger the patient, damage the ventilator, or void your warranty. Only personnel authorized and qualified by Covidien should repair, open or service the ventilator.

<WARNING:

If the ventilator is damaged, or its external housing is not correctly closed, or it behaves in a way that is not described in this manual (excessive noise, heat emission, unusual odor, alarms not triggered during the start-up procedure), the oxygen and power supplies should be disconnected and use of the device stopped immediately.

<WARNING:

The exhalation block is intended for single use by a single patient . It may periodically be cleaned, but it cannot be disinfected or sterilized. To maintain good measurement quality when used continuously, clean the exhalation block periodically (refer to section 7.3, Cleaning the Exhalation Block). The exhalation block should be changed every 4 months and cannot be reused with any other patient.

<WARNING:

Ensure that the exhalation block is completely dried after cleaning and prior to use.

<WARNING:

When an exhalation block is set up, each time it is removed, or after installing a new exhalation block on the machine, it is essential that the exhalation flow sensor be recalibrated before the exhalation block is used. Refer to section 8.3, Calibrating the Exhalation Flow Sensor.

<WARNING:

The patient circuit is intended for single use by a single patient and should be changed according to the manufacturer’s recommendations and according to the patient circuit lifetime. Refer to the instructions for use supplied by the manufacturer of the patient circuit (included with the ventilator) and Chapter 4, Installation and Assembly.

<WARNING:

A patient treated by mechanical ventilation is highly vulnerable to the risks of infection. Dirty or contaminated equipment is a potential source of infection. Clean the ventilator and its accessories regularly and systematically before and after each use and following any maintenance procedure to reduce the risks of infection. The use of a bacterial filter at the ventilator’s outlet (TO PATIENT) port—or both ports if a double-limb circuit is used—is recommended. Refer to Chapter 7, Cleaning.

<WARNING:

Regularly check the cleanliness of the air inlet filter located on the rear of the ventilator. If necessary, replace the filter before the recommended replacement period is over (see Chapter 8, Routine Maintenance). This is particularly important when the ventilator is installed on a wheelchair, because environmental conditions may cause the filter to become dirty more rapidly.

<WARNING:

For environmental protection, the ventilator and its components, whatever their respective conditions of operation, cannot be disposed of with household waste and must be submitted for suitable selective collection and possible recycling. Observe all applicable regulations when disposing of the ventilator and any of its components.

<WARNING:

Before using the ventilator’s internal battery, ensure that the battery is fully charged and that the charge holds. Back up ventilators or those in storage should be connected to an AC power source to protect the integrity of the battery.

<WARNING:

The maximum recommended shelf life of the internal battery is 2 years. Do not use a battery that has been stored for 2 years prior to its first use. Periodic recharging is important to help maximize useful life of the battery. Do not store the internal battery for extended periods, without recharging, as this may reduce the maximum life.

<WARNING:

To connect the ventilator to an external power source, first ensure the ventilator’s I/O (power) switch is off (O). Then, connect the desired power cable to the ventilator. Finally, connect the power cable to the external power source.

<WARNING:

To disconnect the ventilator from an external power source, first power down the ventilator. Then, disconnect the power cable from the external power source and, finally, the ventilator.

<WARNING:

Connect the external DC power source by first connecting the power cable to the ventilator and then to the external DC source. Follow the reverse procedure to disconnect the device from the external DC power source.

Warnings

<WARNING:

Connect the external electrical power source by first connecting the power cable to the ventilator and then to the external power source. Follow the reverse procedure to disconnect the device from electrical power sources.

1.2.8Warnings Regarding Oxygen

<WARNING:

The ventilator must not be used with flammable anesthetic substances.

<WARNING:

Oxygen therapy for patients with respiratory failure is a common and effective medical prescription. However, be aware that inappropriate oxygen use may potentially lead to serious complications, including, but not limited to, patient injury.

<WARNING:

Strictly follow the instructions provided in section 4.8.2, Connecting the Oxygen Supply, which include the use of a flow regulator and special oxygen connector.

