Магнитола пионер deh 1500ubg инструкция по применению

Manuals for DEH-1500UBG

Найти продукт

Раздел: Авто, мото оборудование и транспорт

Тип: Автомагнитола

Инструкция к Автомагнитоле Pioneer DEH-1500UBG

CD RDS RECEIVER

AUTORADIO CD RDS

SINTOLETTORE CD RDS

English NederlandsDeutschEspañolItalianoFrançais Русский

REPRODUCTOR DE CD CON RECEPTOR RDS

CD RDS-EMPFÄNGER

CD RDS-ONTVANGER

CD RDS ПРИЕМНИК

Owner’s Manual

Mode d’emploi

DEH-1500UB

Manuale d’istruzioni

Manual de instrucciones

DEH-1500UBG

Bedienungsanleitung

Handleiding

DEH-1500UBA

Руководство пользователя

DEH-1500UBB

Section

01

Before you start

Before you start

Thank you for purchasing this PIONEER

About this unit

In case of trouble

product

The tuner frequencies on this unit are allocated

Should this unit fail to operate properly, please

To ensure proper use, please read through this

for use in Western Europe, Asia, the Middle

contact your dealer or nearest authorized

manual before using this product. It is especially

East, Africa and Oceania. Use in other areas

PIONEER Service Station.

important that you read and observe WARN-

may result in poor reception. The RDS (radio

INGs and CAUTIONs in this manual. Please

data system) function only operates in areas

keep the manual in a safe and accessible place for

with broadcasting RDS signals for FM stations.

future reference.

CAUTION

This product is a class 1 laser product classi-

fied under the Safety of laser products, IEC

60825-1:2007.

If you want to dispose this product, do not

mix it with general household waste. There is

a separate collection system for used elec-

tronic products in accordance with legislation

that requires proper treatment, recovery and

CAUTION

recycling.

! Do not allow this unit to come into contact

with liquids. Electrical shock could result.

Private households in the member states of the

Also, damage to this unit, smoke, and over-

heating could result from contact with

EU, in Switzerland and Norway may return their

used electronic products free of charge to desig-

liquids.

nated collection facilities or to a retailer (if you

! The Pioneer CarStereo-Pass is for use only in

purchase a similar new one).

Germany.

For countries not mentioned above, please con-

! Always keep the volume low enough to hear

tact your local authorities for the correct method

outside sounds.

of disposal.

! Avoid exposure to moisture.

By doing so you will ensure that your disposed

! If the battery is disconnected or discharged,

product undergoes the necessary treatment, re-

any preset memory will be erased.

covery and recycling and thus prevent potential

Note

negative effects on the environment and human

Function setting operations are completed even

health.

if the menu is canceled before the operations

are confirmed.

About this manual

In the following instructions, USB memories

and USB audio players are collectively referred

to as “USB storage device”.

2

En

Head unit

c d

5

9

1 2 3 4 6 7

bae8

Section

Operating this unit

Operating this unit

02

Display indication

Indicator State

LANGUAGE (multi-language)

English

4 6 8

This unit can display the text information from a

! Tuner: band and fre-

21 3 75

compressed audio file even for information em-

quency

bedded in English or Russian.

! RDS: program service

! If the embedded language and the selected

name, PTY information

Main infor-

language setting are not the same, text infor-

and other literal informa-

9

mation sec-

mation may not display properly.

9

a

tion

tion

! Some characters may not be displayed prop-

! CD player and USB stor-

erly.

Indicator State

age device: elapsed play-

1 Turn M.C. to select the desired setting.

back time and text

Part Part

ENG (English)—РУС (Russian)

The list function is being oper-

information

1

(list)

2 Press M.C. to confirm the selection.

ated.

1 h (eject) 8

(equalizer)

Appears when a lower tier of

a

CLOCK SET (setting the clock)

Sub infor-

2 SRC/OFF 9 BAND

folder or menu exists.

2

mation sec-

Sub information is displayed.

1 Turn M.C. to adjust hour.

(back)/

tion

MULTI-CONTROL

2 Press M.C. to select minute.

3

a

DIMMER

(M.C.)

TA (traffic

Set up menu

3 Turn M.C. to adjust minute.

(dimmer)

3

announce-

TA function is on.

4 Press M.C. to confirm the selection.

When you turn the ignition switch to ON after in-

4

(list) b c/d

ments)

stallation, set up menu appears on the display.

FM STEP (FM tuning step)

5 DISP c 1/

to 6/

TP (traffic

You can set up the menu options below.

Normally, the FM tuning step employed by seek

program

AUX input jack

4

A TP station is tuned in.

tuning is 50 kHz. When AF or TA is on, the tuning

identifica-

1 After installation of this unit, turn the

6 Disc loading slot d

(3.5 mm stereo

step automatically changes to 100 kHz. It may be

tion)

ignition switch to ON.

jack)

preferable to set the tuning step to 50 kHz when

SET UP appears.

