P85 d3 gigabyte мануал

1. Manuals
2. Brands
3. Gigabyte Manuals
4. Motherboard
5. GA-P85-D3
6. User manual

• Page 1
  GA-P85-D3 User’s Manual Rev. 2001 12ME-P85D3-2001R…
• Page 2
  Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE. Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE’s prior written permission.

• Page 3: Table Of Contents

  Table of Contents GA-P85-D3 Motherboard Layout ………………4 GA-P85-D3 Motherboard Block Diagram ……………5 Chapter 1 Hardware Installation ………………6 Installation Precautions ………………. 6 Product Specifications ………………7 Installing the CPU ……………….. 9 Installing the Memory ………………10 Installing an Expansion Card …………….. 10 Back Panel Connectors ……………..

• Page 4: Ga-P85-D3 Motherboard Layout

  GA-P85-D3 Motherboard Layout ATX_12V_2X4 CPU_FAN KB_MS LGA1150 R_USB R_USB30 USB_LAN AUDIO PCIEX1 SYS_FAN3 GA-P85-D3 PCIEX16 B_BIOS Realtek ® M_BIOS GbE LAN PCI1 CODEC Intel ® PCI2 SATA3 PCI3 SATA2 5 4 PCI4 ® Super I/O PCIe to PCI Bridge PCIEX4…

• Page 5: Ga-P85-D3 Motherboard Block Diagram

  GA-P85-D3 Motherboard Block Diagram 1 PCI Express x16 CPU CLK+/- (100 MHz) LGA1150 DDR3 1600/1333 MHz PCIe CLK HDMI (100 MHz) Dual Channel Memory DMI 2.0 PCI Express Bus Dual BIOS RJ45 4 SATA 6Gb/s PCIe CLK Realtek ® (100 MHz)

• Page 6: Chapter 1 Hardware Installation

  Chapter 1 Hardware Installation Installation Precautions The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user’s manual and follow these procedures: • Prior to installation, make sure the chassis is suitable for the motherboard. •…

• Page 7: 1-2 Product Specifications

  Š Support for non-ECC memory modules Š Support for Extreme Memory Profile (XMP) memory modules Š (Go to GIGABYTE’s website for the latest supported memory speeds and memory modules.) Onboard Integrated Graphics Processor: Š 1 x HDMI port, supporting a maximum resolution of 4096×2160 Graphics * Support for HDMI 1.4a version.

• Page 8
  Internal 1 x 24-pin ATX main power connector Š 1 x 8-pin ATX 12V power connector Connectors Š 4 x SATA 6Gb/s connectors Š 2 x SATA 3Gb/s connectors Š 1 x CPU fan header Š 3 x system fan headers Š…

• Page 9: Installing The Cpu

  ATX Form Factor; 30.5cm x 20.0cm Form Factor Š * GIGABYTE reserves the right to make any changes to the product specifications and product-related information without prior notice. * Please visit the Support & DownloadsUtility page on GIGABYTE’s website to check the supported operating system(s) for the software listed in the «Unique Features»…

• Page 10: Installing The Memory

  • Make sure that the motherboard supports the memory. It is recommended that memory of the same capacity, brand, speed, and chips be used. (Go to GIGABYTE’s website for the latest supported memory speeds and memory modules.) • Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage.

• Page 11
  HDMI Port The HDMI port is HDCP compliant and supports Dolby True HD and DTS HD Master Audio formats. It also supports up to 192KHz/24bit 8-channel LPCM audio output. You can use this port to connect your HDMI-supported monitor. The maximum supported resolution is 4096×2160, but the actual resolutions supported are dependent on the monitor being used.