<WARNING:

To avoid injury to the patient and/or possible damage to the ventilator: before connecting the ventilator to the oxygen supply, ensure a flow meter (flow regulator) is connected to the ventilator to regulate the oxygen supply to the required specification.

<WARNING:

The Puritan Bennett™ 560 ventilator can be used with an optional oxygen analyzer with minimum and maximum concentration alarms. Always measure the delivered oxygen with a calibrated oxygen analyzer (FiO2 kit) that features a minimum and maximum concentration alarm in order to ensure that the prescribed oxygen concentration is delivered to the patient.

<WARNING:

The Puritan Bennett™ 560 ventilator is designed to deliver a percentage of oxygen equal or lower than 50%. Do not exceed this value as this may cause the ventilator to malfunction and put the patient at risk.

<WARNING:

Ensure that the oxygen supply pressure to the machine never exceeds 7 psi (50 kPa) or a flow of 15 lpm. For volume and sensitivity tolerances, refer to Table A-7.

<WARNING:

In the event of an oxygen leak, shut down the supply of oxygen at its source. In addition, remove and/ or keep any incandescent source away from the device, which may be enriched with oxygen. Circulate fresh air into the room to bring the oxygen level down to normal.

<WARNING:

The hose connecting the ventilator to the oxygen source must be designed exclusively for use with medical-grade oxygen. Under no circumstances should the oxygen hose be modified by the user. In addition, the hose must be installed without the use of lubricants.

<WARNING:

Ensure that the only gas supplied to the ventilator through the dedicated oxygen supply connector is medical-grade oxygen.

<WARNING:

The coupler must not remain connected to the oxygen inlet unless it is also connected to a leakproof, external oxygen gas source. When an oxygen supply is not being used with the ventilator, disconnect the oxygen source completely from the ventilator.

<WARNING:

To prevent any interference with the internal sensors of the ventilator, do not install a humidifier upstream of the ventilator.

<WARNING:

To ensure stability, when the Puritan Bennett™ 560 ventilator is mounted on a cart, the weight of the oxygen bottle should not exceed 14 kg (30 lbs).

<WARNING:

The oxygen supply hose ages even when it is not in use and should be replaced periodically. Follow the expiration date, if any.

<WARNING:

The oxygen supply must be regulated using a flow meter connected to the source gas outlet.

<WARNING:

The oxygen supply must be shut off when ventilation is interrupted. Before disconnecting the oxygen hose, allow the ventilator to continue for a few cycles without oxygen to flush the patient circuit of excess oxygen.

<WARNING:

Before connecting the oxygen supply, ensure that the stud on the oxygen inlet is protruding outwards.

<WARNING:

Inspect the oxygen coupler before use to ensure it has its black O-ring attached and in good condition. Do not use an oxygen coupler with a missing, damaged, or worn O-ring.

Symbols and Markings

1.2.9Warnings Regarding Electromagnetic Interference

<WARNING:

The Puritan Bennett™ 560 ventilator requires special precautions for electromagnetic compatibility and should be installed and started according to the recommendations found in Appendix A, Specifications. In particular, the use of nearby mobile and portable communications equipment using radio frequencies, such as mobile telephones or other systems exceeding the levels set in the IEC 60601-1-2 standard, may affect its operation. Refer to section A.10, Manufacturer’s Declaration.

<WARNING:

Portable RF communications equipment (including peripherals such as antenna cables and external antennas) should be used no closer than 30 cm (12 inches) to any part of the ventilator, including cables specified by the manufacturer. Otherwise, degradation of the performance of this equipment could result.

<WARNING:

The use of any accessory other than those specified, with the exception of the power supplies or cables sold by Covidien, may lead to an increase in electromagnetic emissions or a decrease in the equipment protection against electromagnetic emissions. If the ventilator is used adjacent to such accessories or stacked with such devices, the ventilator’s performance should be monitored to verify normal operation.

1.3 Symbols and Markings

Table 1-1. Ventilator Symbols

Symbols Descriptions

It is essential to read, understand, and follow these instructions before using the Puritan Bennett™ 560 ventilator (ISO 7000-0434A).

