- Manuals
- Brands
- Nice Manuals
- Control Unit
- DPRO924
- Instructions and warnings for installation and use
-
Contents
-
Table of Contents
-
Bookmarks
Quick Links
Nice
DPRO924
Control unit
EN — Instructions and warnings for installation and use
Related Manuals for Nice DPRO924
Summary of Contents for Nice DPRO924
-
Page 1
Nice DPRO924 Control unit EN — Instructions and warnings for installation and use… -
Page 3
OXI/SMXI OXI New Generetion FUSE FUSE… -
Page 4: Table Of Contents
ENGLISH original operating instructions in Italian Contents Pictures …………………..I-II GENERAL WARNINGS: SAFETY — INSTALLATION — USE ……1 1 — PRODUCT DESCRIPTION AND INTENDED USE ……..2 2 — INSTALLATION ………………2 2.1 — Pre-installation checks …………….2 2.2 — Product application limits ……………2 2.3 — Typical system ………………2 2.4 — Control unit installation …………….2 3 — ELECTRICAL CONNECTIONS …………..3…
-
Page 5: General Warnings: Safety — Installation — Use
This product has been subjected to electromagnetic compatibility tests in the most critical situations of use and in the configurations specified in this instruction manual and in combination with the items in the Nice S.p.a. product catalogue. If the product is used in unspecified configurations or with other unspecified products, the electromagnetic compatibility may not be guar- anteed;…
-
Page 6: Product Description And Intended Use
5.1.3; in this case, at least one pair of photocells must be installed as shown in Fig. 2. PRODUCT DESCRIPTION AND INTENDED USE DPRO924 is a control unit to be used to automate sectional balanced doors. It can control motors with an encoder or Hall effect position control system or using electromechanical limit switches.
-
Page 7: Electrical Connections
Input for the connection of the Oview programmer, with the appropriate IBT4N adapter. CAUTION! — Disconnect the power before connecting/disconnecting the programmer. Input for the connection of the radio receiver aerial (note: in Nice flashers Mod. ELDC, the aerial is built-in) Aerial STOP Input for the connection of resistive-type sensitive edges (8k2) or optical ones (OSE), as described below (fig.
-
Page 8: Control Unit Electrical Connections
For more information, please contact the Nice Customer Service. 3.2 — Collegamenti elettrici della centrale di comando (fig. 5) CAUTION! –…
-
Page 9: Connecting A Radio Receiver
TABLE 2 Command No. 3 Open Command No. 4 Close SMXI, SMXIS Receiver in “Mode 1 or 2” Command No. 5 Stop output description Command No. 6 Step-by-Step Condominium Output No. 1 Step-by-Step Command No. 7 Step-by-Step High priority Output No. 2 Partial open;…
-
Page 10: Programming
3 seconds) Important — Unlocking with Nice SUMO motor: when the SUMO mo- tor is unlocked, if the DPRO924 control unit is on, it stores the command. To synchronize the encoder position again, closing as far as the maximum closing position must be performed.
-
Page 11: Operating Modes
‘hold-to-run’ mode, until synchronization of the encoder position is completed. 4.5 — Operating modes To perform this procedure, follow the following instructions: CAUTION! — If the functions of Table 3 are programmed with the Oview programming unit, it is necessary to set the dip switches to OFF. Select the type of motor, setting dip switches B-2 and B-3 to OFF TABLE 3: DIP SWITCH A…
-
Page 12: Modifying The Speed Value
4.5.3 — Modifying the speed value Set dip switch 2-B to OFF = It is possible to modify the opening, opening slowdown, closing and closing the OK led flashes regularly with slowdown speed using the Oview accessory or the board keys. green light.
-
Page 13: Further Details
FURTHER DETAILS 6.1 — Connecting photocells and accessories in standby mode The “Total stand by” function is used to reduce consumption and is useful when there is a buffer battery because it allows prolonging the battery charge, it can be activated using the Oview programmer. Once the “Stand by Time”…
-
Page 14: Connecting A Buffer Battery
6.3 — Connecting a buffer battery The control unit is prepared for the installation of the buffer bat- tery mod. PS224 (optional accessory): 7.2 Ah with built-in battery charger. To connect the buffer battery, proceed as shown on the side. CAUTION! — The electrical connection of the buffer battery to the control unit must be done only after completing all the installation and programming phases, since the battery is an…
-
Page 15: Product Disposal
7.2 — Diagnostics Some devices are supposed to issue warnings that allow identifying their status or any faults. Table 6 describes the various messages with their relative causes and solutions; the warnings are based on combinations of colours, OK led flashing and a possible, suitably programmed, flasher connected to the outputs of the control unit.
