Danfoss control panel lcp 102 инструкция

Remote Mounting of LCP

®

VLT

HVAC Drive FC 102

Items Supplied

•

LCP cables with 2 M12 connectors (90° male connector and straight female connector). Cable lengths: 3 m, 5 m, and 10 m

(10 ft, 16 ft, 33 ft). See also Table 1.1.

•

Blind cover with M12 female connector.

•

Base plate with D-sub connector and M12 male connector.

•

Two gaskets and 1 nut for the D-sub connector.

•

Intermediate cover with the front cover.

•

Disassembly tool.

Length [m (ft)]

3 (10)

5 (16)

10 (33)

Table 1.1 Cable Ordering Numbers

More Items Required

•

Local control panel (LCP).

•

Four M4 self-tapping screws for mounting.

This instruction is valid for frequency converters that were ordered with the LCP. Front covers of frequency converters that

were ordered without LCPs do not have holes for mounting the blind covers.

Safety Instructions

For important information about safety precautions for installation, refer to the product-specific operating guide.

WARNING

DISCHARGE TIME

The frequency converter contains DC-link capacitors, which can remain charged even when the frequency converter is not

powered. High voltage can be present even when the warning LED indicator lights are off. Failure to wait the specified time

after power has been removed before performing service or repair work can result in death or serious injury.

•

Stop the motor.

•

Disconnect AC mains and remote DC-link power supplies, including battery back-ups, UPS, and DC-link connections to

other frequency converters.

•

Disconnect or lock PM motor.

•

Wait for the capacitors to discharge fully. The minimum duration of waiting time is specified in .

•

Before performing any service or repair work, use an appropriate voltage measuring device to make sure that the

capacitors are fully discharged.

Ordering number

134B5223

134B5224

134B5225

Danfoss A/S © 11/2017 All rights reserved.

MI05A202

User Interface

The display area is activated when the frequency converter

receives power from mains voltage, a DC bus terminal, or

an external 24 V DC supply.

The information displayed on the LCP can be customized

for user application.

•

Each display readout has a parameter associated

with it

•

Options are selected in the quick menu Q3-13

Display Settings

•

Display 2 has an alternate larger display option

•

The frequency converter status at the bottom line

of the display is generated automatically and is

not selectable

Status

0.0%

1.1

1.2

Off Remote Stop

2

Illustration 4.2 Display Readouts

Display

Parameter number

1.1

0-20

1.2

0-21

1.3

0-22

2

0-23

3

0-24

Table 4.1 Legend to Illustration 4.2

Phone: 800.894.0412 — Fax: 888.723.4773 — Web: www.ctiautomation.net — Email: info@ctiautomation.net

®

VLT

HVAC Drive Operating Instructions

1 (1)

0.00 A

0.00 kw

0.0Hz

2605kWh

3

1.3

Default setting

Reference %

Motor current

Power [kW]

Frequency

kWh counter

®

MG11AI02 — VLT

is a registered Danfoss trademark

4.1.3 Display Menu Keys

Menu keys are used for menu access for parameter set-up,

toggling through status display modes during normal

operation, and viewing fault log data.

Quick

Status

Menu

Illustration 4.3 Menu Keys

Key

Function

Status

Shows operational information.

•

In Auto mode, press to toggle between

status read-out displays

•

Press repeatedly to scroll through each

status display

•

Press [Status] plus [

display brightness

•

The symbol in the upper right corner of the

display shows the direction of motor

rotation and which set-up is active. This is

not programmable.

Quick Menu

Allows access to programming parameters for

initial set up instructions and many detailed

application instructions.

•

Press to access Q2 Quick Setup for

sequenced instructions to program the basic

frequency controller set up

•

Follow the sequence of parameters as

presented for the function set up

Main Menu

Allows access to all programming parameters.

•

Press twice to access top-level index

•

Press once to return to the last location

accessed

•

Press to enter a parameter number for

direct access to that parameter

Alarm Log

Displays a list of current warnings, the last 10

alarms, and the maintenance log.

•

For details about the frequency converter

before it entered the alarm mode, select the

alarm number using the navigation keys

and press [OK].

Table 4.2 Function Description Menu Keys

Main

Alarm

Menu

Log

▲

▼

] or [

] to adjust the

33

4

4