This symbol appears on the ventilator’s back panel, see item 5 in Table 1-2.

It is mandatory to read, understand, and follow these instructions before using the Puritan Bennett™ 560 Ventilator (ISO 7010-M002). This symbol appears on the ventilator’s air inlet label, see item 5 in Table 1-2.

Type BF applied part (IEC 60417-5333).

A regulatory standard classification for protection against electrical shock for the part of the device that contacts the patient.

This symbol appears on the ventilator’s back panel; see item 5 in Table 1-2.

Direct current, DC (IEC 60417-5031).

This symbol appears on the ventilator’s front panel and back panel; see Figure 1-1, and item 9 in Figure 1-3.

Alternating current, AC (IEC 60417-5032).

This symbol appears on the ventilator’s front panel and back panel; see item 8 in Figure 1-3, and item 10 in

Figure 2-3 (page 2-7).

Internal battery.

This symbol appears on the ventilator’s front panel; see item 10 in Figure 2-3 (page 2-7).

Table 1-1. Ventilator Symbols (Continued)

Symbols Descriptions

Insulation class II equipment (IEC 60417-5172).

A regulatory standard classification for protection against electric shock. Class II equipment relies on double insulation rather than protective earthing.

This symbol appears on the ventilator’s back panel; see item 5 in Table 1-2.

Index of Protection rating for the ventilator’s enclosure, defined in IEC 60529 (BSEN60529).

The first digit, 3, indicates protection against the intrusion of small foreign bodies (including fingers, tools, wires, etc. with a diameter greater than 2.5 mm) into the ventilator. The second digit, 2, indicates protection against water dripping or falling vertically when the enclosure is tilted at an angle up to 15° from its normal position, as well as an environment featuring water vapor condensation and/or light rain.

This rating appears on the ventilator’s back panel; see item 5 in Table 1-2.

CSA—Canadian Standards Association.

This symbol appears on the ventilator’s back panel; see item 5 in Table 1-2.

CE—Conformity European

Signifies compliance with the medical device directive 93/42/EEC as amended by 2007/47/EC.

This symbol appears on the ventilator’s back panel; see item 5 in Table 1-2.

This combined symbol appears on the ventilator’s UP/UNFREEZE key; see item 4 in Figure 2-3 (page 2-7).

This key is used to: move the LCD display’s cursor upwards, line-by-line; increase the value of displayed and selected parameter settings; restart (“unfreeze”) waveforms tracing.

This combined symbol appears on the ventilator’s DOWN/FREEZE key; see item 6 in Figure 2-3 (page 2-7).

This key is used to: move the LCD display’s cursor downwards, line-by-line; decrease the value of displayed and selected parameter settings; stop (“freeze”) waveforms tracing.

This symbol appears on the ventilator’s ENTER key; see item 5 in Figure 2-3 (page 2-7).

This key is used to confirm command actions.

This combined symbol appears on the ventilator’s ALARM CONTROL key; see item 2 in Figure 2-3 (page 2-7).

This key is used to: cancel the audible portion of alarms for 60 seconds at a time; cancel an alarm.

For more information, see Appendix E, Alarms Tests.

This symbol appears on the ventilator’s MENU key; see item 7 in Figure 2-3 (page 2-7).

This key is used to access the ventilator’s menus via the ventilator’s front panel LCD display.

This symbol (IEC 60417–5009) appears on the ventilator’s VENTILATION ON/OFF button; see item 8 in Figure 2-3 (page 2-7).

This button is used to start and stop ventilation.

TO PATIENT port.

This symbol appears on the front right of the ventilator, adjacent to the TO PATIENT port; see item 1 in Figure 1-1.

FROM PATIENT port (double-limb option).

This symbol appears on the front left of the ventilator, adjacent to the FROM PATIENT port; see item 4 in Figure 1-1.

Patient proximal pressure port.

This symbol appears on the front right of the ventilator, adjacent to the proximal pressure and TO PATIENT ports; see Figure 1-1, and item 3 in Figure 1-4.