AF is on.

7 USB port e Detach button

The sound retriever function

5

(sound re-

! The tuning step remains at 50 kHz during man-

is on.

2 Turn M.C. to switch to YES.

triever)

ual tuning.

# If you do not operate for 30 seconds, the set up

CAUTION

1 Turn M.C. to select the FM tuning step.

6 LOC Local seek tuning is on.

menu will not be displayed.

! Use an optional Pioneer USB cable (CD-

50 (50 kHz)—100 (100 kHz)

# If you prefer not to set up at this time, turn M.C.

7

(repeat) Track or folder repeat is on.

U50E) to connect the USB storage device as

2 Press M.C. to confirm the selection.

to switch to NO. Press to select.

any device connected directly to the unit will

QUIT appears.

(ran-

If you select NO, you cannot set up in the set up

8

Random play is on.

protrude out from the unit, which could be

dom)

menu.

dangerous.

5 To finish your settings, turn M.C. to select

! Do not use unauthorized products.

3 Press M.C. to select.

YES.

# If you prefer to change your setting again, turn

4 Perform the following procedures to set

M.C. to switch to NO. Press to select.

the menu.

To proceed to the next menu option, you need to

6 Press M.C. to select.

confirm your selection.

En

3

Section

02

Operating this unit

Operating this unit

Notes

Removing the front panel to protect your unit from

Selecting a source

Tuner

! You can set up the menu options from the

theft

1 Press SRC/OFF to cycle between:

system menu. For details about the settings,

Basic operations

1 Press the detach button to release the front

TUNER (tuner)—CD (CD player)—USB (USB)

refer to System menu on page 7.

panel.

—AUX (AUX)

! You can cancel set up menu by pressing

Selecting a band

2 Push the front panel upward (M) and then pull

SRC/OFF.

Adjusting the volume

1 Press BAND until the desired band (FM1,

it toward (N) you.

1 Turn M.C. to adjust the volume.

FM2, FM3 for FM or MW/LW) is displayed.

Basic operations

Switching preset stations

1 Press c or d.

Important

CAUTION

! Select PCH (preset channel) under SEEK to

! Handle gently when removing or attaching

For safety reasons, park your vehicle when re-

use this function. For details about the set-

the front panel.

moving the front panel.

tings, refer to SEEK (left/right key setting) on

! Avoid subjecting the front panel to excessive

3 Always keep the detached front panel in a pro-

Note

the next page.

shock.

tection device such as a protection case.

When this unit’s blue/white lead is connected to

Manual tuning (step by step)

! Keep the front panel out of direct sunlight

Re-attaching the front panel

the vehicle’s auto-antenna relay control termi-

1 Press c or d.

and high temperatures.

1 Slide the front panel to the left.

nal, the vehicle’s antenna extends when this

! Select MAN (manual tuning) under SEEK to

! To avoid damaging the device or vehicle inte-

Make sure to insert the tabs on the left side of

unit’s source is turned on. To retract the anten-

use this function. For details about the set-

rior, remove any cables and devices attached

the head unit into the slots on the front panel.

na, turn the source off.

tings, refer to SEEK (left/right key setting) on

to the front panel before detaching it.

the next page.

Frequently used menu

Seeking

1 Press and hold c or d, and then release.

operations

You can cancel seek tuning by briefly pressing

c or d.

Returning to the previous display

While pressing and holding c or d, you can

Returning to the previous list (the folder one level

skip stations. Seek tuning starts as soon as

2 Press the right side of the front panel until it is

higher)

you release c or d.

firmly seated.

1 Press

/DIMMER.

If you cannot attach the front panel to the

Note

head unit successfully, make sure that you are

Returning to the ordinary display

This unit’s AF (alternative frequencies search)

placing the front panel onto the head unit cor-

Canceling the main menu

function can be turned on and off. AF should be

rectly. Forcing the front panel into place may

1 Press BAND.

off for normal tuning operation (refer to AF (al-

result in damage to the front panel or head

Returning to the ordinary display from the list

ternative frequencies search) on the next page).

unit.

1 Press BAND.

Turning the unit on

Storing and recalling stations

1 Press SRC/OFF to turn the unit on.

for each band

Turning the unit off

Using preset tuning buttons

1 Press and hold SRC/OFF until the unit turns

off.

1 When you find a station that you want

to store in memory, press one of the preset

tuning buttons (1/

to 6/ ) and hold until

the preset number stops flashing.

4

En

Section

Operating this unit

Operating this unit

02

2 Press one of the preset tuning buttons

Searching for an RDS station by PTY information

OTHERS (others)

Local seek tuning lets you tune in to only those

(1/

to 6/ ) to select the desired station.

English

You can search for general types of broadcasting

radio stations with sufficiently strong signals for

EDUCATE (Education), DRAMA (Drama), CUL-

programs, such as those listed in the following

good reception.