-
Page 16: Ce Declaration Of Conformity
TECHNICAL SPECIFICATIONS OF THE PRODUCT WARNINGS: • All technical specifications stated herein refer to an ambient temperature of 20° C (± 5° C). • Nice S.p.A. reserves the right to apply modifications to products at any time when deemed necessary, maintaining the same intended use and functionality.
-
Page 17
“partly completed machinery” Note: the contents of this declaration correspond to that stated in the official document filed in the offices of Nice S.p.A. and, in particular, the latest version thereof available prior to the printing of this manual. The text herein has been re-edited for editorial purposes. A copy of the original declaration can be requested from Nice S.p.A. -
Page 18
Nice SpA Via Callalta, 1 31046 Oderzo (TV) Italy www.niceforyou.com info@niceforyou.com…
ENGLISH
original operating instructions in Italian
Contents
Pictures ………………………………………………………………………………………….I-II
2 — INSTALLATION ……………………………………………………………………………..2
2.3 — Typical system ……………………………………………………………………………2
4 — PROGRAMMING ………………………………………………………………………….6
4.1 — Control unit buttons ……………………………………………………………………6
4.4 — Learning about the Opening and Closing positions with an incremental ..
encoder …………………………………………………………………………………….6
4.5 — Operating modes ……………………………………………………………………….7
5.1 — Testing ………………………………………………………………………………………8
5.2 — Commissioning …………………………………………………………………………..8
6 — FURTHER DETAILS ………………………………………………………………………9
7 — DIAGNOSTICS ……………………………………………………………………………10
7.2 — Diagnostics ………………………………………………………………………………10
8 — PRODUCT DISPOSAL …………………………………………………………………11
Specifications:
|
Accompanying Data:
Nice DPRO924 Control Unit PDF Instructions And Warnings For Installation And Use (Updated: Friday 10th of March 2023 05:14:25 AM)
Rating: 4.8 (rated by 2 users)
Compatible devices: MC424L, ROBO RO1040, A0 Series, HSTS2, UDL 2, mindy A60, BiDi-WiFi, MC800.
Recommended Documentation:
Nice DPRO924: Text of Manual, Instructions And Warnings For Installation And Use
(Ocr-Read Version Summary of Contents, UPD: 10 March 2023)
-
12, 8 – English EN 5 TESTING AND COMMISSIONING The testing and commissioning phases are the most important when creating an automated system in order to ensure maximum safety. The testing procedure can also be performed as a periodic check of the automation devices. These phases must be performed by qualied and experienced personnel who must take charge of establi…
-
5, English – 1 EN GENERAL WARNINGS: SAFETY — INSTALLATION — USE (original instructions in Italian) CAUTION Important safety instructions. Follow all instructions as improper installation may cause serious damage CAUTION Important safety instructions. It is important for you to comply with these instructions for your own and other people’s safety. Keep these …
-
8, 4 – English EN Out2 Clean contact relay output (maximum resistive load 3A) Out3 Clean contact relay output (maximum resistive load 3A) IMPORTANT! — We DO NOT recommend that you connect any device or accessory not mentioned in this instruction manual. The manufacturer declines all responsibility whatsoever for any damage due to improper use of the various system devices that does not comply wit…
-
10, 6 – English EN 4.1 — Control unit buttons 8 The “OPEN”, “STOP” and “CLOSE” buttons are to be used to con- trol the automated system and for the programming phase OPEN STOP CLOSE ON A B 1 2 3 1 2 34 ON OFF OFF 4.2 — Total deletion of the control unit memory You can delete all the data stored on the control unit and restore it to its original…
-
11, English – 7 EN ‘hold-to-run’ mode, until synchronization of the encoder position is completed. To perform this procedure, follow the following instructions: 01. Select the type of motor, setting dip switches B-2 and B-3 to OFF OFF 1 2 3 B 02. Set dip switch A-1 to ON (A-2, A-3 and A-4 are OFF) OFF 1 2 3 4 ON A 03. Keep the STOP button pressed until the led is on wi…
-
9, English – 5 EN TABLE 2 SMXI, SMXIS Receiver in “Mode 1 or 2” output description Output No. 1 Step-by-Step Output No. 2 Partial open; factory setting: opens 1/4 of the stroke (this may be changed during the position acquisition phase or by using the Oview programmer) Output No. 3 Open Output No. 4 Close OXI, OXIT receiver programmed in “extended Mode 2” command description C…
-
18, www.niceforyou.com Nice SpA Via Callalta, 1 31046 Oderzo (TV) Italy [email protected] IS0662A00MM_31-07-2018