Symbols and Markings

Table 1-1. Ventilator Symbols (Continued)

Symbols Descriptions

Exhalation valve pilot port.

This symbol appears on the front right of the ventilator, adjacent to the exhalation valve and TO PATIENT ports, indicating the connection of the tubing between the patient circuit exhalation valve; see Figure 1-1, and item 3 in Figure 1-4.

Oxygen inlet.

This marking appears on the back panel of the ventilator, adjacent to the oxygen inlet port; see item 2 in Figure 1-3.

Nurse call connection.

This symbol appears on the back panel of the ventilator, adjacent to the nurse call receptacle; see item 12 in

Figure 1-3.

Note: Nurse call is not intended for use in the home environment.

Switch in “Off” position (IEC 60417-5008).

This symbol appears on the I/O (power on/off) switch on the back panel of the ventilator to indicate the switch’s “Off” position. See item 2 in Figure 2-2 (page 2-6).

Switch in “On” position (IEC 60417-5007).

This symbol appears on the I/O (power on/off) switch on the back panel of the ventilator to indicate the switch’s “On” position. See item 2 in Figure 2-2 (page 2-6).

Software lock enabled.

This symbol appears at upper left in the ventilator’s LCD display when the keyboard Locking key is enabled.

Internal battery.

This symbol appears at top center in the ventilator’s LCD display to indicate that the ventilator is being powered by its internal battery. See item 1 in Figure 2-4 (page 2-8), and Chapter 6, Internal Battery, for more information.

Pressure rise times (inspiratory phase) parameter.

These symbols appear on the ventilation mode menu screens. In pressure ventilation modes, you can select one of four rise times with setting 1 representing the fastest rise time and setting 4 representing the slowest.

Flow shape (“flow distribution shape”, inspiratory phase) parameter.

These symbols appear on the ventilation mode menu screens; selectable for V A/C mode only. In volume ventilation mode you can select between Square (SQ), Descending (D) or Sinusoidal (S) flow patterns.

Selected line (filled square).

When making menu choices, this graphic indicates the line on which the cursor is currently positioned.

Non-selected line (empty square).

When making menu choices, this graphic indicates a line on which the cursor is currently not positioned.

Locked parameter line.

When making menu choices, this graphic indicates a line that cannot be selected (the Locking key is enabled).

Active parameter line.

When making menu choices, this graphic indicates that the current parameter is selected and can be changed. See Chapter 5, Operating Procedures.

Table 1-1. Ventilator Symbols (Continued)

Symbols Descriptions

Inspiratory effort detected.

This symbol appears in the front panel display’s Status window when the patient triggers a breath.

Parameter adjustment bar.

This graphic shows the current setting for parameters such as display contrast and alarm volume in the Preferences menu.

WEEE (Waste Electrical and Electronic Equipment).

This symbol means that this product must not be disposed of with household waste. Observe local ordinances for proper disposal. See item 5 in Table 1-2.

Year of manufacture.

Manufacturer.

Authorized representative.

Audio paused (ALARM CONTROL key pressed once).

This symbol means the sounding of audible alarms is currently disabled. This period lasts 60 seconds. For more information, see section 3.5, Pausing the Audible Portion of Alarms.

Alarm paused (ALARM CONTROL key pressed twice).

This symbol means one or more alarms have been paused, or reset/canceled. The alarm is paused until the alarm condition is corrected and the condition reoccurs. For more information, see section 3.6, Pausing and Resetting Alarms.

Alarm off (Apnea off).

This symbol means that the Apnea alarm has been set to OFF in the Preferences menu. For more information, see section 3.6, Pausing and Resetting Alarms.

Exhalation valve detected.

This symbol means that an exhalation valve has been detected during ventilation.

No exhalation valve detected.

This symbol means that no exhalation valve has been detected during ventilation.

Single patient use only (ISO 7000-1051).

This symbol means that the labeled device is for use by a single patient only.

Freeze waveforms.

This symbol means the tracing of patient pressure and flow waveforms is currently paused or “frozen.”

Follow instructions for use (ISO 7000-1641).