Switching the display

TURE (Culture), SCIENCE (Science), VARIED (Var-

section. Refer to this page.

1 Press M.C. to select the desired setting.

ied), CHILDREN (Children’s), SOCIAL (Social

1 Press

(list).

FM: OFF—LV1—LV2—LV3—LV4

affairs), RELIGION (Religion), PHONE IN (Phone

Selecting the desired text information

2 Turn M.C. to select a program type.

MW/LW: OFF—LV1 —LV2

in), TOURING (Travel), LEISURE (Leisure), DOCU-

1 Press DISP to cycle between the following:

NEWS/INFO—POPULAR—CLASSICS—

The highest level setting allows reception of

MENT (Documentaries)

! FREQUENCY (program service name or

OTHERS

only the strongest stations, while lower levels

frequency)

3 Press M.C. to begin the search.

allow the reception of weaker stations.

! BRDCST INFO (program service name/PTY

The unit searches for a station broadcasting

Function settings

TA (traffic announcement standby)

information)

that type of program. When a station is found,

! CLOCK (source name and clock)

1 Press M.C. to display the main menu.

its program service name is displayed.

1 Press M.C. to turn traffic announcement

! To cancel the search, press M.C. again.

Notes

standby on or off.

2 Turn M.C. to change the menu option

! The program of some stations may differ

! If the program service name cannot be ac-

and press to select FUNCTION.

from that indicated by the transmitted PTY.

AF (alternative frequencies search)

quired in FREQUENCY, the broadcast fre-

! If no station is broadcasting the type of

quency is displayed instead. If the program

3 Turn M.C. to select the function.

program you searched for, NOT FOUND is

1 Press M.C. to turn AF on or off.

service name is detected, the program serv-

Once selected, the following functions can be

displayed for about two seconds and then

NEWS (news program interruption)

ice name will be displayed.

adjusted.

the tuner returns to the original station.

! BRDCST INFO text information will change

# If MW/LW band is selected, only BSM, LOCAL

1 Press M.C. to turn the NEWS function on or

automatically.

and SEEK are available.

off.

! Depending on the band, text information can

PTY list

be changed.

BSM (best stations memory)

SEEK (left/right key setting)

! Text information items that can be changed

NEWS/INFO (news and information)

BSM (best stations memory) automatically stores

You can assign a function to the left and right keys

depend on the area.

NEWS (News), AFFAIRS (Current affairs), INFO

the six strongest stations in the order of their sig-

of the unit.

(Information), SPORT (Sports), WEATHER (Weath-

nal strength.

Select MAN (manual tuning) to tune up or down

Using PTY functions

er), FINANCE (Finance)

1 Press M.C. to turn BSM on.

manually or select PCH (preset channel) to switch

You can tune in to a station using PTY (program

To cancel, press M.C. again.

between preset channels.

type) information.

POPULAR (popular)

1 Press M.C. to select MAN or PCH.

REGION (regional)

POP MUS (Popular music), ROCK MUS (Rock

music), EASY MUS (Easy listening), OTH MUS

When AF is used, the regional function limits the

(Other music), JAZZ (Jazz), COUNTRY (Country

selection of stations to those broadcasting region-

CD/CD-R/CD-RW and USB

music), NAT MUS (National music), OLDIES

al programs.

storage devices

(Oldies music), FOLK MUS (Folk music)

1 Press M.C. to turn the regional function on or

off.

Basic operations

CLASSICS (classics)

LOCAL (local seek tuning)

L. CLASS (Light classical), CLASSIC (Classical)

Playing a CD/CD-R/CD-RW

1 Insert the disc into the disc loading slot with

the label side up.

Ejecting a CD/CD-R/CD-RW

1 Press h.

En

5

Section

02

Operating this unit

Operating this unit

Switching the display

2 Use M.C. to select the desired file name

Playing songs on a USB storage device

Pausing playback

(or folder name).

1 Open the USB port cover.

1 Press 4/PAUSE to pause or resume.

2 Plug in the USB storage device using a USB

Selecting the desired text information

Selecting a file or folder

Enhancing compressed audio and restoring rich

cable.

1 Press DISP to cycle between the following:

CD-DA

1 Turn M.C.

sound (sound retriever)

Playback is performed automatically.

1 Press 3/S.Rtrv to cycle between:

! ELAPSED TIME (track number and play-

Playing

Stopping playback of files on a USB storage de-

1—2—OFF (off)

back time)

1 When a file or track is selected, press M.C.

vice

1 is effective for low compression rates, and 2

! CLOCK (source name and clock)

1 You may disconnect the USB storage device at

is effective for high compression rates.

! SPEANA (spectrum analyzer)

Viewing a list of the files (or folders) in the se-

any time.

CD-TEXT

lected folder

The unit stops playback.

! TRACK INFO (track title/track artist/disc

1 When a folder is selected, press M.C.

Function settings

Selecting a folder

title)

Playing a song in the selected folder

1 Press 1/

! ELAPSED TIME (track number and play-

1 Press M.C. to display the main menu.

or 2/ .