… -
6, 2 – English EN 1 PRODUCT DESCRIPTION AND INTENDED USE DPRO924 is a control unit to be used to automate sectional balanced doors. It can control motors with an encoder or Hall effect position control system or using electromechanical limit switches. DPRO924 is particularly suitable to be connected to Sumo motors and Opera System devices. Available accessories: receivers with “SM”…
Nice DPRO924: Recommended Instructions
FLX-TR-01, ONA14TA065, RMCARD202, Aspire 1360 Series, MCM240/37, VCS 10 Series II
-
SYMPTOM PROBABLE CAUSE REMEDYMain valve No pressure at valve inlet Check inlet pressurefails to openMain valve diaphragm assembly Disassemble, clean and polishinoperative stem, replace detective partsPilot Valve (CRD) not opening:1. No spring compression 1. Tighten adjusting screw2. Damaged spring 2. Disassemble and replace3.Spring guide not in place 3. Assemble properly4. Yoke dragging on inl …
90-48 2
-
i-on CompactQuick Setup GuideIntroduction This guide provides a quick overview of how to set up standard features of an i-on Compact control unit. Note: Details of all features and options are available in the i-on Compact Engineering Guide, and i-on Compact Admin & User Manual, which you can download from www.touchpoint-online.com.Step 1: Power-up the control unitAfter installing all hardwar …
i-on Compact 12
-
FireHawk™ M7Air MaskNFPA 1981: 2007 EditionNFPA 1982: 2007 EditionCBRN Agent Approved Air MaskOPERATION AND INSTRUCTIONSThis device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions:(1) This device may not cause harmful interference and (2) this device must accept any interference that may causeundesired operation.TAL 708 (L) Rev. 1 © MSA 2007 Prn …
FireHawk M7 44
-
Service Manual Controller SIGMA CONTROL 2 BLOWER ≥ 2.5.3 No.: 901700 10 EManufacturer:KAESER KOMPRESSOREN SE96410 Coburg • PO Box 2143 • GERMANY • Tel. +49-(0)9561-6400 • Fax +49-(0)9561-640130www.kaeser.com …
SIGMA CONTROL 2 184
-
TSSP57038www.vishay.comVishay Semiconductors Rev. 2.1, 10-Apr-20191Document Number: 82482THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000IR Receiver Modules for Remote Control SystemsDESIGN SUPPORT TOOLS AVAILABLEORDERING CODETaping:TSSP57038TT1 — top view t …
TSSP57038 10
-
Digital Buck and Boost Digital Power Module DPH3205 RuiDeng1~® ~ Digital Buck-Boost Supply Power Module RUI DEMG Product model: DPH3205 r———————, General Information The constant voltage and constant current Digital control power supply module put the collection of analog integration and digital control functions in one. This module has power-down stored fu …
DPH3205 6
-
0102030405060708090100110-20 -15 -10 -5 0 5 10 15 20 25 30 35 40 45 50 55 60 65Percentage of Max Load (%)Surrounding Air Temperature (oC)Eingang (DC)Nenn-Eingangsspannung 24VdcSpannungsbereich 24-28VdcMaximale Eingangsspannung 30 ± 0,5VdcEingangsstrom Lademodus: 2,0 ± 1,0A (25°C)Entlademodus: Max. 40AMaximale Einschaltstrom (Kaltstart) < 45A (25°C)Ladedauer < 3 …
DRU-24V40ABN 2
-
www.wavetronix.com 801.734.7200Click 110 Contact ClosureINSTALLATION QUICK START GUIDE1 Mount and connect the deviceUse the following steps to install the Click 110 rack card:1 If you’re using hardware configuration, set all DIP switches before installing Click 110 devices (see step 3).2 Insert the card into the rack and daisy-chain all the cards in your installation togeth …
Click 110 2
-
Preface, ContentsCommunication via Ethernet CPsin S7 Stations1Installing and Starting theEthernet CP with STEP 72SEND/RECEIVEinterface3Configuring Communication Connections4Programming Functions (FCs)5NCM S7 Diagnostics6Firmware Loader7AppendixReferencesAGlossaryBLinking to Other Systems withFETCH/WRITECDocument HistoryDIndexManualfor NCM S7 V5.2 and higher11/2 …
NCM S7 222
-
(1) AC9930 Power Adapter for Access Point or Network Hub Student Kit(4) Network Hubs (1) Charging Bay(4) Network Hub Clamps (16) Data Cables(1) AC9940 power adapter for charging bay (4) Network Connectors The TI-Navigator™ System OverviewAccess Point connects to teacher’s computer through USB cable.Charging Bay charges network hubs when they are not in use. Co …
TI-Navigator 2
Additional Information:
Popular Right Now:
Operating Impressions, Questions and Answers:
Блок управления D-Pro924 предназначен для одного электропривода 24В секционных ворот серии Sumo.