This symbol directs the user to observe and adhere to the instructions contained in the product’s user manuals.

USB port.

This symbol indicates a communications port for interfacing with a USB connector. See item 11 in Figure 1-3.

Symbols and Markings

Table 1-1. Ventilator Symbols (Continued)

Symbols Descriptions

PC connection.

This symbol indicates a port that can be used by authorized Covidien product service personnel or Covidien service personnel for software maintenance. See item 10 in Figure 1-3.

Atmospheric pressure limitations. See section A.7 for specifications.

Humidity limitations. See section A.7 for specifications.

Temperature limitations. See section A.7 for specifications.

Fragile.

Keep dry.

Keep away from direct sunlight.

This side up.

Stacking limitation.

The number shown (represented by “n”) indicates the maximum number of additional identical packages that may be stacked on top of a package containing this device, when this device is correctly packaged.

For the Puritan Bennett™ 560 ventilator, n = 2.

Lithium battery.

This symbol Indicates that the contents of the package contain lithium batteries.

1.4 Labels (Identification and Instruction Information)

Various labels or specific markings are affixed to the ventilator that describe precautions to be taken for the correct use of the ventilator and contribute to the traceability of the product. See Table 1-2 and the figures on the following pages for illustrations of these labels and markings and their locations on the ventilator. Use the item numbers in Table 1-2 to locate the labels in Figures 1-1 through

1-4.

Table 1-2. Ventilator Labels and Markings

Labels (Identification and Instruction Information)

:Note:

The item number callouts in the following figures correspond to those listed in Table 1-2.

Figure 1-1. Locations of Labels—Top-Front View

Figure 1-2. Locations of Labels—Front-Left View

Figure 1-3. Location of Labels and Markings—Rear View

Figure 1-4. Location of Labels—Bottom View

2Ventilator Overview

2.1Indications for Use

The Puritan Bennett™ 560 Ventilator is indicated for the continuous or intermittent mechanical ventilatory support of patients weighing at least 11 lb (5 kg) who require mechanical ventilation. The ventilator is a restricted medical device intended for use by qualified, trained personnel under the direction of a doctor. It is essential to read, understand, and follow these instructions before using the Puritan Bennett™ 560 Ventilator.

2.1.1 Target Patients

Specifically, the ventilator is applicable for adult and pediatric patients who require the following general types of invasive or non-invasive ventilatory support, as prescribed by an attending doctor:

•Positive Pressure ventilation

•Assist/Control, SIMV, or CPAP modes of ventilation

•Breath types including Volume Control, Pressure Control, and Pressure Support

2.1.2Target Environments

The ventilator is suitable for use in institutional, home, and portable settings. It is not intended for use in Emergency Medical Service (EMS) such as an emergency transport.

The Puritan Bennett™ 560 Ventilator is suitable for use on commercial aircraft, per FAA requirements. See section A.11, Standards Compliance and IEC Classification. Patients traveling with the Puritan Bennett™ 560 Ventilator may be required by their airline to demonstrate evidence of compliance with the RTCA/DO-160F standard, as well as other requirements. Contact your airline prior to travel to determine airline specific requirements and documentation.

<WARNING:

Even though the Puritan Bennett™ 560 Ventilator meets current safety standards, the internal Lithium-ion battery of the device exceeds the 100Wh threshold and is therefore considered to be Dangerous Goods (DG) Class 9 – Miscellaneous, when transported in commerce. As such, the Puritan Bennett™ 560 Ventilator and/or the associated Lithium-ion battery are subject to strict transport conditions under the Dangerous Goods Regulation for air transport (IATA: International Air Transport

Association), International Maritime Dangerous Goods code for sea and the European Agreement concerning the International Carriage of Dangerous Goods by Road (ADR) for Europe. Private individuals who transport the device are excluded from these regulations although for air transport some requirements apply. For air transport; the Puritan Bennett™ 560 Ventilator is permitted as checked-in or carry-on baggage. Two spare batteries per person may be taken on board as carry-on luggage only, with the prior approval of the airline. This classification and regulatory requirements may vary depending upon the country and mode of transport. Therefore it is recommended that users verify with the carrier / airline as to which measures to take before the voyage.