1 When a folder is selected, press and hold M.C.

back time)

Selecting a track

! CLOCK (source name and clock)

2 Turn M.C. to change the menu option

1 Press c or d.

! SPEANA (spectrum analyzer)

Operations using special buttons

and press to select FUNCTION.

Fast forwarding or reversing

MP3/WMA/WAV

Once selected, the function below can be ad-

1 Press and hold c or d.

! TRACK INFO (track title/artist name/album

Selecting a repeat play range

justed.

! When playing compressed audio, there is no

title)

1 Press 6/

to cycle between the following:

sound during fast forward or reverse.

! FILE INFO (file name/folder name)

CD/CD-R/CD-RW

S.RTRV (sound retriever)

! ELAPSED TIME (track number and play-

! ALL – Repeat all tracks

Returning to root folder

Automatically enhances compressed audio and

back time)

! ONE – Repeat the current track

1 Press and hold BAND.

restores rich sound.

! CLOCK (source name and clock)

! FLD – Repeat the current folder

1 Press M.C. to select the desired setting.

Switching between compressed audio and CD-DA

! SPEANA (spectrum analyzer)

USB storage device

For details, refer to Enhancing compressed

1 Press BAND.

! ALL – Repeat all files

Notes

audio and restoring rich sound (sound retriever)

! ONE – Repeat the current file

Switching between playback memory devices

on this page.

! TRACK INFO and FILE INFO text information

! FLD – Repeat the current folder

You can switch between playback memory devices

will change automatically.

on USB storage devices with more than one Mass

! Depending on the version of iTunes used to

Playing tracks in random order

Storage Device-compatible memory device.

write MP3 files to a disc or media file types,

1 Press 5/

to turn random play on or off.

Audio adjustments

1 Press BAND.

incompatible text stored within an audio file

Tracks in a selected repeat range are played in

! You can switch between up to 32 different

random order.

1 Press M.C. to display the main menu.

may be displayed incorrectly.

memory devices.

! To change songs during random play, press d

! Text information items that can be changed

2 Turn M.C. to change the menu option

depend on the media.

to switch to the next track. Pressing c restarts

Note

playback of the current track from the begin-

and press to select AUDIO.

Disconnect USB storage devices from the unit

ning of the song.

Selecting and playing files/

when not in use.

3 Turn M.C. to select the audio function.

tracks from the name list

Once selected, the following audio functions

can be adjusted.

1 Press to switch to the file/track name

! FADER is not available when SUB.W/SUB.W

list mode.

is selected in SP-P/O MODE. For details, refer

to SP-P/O MODE (rear output and preout set-

ting) on page 8.

6

En

Section

Operating this unit

Operating this unit

02

! SUB.W, SUB.W CTRL and HPF SETTING are

Only frequencies lower than those in the selected

SLA (source level adjustment)

not available when REAR/REAR is selected in

1 Press M.C. to display the setting mode.

English

range are outputted from the subwoofer.

SP-P/O MODE. For details, refer to

2 Turn M.C. to select the equalizer.

SLA (Source level adjustment) lets you adjust the

1 Press M.C. to display the setting mode.

SP-P/O MODE (rear output and preout set-

POWERFUL—NATURAL—VOCAL—CUS-

volume level of each source to prevent radical

2 Press M.C. to cycle between the following:

ting) on the next page.

TOM1—CUSTOM2—FLAT—SUPER BASS

changes in volume when switching between sour-

Cut-off frequency—Output level—Slope level

! SUB.W CTRL and HPF SETTING are not avail-

The equalizer band and equalizer level can be

ces.

Rates that can be adjusted will flash.

able when SUB.W is selected in OFF. For de-

customized when CUSTOM1 or CUSTOM2 is

! Settings are based on the FM volume level,

3 Turn M.C. to select the desired setting.

tails, refer to SUB.W (subwoofer on/off

selected.

which remains unchanged.

Cut-off frequency: 50HZ—63HZ—80HZ—

setting) on this page.

If selecting CUSTOM1 or CUSTOM2, complete

! The MW/LW volume level can also be adjusted

100HZ—125HZ—160HZ—200HZ

the procedures outlined below. If selecting

with this function.

Output level: –24 to +6

FADER (fader adjustment)

other options, press M.C. to return to the pre-

! When selecting FM as the source, you cannot

Slope level: –6 — –12

vious display.

switch to SLA.

1 Press M.C. to display the setting mode.

! CUSTOM1 can be set separately for each

BASS BOOST (bass boost)

1 Press M.C. to display the setting mode.

2 Turn M.C. to adjust the front/rear speaker bal-

source.

2 Turn M.C. to adjust the source volume.

ance.

! CUSTOM2 is a shared setting used in com-

1 Press M.C. to display the setting mode.

Adjustment range: +4 to –4

mon for all sources.