Особенности
Блок управления воротами Nice DPRO924 разработан для любых приводов Nice, имеющих механические или электронные концевые выключатели, например Sumo SU2000, SU2010, SU2000V, SU2000VV. К нему подойдут радиоприёмники Nice с разъемом SM, например OXI или OXIBD.
Блок управления для промышленных ворот D-Pro924 работает как в полностью автоматическом режиме, так и с присутствием оператора. На крышке блока имеются кнопки управления приводом ворот, а также дисплей для контроля параметров и настройки.
Особенностью нового блока управления DPRO924 для приводов Sumo является наличие функции Smart, позволяющей программировать или контролировать состояние блока управления через смартфон.
Безопасное функционирование в любых режимах и соответствие стандарту 12453:2014 подтверждено европейским сертификатом TÜV NORD CERT GmbH
Технические характеристики блока управления Nice DPRO924:
Питание (переменный ток 50/60 Гц) 230В
Максимальная мощность двигателя привода 2,2кВт
Потребляемая мощность в режиме ожидания менее 4Вт
Вход предварительного концевого выключателя: программируемый
Внешние входные сигналы: Вверх, вниз, стоп, шаг за шагом, все программируемые
Выходы: три свободно программируемых выхода
Входной сигнал остановка: для датчиков с нормально замкнутым и нормально разомкнутым контактами, фотоэлементов, с активным сопротивлением 8,2 кОм и пневматических 8,2 кОм
Выход для обслуживания: 24 В постоянного тока, максимально 600 мА
Рабочая температура (°C): от -20 до +50
Класс защиты: IP65
Размеры (мм): 210x125x310
Масса: 3,5кг
Блок управления NICE DPRO924
NICE DPRO924 — это блок управления со встроенным 3-х позиционным постом управления (Открыть-Стоп-Закрыть), предназначенный для приводов NICE серии SUMO с возможностью управления воротами в присутствии оператора. Оснащен специальным разъемом Bus T4 с поддержкой всего функционала системы NiceOpera и возможностью подключения программирующего устройства OVIEW/A (поставляется отдельно). Блок управления поддерживает программирование основных функций с помощью Dip-переключателей (выбор типа двигателя, присутствие оператора (промышленный режим), управление энкодером или механическими концевыми выключателями, настройка чувствительности и др.). Блок управления оснащен специальным разъемом SM, позволяющим использовать все современные радиоприемники компании NICE, в том числе с технологиями BiDirection и LoRa.
Также блок управления NICE DPRO924 позволяет подключить следующее дополнительное оборудование и аксессуары:
• Внешняя антенна NICE ABF
• Сигнальная лампа NICE ELDC
• Встраиваемые радиоприемники OXI, SMXI, SMXIS, OXIBD и OXILR
• Внешний радиоприемник NICE OX2
• Резервная батарея NICE PS224
• Wi-Fi модуль NICE IT4WIFI
• Фотоэлементы безопасности (релейные): NICE EPM или EPS, NICE F210 или FT210
Купить блок управления NICE DPRO924 для автоматики NICE и выбрать удобный способ доставки Вы можете в нашем интернет-магазине, положив необходимое количество оборудования в корзину и оформив заказ on-line или же связавшись с отделом продаж по телефону: 8 800 302 22 53.
Расскажем о том, как сделать правильный выбор при самостоятельном подпоре и покупке автоматики для откатных ворот. На что, в первую очередь, следует обратить внимание, для исключения проблем при дальнейшей эксплуатации воротной автоматики.