2.1.3Target Operators

<WARNING:

This ventilator must be used only under the responsibility and on the prescription of a doctor.

The ventilator may be operated by the following caregivers:

•Respiratory therapists

•Doctors

•Nurses

•Homecare providers

•Patient and patient’s families

For more details on knowledge and skill requirements for operating the Puritan Bennett™ 560 ventilator, please consult your clinician.

It is the responsibility of the clinician or clinical educator to ensure that both the patient and the caregiver fully understand the topics necessary for operation of the ventilator.

2.2 Contraindications

This ventilator is not for use with anesthetic gases, and is not intended for use as an emergency transport ventilator.

Operational Use

2.3 Operational Use

The Puritan Bennett™ 560 ventilator uses a micro-turbine to provide ventilatory support to patients. Clinicians may use a variety of interfaces to connect patients to the ventilator for continuous or intermittent ventilatory support. Some examples include mouthpieces; nasal masks or full face masks; endotracheal tubes or tracheotomy tubes. User-selectable ventilation modes are:

•Assisted Controlled Volume (V A/C)

•Assisted Controlled Pressure (P A/C)

•Volume Synchronized Intermittent Mandatory Ventilation (V SIMV)

•Pressure Synchronized Intermittent Mandatory Ventilation (P SIMV)

•Continuous Positive Airway Pressure (CPAP)

•Pressure Support Ventilation with apnea ventilation (PSV/ST)

2.3.1Safety Net

Incorporated in the ventilator design is an alarm system that continuously monitors both patient and machine for signs of specific errors or faults that could lead to an unsafe condition. Should any of these errors or faults be detected, the alarm system announces the specific alarm condition both audibly and visually. The machine-related alarm conditions are factory set, whereas the patientrelated alarm conditions are defined by alarm-threshold values selected by an operator (a clinician or a caregiver). For more information, see Chapter 3, Alarms and Troubleshooting.

2.3.2 Settings

A software key, known as the Locking key, restricts access to ventilation parameter settings and ventilation mode changes in order to distinguish between clinician usage and patient usage.

2.3.3 Oxygen Enrichment

Oxygen may be supplied from an external, low pressure source, but the oxygen flow must be limited to 15 lpm (50 kPa, 500 mbar). The ventilator automatically compensates for the extra flow created by the external oxygen supply (see Chapter 4, Installation and Assembly.)

2.3.4 Breathing Circuit

The ventilator can be used with a singleor double-limb patient circuit. If exhaled volume monitoring is required (such as ventilator dependent patients), use the double-limb circuit for exhaled tidal volume monitoring. For more information, see section 4.4, Patient Circuit.

<WARNING:

Users must always possess an additional breathing circuit and exhalation valve while using the Puritan Bennett™ 560 ventilator.

2.4Device Classification

The ventilator’s IEC/EN 60601-1classification is as follows:

•Protection/insulation class (electric shock): Class II

•Protection index of enclosure: IP32

•Degree of protection against risk of electric shock: BF

•Power: External (AC–mains, or DC–cigarette lighter) or internal (DC–battery)

•Operation mode: Continuous operation

For additional information, see Appendix A, Specifications.

Front Panel

2.5 Front Panel

Figure 2-1. Front Panel

1.If exhaled tidal volume monitoring is required, use the double-limb circuit.

2.6 Back Panel

Figure 2-2. Back Panel

Control Panel

2.7 Control Panel

Figure 2-3. Control Panel

2.8 Ventilation Menu

Figure 2-4. Ventilation Menu Display (on standby at left; during ventilation at right)

Alarm Menu

2.9 Alarm Menu

Figure 2-5. Alarm Menu (on standby at left; during ventilation at right)

2.10 Waveforms Menu

The display of waveforms (see Figure 2-6) is optional and can be selected using the Menu key.

The Waveform menu is only accessible when ventilation is active.

Figure 2-6. Waveforms Menu