2 Turn M.C. to select a desired level.

BALANCE (balance adjustment)

3 Press M.C. to display the setting mode.

0 to +6 is displayed as the level is increased or

4 Press M.C. to cycle between the following:

decreased.

1 Press M.C. to display the setting mode.

System menu

Equalizer band—Equalizer level

2 Turn M.C. to adjust the left/right speaker bal-

HPF SETTING (high pass filter adjustment)

5 Turn M.C. to select the desired setting.

Important

ance.

Equalizer band: 80HZ—250HZ—800HZ—

When you do not want low sounds from the sub-

PW SAVE (power saving) is canceled if the ve-

EQ SETTING (equalizer recall)

2.5KHZ—8KHZ

woofer output frequency range to play from the

hicle battery is disconnected and will need to be

Equalizer level: +6 to –6

front or rear speakers, turn on the HPF (high pass

turned back on once the battery is reconnected.

! You can also switch the equalizer by pressing

filter). Only frequencies higher than those in the

When PW SAVE (power saving) is off, depend-

repeatedly.

selected range are output from the front or rear

ing on connection methods, the unit may con-

speakers.

tinue to draw power from the battery if your

LOUDNESS (loudness)

1 Press M.C. to display the setting mode.

vehicle’s ignition doesn’t have an ACC (acces-

Loudness compensates for deficiencies in the low-

2 Press M.C. to cycle between the following:

sory) position.

frequency and high-frequency ranges at low vol-

Cut-off frequency—Slope level

ume.

3 Turn M.C. to select the desired setting.

1 Press M.C. to display the main menu.

1 Press M.C. to select the desired setting.

Cut-off frequency: OFF—50HZ—63HZ—80HZ

OFF (off)—LOW (low)—MID (mid)—HI (high)

—100HZ—125HZ—160HZ—200HZ

2 Turn M.C. to change the menu option

Slope level: –6 — –12

and press to select SYSTEM.

SUB.W (subwoofer on/off setting)

This unit is equipped with a subwoofer output

3 Turn M.C. to select the system menu

which can be turned on or off.

function.

1 Press M.C. to select the desired setting.

Once selected, the following system menu func-

NOR (normal phase)—REV (reverse phase)—

tions can be adjusted.

OFF (subwoofer off)

! MUTE MODE and PW SAVE are not available

for DEH-1500UBA.

SUB.W CTRL (subwoofer adjustment)

En

7

Section

02

Operating this unit

Operating this unit

3 Turn M.C. to change the menu option

LANGUAGE (multi-language)

Sound from this system is automatically muted or

SP-P/O MODE (rear output and preout setting)

and press to select INITIAL.

attenuated when a signal from equipment with a

This unit can display the text information from a

The rear speaker leads output and the RCA output

mute function is received.

compressed audio file even for information em-

4 Turn M.C. to select the initial menu func-

of this unit can be used to connect a full-range

1 Press M.C. to display the setting mode.

bedded in English or Russian.

tion.

speaker or subwoofer. Select a suitable option for

2 Turn M.C. to select the desired setting.

! If the embedded language and the selected

Once selected, the following initial menu func-

your connection.

You can select any one of the options in the fol-

language setting are not the same, text infor-

tions can be adjusted.

1 Press M.C. to display the setting mode.

lowing list:

mation may not display properly.

2 Turn M.C. to select the desired setting.

! MUTE – Muting

! Some characters may not be displayed prop-

FM STEP (FM tuning step)

You can select any one of the options in the fol-

! 20dB ATT – Attenuation (20dB ATT has a

erly.

lowing list:

stronger effect than 10dB ATT)

Normally, the FM tuning step employed by seek

1 Turn M.C. to select the desired setting.

! REAR/SUB.W – Select when there is a full-

! 10dB ATT – Attenuation

tuning is 50 kHz. When AF or TA is on, the tuning

ENG (English)—РУС (Russian)

range speaker connected to the rear speak-

step automatically changes to 100 kHz. It may be

PW SAVE (power saving)

er leads output and there is a subwoofer

CLOCK SET (setting the clock)

preferable to set the tuning step to 50 kHz when

connected to the RCA output.

Switching this function on enables you to reduce

AF is on.

! SUB.W/SUB.W – Select when there is a

1 Press M.C. to display the setting mode.

the consumption of battery power.

! The tuning step remains at 50 kHz during man-

subwoofer connected directly to the rear

2 Press M.C. to select the segment of the clock

! Turning on the source is the only operation al-

ual tuning.

speaker leads output without any auxiliary

display you wish to set.

lowed when this function is on.

1 Press M.C. to select the FM tuning step.

amp and there is a subwoofer connected

Hour—Minute

1 Press M.C. to turn the power save on or off.

50 (50 kHz)—100 (100 kHz)

to the RCA output.

3 Turn M.C. to adjust the clock.

! REAR/REAR – Select when there is a full-

12H/24H (time notation)

range speaker connected to the rear speak-

Switching the dimmer setting

er leads output and the RCA output.

1 Press M.C. to select the desired setting.

If there is a full-range speaker connected to

You can adjust the brightness of illumination.

12H (12-hour clock)—24H (24-hour clock)

the rear speaker leads output and the RCA

output is not used, you may select either

AUTO PI (auto PI seek)

1 Press M.C. to display the main menu.

REAR/SUB.W or REAR/REAR.

The unit can automatically search for a different

2 Turn M.C. to display ILLUMI and press to

station with the same programming, even during

select.

preset recall.

System menu

1 Press M.C. to turn Auto PI seek on or off.

3 Press M.C. to select the desired setting.

1 Press and hold SRC/OFF until the unit

AUX (auxiliary input)

OFF (off)—ON (on)

turns off.

! You can also change the dimmer setting by

Activate this setting when using an auxiliary de-

pressing and holding

/DIMMER.

vice connected to this unit.

2 Press and hold SRC/OFF until the main

1 Press M.C. to turn AUX on or off.

menu appears in the display.

MUTE MODE (mute mode)

Initial menu

3 Turn M.C. to change the menu option

1 Press and hold SRC/OFF until the unit

and press to select SYSTEM.

turns off.

4 Turn M.C. to select the system menu

2 Press and hold SRC/OFF until the main

function.

menu appears in the display.

Once selected, the following system menu func-

tions can be adjusted.

8

En

For details, refer to System menu on page 7.

— Never wire the negative speaker cable directly

Connections

to ground.

Important

— Never band together negative cables of multi-

Using an AUX source

! When installing this unit in a vehicle without

ple speakers.

an ACC (accessory) position on the ignition

! When this unit is on, control signals are sent

1 Insert the stereo mini plug into the AUX

switch, failure to connect the red cable to the

through the blue/white cable. Connect this

input jack.

terminal that detects operation of the ignition

cable to the system remote control of an ex-

key may result in battery drain.

ternal power amp or the vehicle’s auto-anten-

2 Press SRC/OFF to select AUX as the

na relay control terminal (max. 300 mA

source.

F

F

O

N

12 V DC). If the vehicle is equipped with a

O

T

S

Note

A

glass antenna, connect it to the antenna

T

R

AUX cannot be selected unless the auxiliary set-

booster power supply terminal.

ting is turned on. For more details, refer to AUX

! Never connect the blue/white cable to the

ACC position No ACC position

(auxiliary input) on the previous page.

power terminal of an external power amp.

! Use of this unit in conditions other than the

Also, never connect it to the power terminal

following could result in fire or malfunction.

of the auto antenna. Doing so may result in

Switching the display

— Vehicles with a 12-volt battery and negative

battery drain or a malfunction.

grounding.

! The black cable is ground. Ground cables for

Selecting the desired text information

— Speakers with 50 W (output value) and 4 W to

this unit and other equipment (especially,

1 Press DISP to cycle between the following:

8 W (impedance value).

high-current products such as power amps)

! Source name

! To prevent a short-circuit, overheating or mal-

must be wired separately. If they are not, an

! Source name and clock

function, be sure to follow the directions

accidental detachment may result in a fire or

below.

malfunction.

— Disconnect the negative terminal of the bat-

If an unwanted display appears

tery before installation.

This unit

— Secure the wiring with cable clamps or adhe-

Turn off the unwanted display using the proce-

sive tape. Wrap adhesive tape around wiring

dures listed below.

that comes into contact with metal parts to

protect the wiring.

1 Press M.C. to display the main menu.

— Place all cables away from moving parts,

such as the shift lever and seat rails.

2 Turn M.C. to change the menu option

— Place all cables away from hot places, such

and press to select SYSTEM.

as near the heater outlet.

— Do not connect the yellow cable to the battery

3 Turn M.C. to display DEMO OFF and press

by passing it through the hole to the engine

to select.

compartment.

— Cover any disconnected cable connectors

4 Turn M.C. to switch to YES.

with insulating tape.

— Do not shorten any cables.

5 Press M.C. to select.

— Never cut the insulation of the power cable of

this unit in order to share the power with

other devices. The current capacity of the

cable is limited.

— Use a fuse of the rating prescribed.

3 45

Section

Operating this unit

Installation

02

03

English

21

1 Power cord input

2 Rear output or subwoofer output

3 Antenna input

4 Fuse (10 A)

5 Wired remote input (DEH-1500UBG, DEH-

1500UBB and DEH-1500UB only)

Hard-wired remote control adapter can be

connected (sold separately).

En

9

Power cord

3

4

1

2

5

6

3

4

7

5

6

8

a

9

b

e

d

9 Blue/white

Power amp (sold separately)

! When installing, to ensure proper heat dis-

The pin position of the ISO connector will dif-

persal when using this unit, make sure you

Perform these connections when using the op-

fer depending on the type of vehicle. Connect

leave ample space behind the rear panel and

tional amplifier.

9 and b when Pin 5 is an antenna control

wrap any loose cables so they are not block-

type. In another type of vehicle, never con-

3

ing the vents.

1

nect 9 and b.

2

a Blue/white

4





Connect to system control terminal of the

55





power amp (max. 300 mA 12 V DC).

b Blue/white

1 System remote control

Connect to auto-antenna relay control termi-

Connect to Blue/white cable.

nal (max. 300 mA 12 V DC).

2 Power amp (sold separately)

c Yellow/black (DEH-1500UBG, DEH-1500UBB

3 Connect with RCA cables (sold separately)

and DEH-1500UB only)

4 To Rear output or subwoofer output

If you use an equipment with Mute function,

5 Rear speaker or subwoofer

wire this lead to the Audio Mute lead on that

equipment. If not, keep the Audio Mute lead

free of any connections.

c

Installation

d Speaker leads

Important

White: Front left +

White/black: Front left *

! Check all connections and systems before

1 To power cord input

Gray: Front right +

final installation.

2 Depending on the kind of vehicle, the func-

Gray/black: Front right *

! Do not use unauthorized parts as this may

tion of 3 and 5 may be different. In this

Green: Rear left + or subwoofer +

cause malfunctions.

case, be sure to connect 4 to 5 and 6 to

Green/black: Rear left * or subwoofer *

! Consult your dealer if installation requires

3.

Violet: Rear right + or subwoofer +

drilling of holes or other modifications to the

3 Yellow

Violet/black: Rear right * or subwoofer *

vehicle.

Back-up (or accessory)

e ISO connector

! Do not install this unit where:

4 Yellow

In some vehicles, the ISO connector may be

— it may interfere with operation of the vehicle.

Connect to the constant 12 V supply termi-

divided into two. In this case, be sure to con-

— it may cause injury to a passenger as a result

nal.

nect to both connectors.

of a sudden stop.

5 Red

! The semiconductor laser will be damaged if

Notes

Accessory (or back-up)

it overheats. Install this unit away from hot

! Change the initial menu of this unit. Refer to

6 Red

places such as near the heater outlet.

SP-P/O MODE (rear output and preout set-

Connect to terminal controlled by ignition

! Optimum performance is obtained when the

ting) on page 8.

switch (12 V DC).

unit is installed at an angle of less than 60°.

The subwoofer output of this unit is monau-

7 Connect leads of the same color to each

ral.

other.

60°

! When using a subwoofer of 70 W (2 W), be

8 Black (chassis ground)

sure to connect the subwoofer to the violet

and violet/black leads of this unit. Do not

connect anything to the green and green/

black leads.

5cmcm

Section

03

Installation

Installation

Leave ample

5 cm

space

5 cm

DIN front/rear mount

This unit can be properly installed using either

front-mount or rear-mount installation.

Use commercially available parts when instal-

ling.

DIN Front-mount

1 Insert the mounting sleeve into the dash-

board.

For installation in shallow spaces, use the sup-

plied mounting sleeve. If there is enough space,

use the mounting sleeve that came with the ve-

hicle.

2 Secure the mounting sleeve by using a

screwdriver to bend the metal tabs (90°) into

place.

1

2

1 Dashboard

10

En

Section

Installation

Additional information

03

2 Mounting sleeve

! When reattaching the trim ring, point the

Troubleshooting

Error messages

# Make sure that the unit is installed securely in

side with the notched tab down.

English

place. An unstable installation may cause skipping

When you contact your dealer or your nearest

or other malfunctions.

2 Insert the supplied extraction keys into

Symptom Cause Action

Pioneer Service Center, be sure to note the error

both sides of the unit until they click into

message.

The display

You did not per-

Perform operation

place.

DIN Rear-mount

automatically

form any opera-

again.

Common

returns to the

tion within

1 Determine the appropriate position

3 Pull the unit out of the dashboard.

ordinary dis-

about 30 sec-

where the holes on the bracket and the side

Message Cause Action

play.

onds.

of the unit match.

AMP ERROR Unit fails to op-

Check the speak-

The repeat

Depending on

Select the repeat

erate or speaker

er connection. If

play range

the repeat play

play range again.

connection is

the message fails

changes un-

range, the se-

incorrect; pro-

to disappear even

expectedly.

lected range

tective circuit is

after the engine is

may change

activated.

switched off/on,

when another

contact your deal-

2 Tighten two screws on each side.

Removing and re-attaching the front

folder or track is

er or an author-

panel

being selected

ized Pioneer

or during fast

You can remove the front panel to protect your

Service Station

3

1

forwarding/re-

unit from theft.

for assistance.

versing.

Press the detach button and push the front

panel upward and pull it toward you.

A subfolder is

Subfolders can-

Select another re-

2

For details, refer to Removing the front panel to

not played

not be played

peat play range.

CD player

protect your unit from theft and Re-attaching the

back.

when FLD (fold-

Message Cause Action

1 Tapping screw (5 mm × 8 mm)

front panel on page 4.

er repeat) is se-

2 Mounting bracket

lected.

ERROR-07,

The disc is dirty. Clean the disc.

3 Dashboard or console

NO XXXX ap-

There is no em-

Switch the display

11, 12, 17, 30

The disc is

Replace the disc.

pears when a

bedded text in-

or play another

scratched.

Removing the unit

display is

formation.

track/file.

ERROR-07,

There is an elec-

Turn the ignition

changed (NO

1 Remove the trim ring.

10, 11, 12,

trical or me-

switch OFF and

TITLE, for ex-

15, 17, 30,

chanical error.

back ON, or

ample).

A0

switch to a differ-

The unit is

You are using a

Move electrical

ent source, then

malfunction-

device, such as

devices that may

back to the CD

ing.

a cellular

be causing the in-

player.

There is inter-

phone, that

terference away

ERROR-15 The inserted

Replace the disc.

ference.

transmits elec-

from the unit.

disc is blank.

tric waves near

1 Trim ring

the unit.

ERROR-23 Unsupported

Replace the disc.

2 Notched tab

CD format.

! Releasing the front panel allows easier ac-

cess to the trim ring.

En

11

Appendix

Additional information

Additional information

Message Cause Action

Message Cause Action

Message Cause Action

Use only conventional, fully circular discs. Do not

use shaped discs.

FORMAT

Sometimes

Wait until the

SKIPPED The connected

Play an audio file

ERROR-19 Communication

Perform one of

READ

there is a delay

message disap-

USB storage de-

not embedded

failed.

the following op-

between the

pears and you

vice contains

with Windows

erations.

start of playback

hear sound.

files embedded

Media DRM 9/10.

–Turn the ignition

and when you

with Windows

switch OFF and

Do not insert anything other than a CD into the

start to hear any

Mediaä DRM 9/

back ON.

CD loading slot.

sound.

10.

–Disconnect the

USB storage de-

Do not use cracked, chipped, warped, or other-

NO AUDIO The inserted

Replace the disc.

PROTECT All the files in

Transfer audio

vice.

wise damaged discs as they may damage the play-

disc does not

the USB storage

files not em-

–Change to a dif-

er.

contain any

device are em-

bedded with

ferent source.

playable files.

bedded with

Windows Media

Unfinalized CD-R/RW discs cannot be played

Then, return to

Windows Media

DRM 9/10 to the

back.

SKIPPED The inserted

Replace the disc.

the USB source.

DRM 9/10.

USB storage de-

disc contains

Do not touch the recorded surface of the discs.

vice and connect.

ERROR-23 USB storage de-

USB storage de-

DRM protected

vice was not for-

vice should be for-

Store discs in their cases when not in use.

files.

N/A USB The USB device

! Connect a USB

matted with

matted with

connected to is

Mass Storage

PROTECT All the files on

Replace the disc.

Do not attach labels, write on or apply chemicals

FAT12, FAT16 or

FAT12, FAT16 or

not supported

Class compliant

the inserted

to the surface of the discs.

FAT32.

FAT32.

by this unit.

device.

disc are em-

To clean a CD, wipe the disc with a soft cloth out-

! Disconnect

STOP There are no

Select a list that

bedded with

ward from the center.

your device and

songs in the

contains songs.

DRM.

replace it with a

current list.

Condensation may temporarily impair the player’s

compatible USB

performance. Let it rest for about one hour to ad-

USB storage device

storage device.

just to a warmer temperature. Also, wipe any

CHECK USB The USB con-

Check that the

Handling guidelines

damp discs off with a soft cloth.

Message Cause Action

nector or USB

USB connector or

Discs and player

Playback of discs may not be possible because of

FORMAT

Sometimes

Wait until the

cable has short-

USB cable is not

disc characteristics, disc format, recorded applica-

READ

there is a delay

message disap-

circuited.

caught in some-

Use only discs that feature either of the following

tion, playback environment, storage conditions,

between the

pears and you

thing or dam-

two logos.

and so on.

start of playback

hear sound.

aged.

and when you

Road shocks may interrupt disc playback.

The connected

Disconnect the

start to hear any

USB storage de-

USB storage de-

Read the precautions for discs before using them.

sound.

vice consumes

vice and do not

NO AUDIO There are no

Transfer the audio

more than maxi-

use it. Turn the

songs.

files to the USB

mum allowable

ignition switch to

storage device

current.

OFF, then to ACC

and connect.

or ON and then

The connected

Follow the USB

connect only

Use 12-cm discs. Do not use 8-cm discs or an

adapter for 8-cm discs.

USB storage de-

storage device in-

compliant USB

vice has secur-

structions to dis-

storage devices.

ity enabled.

able the security.

12

En