• Page 12: Internal Connectors

  Internal Connectors ATX_12V_2X4 F_AUDIO SPDIF_IN CPU_FAN SPDIF_O SYS_FAN1/2/3 F_USB30 SATA3 0/1/2/3 F_USB1/F_USB2 SATA2 4/5 COMB F_PANEL CLR_CMOS Read the following guidelines before connecting external devices: • First make sure your devices are compliant with the connectors you wish to connect. •…

• Page 13
  1/2) ATX_12V_2X4/ATX (2×4 12V Power Connector and 2×12 Main Power Connector) With the use of the power connector, the power supply can supply enough stable power to all the com- ponents on the motherboard. Before connecting the power connector, first make sure the power supply is turned off and all devices are properly installed.
• Page 14
  PORT PORT DEBUG DEBUG PORT PORT 5) SATA3 0/1/2/3 (SATA 6Gb/s Connectors) The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA 1.5Gb/s standard. Each SATA connector supports a single SATA device. SATA3 Pin No. Definition DEBUG DEBUG PORT…
• Page 15
  F_PANEL (Front Panel Header) Connect the power switch, reset switch, speaker, and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables. • PLED/PWR (Power LED, Yellow/Purple): Power LED Power Switch Speaker…
• Page 16
  10) SPDIF_IN (S/PDIF In Header) This header supports digital S/PDIF In and can connect to an audio device that supports digital audio out via an optional S/PDIF In cable. For purchasing the optional S/PDIF In cable, please contact the local dealer.
• Page 17
  14) COMB (Serial Port Header) The COM header can provide one serial port via an optional COM port cable. For purchasing the optional COM port cable, please contact the local dealer. Pin No. Definition Pin No. Definition NDCD- NDSR- NSIN NRTS- NSOUT NCTS-…

• Page 18: Chapter 2 Bios Setup

  To access the BIOS Setup program, press the <Delete> key during the POST when the power is turned on. To upgrade the BIOS, use either the GIGABYTE Q-Flash or @BIOS utility. Q-Flash allows the user to quickly and easily upgrade or back up BIOS without entering the operating •…

• Page 19
  M.I.T. This section provides information on the BIOS version, CPU base clock, CPU frequency, memory frequency, total memory size, CPU temperature, Vcore, and memory voltage. Whether the system will work stably with the overclock/overvoltage settings you made is dependent on your over- all system configurations.
• Page 20
  & K OC (Note) Allows for increased performance by using certain CPUs. (Default: Auto) & CPU PLL Selection Allows you to set the CPU PLL. Auto lets the BIOS automatically configure this setting. (Default: Auto) & Filter PLL Level Allows you to set the Filter PLL. Auto lets the BIOS automatically configure this setting. (Default: Auto) &…
• Page 21
  & CPU Thermal Monitor (Note 1) Enables or disables Intel ® CPU Thermal Monitor function, a CPU overheating protection function. When enabled, the CPU core frequency and voltage will be reduced when the CPU is overheated. Auto lets the BIOS automatically configure this setting. (Default: Auto) &…
• Page 22
  & Profile DDR Voltage When using a non-XMP memory module or Extreme Memory Profile (X.M.P.) is set to Disabled, the value is displayed according to your memory specification. When Extreme Memory Profile (X.M.P.) is set to Profile1 or Profile2, the value is displayed according to the SPD data on the XMP memory. &…
• Page 23
  & CPU Fan Speed Control (CPU_FAN Connector) Allows you to determine whether to enable the fan speed control function and adjust the fan speed. Allows the fan to run at different speeds according to the CPU temperature. You can Normal adjust the fan speed with EasyTune based on your system requirements.

• Page 24: System Information

  System Information This section provides information on your motherboard model and BIOS version. You can also select the de- fault language used by the BIOS and manually set the system time. & System Language Selects the default language used by the BIOS. &…

• Page 25: Bios Features

  A password is required for booting the system and for entering the BIOS Setup program. System (Default) & Full Screen LOGO Show Allows you to determine whether to display the GIGABYTE Logo at system startup. Disabled skips the GIGABYTE Logo when the system starts up. (Default: Enabled) — 25 -…

• Page 26
  & Fast Boot Enables or disables Fast Boot to shorten the OS boot process. Ultra Fast provides the fastest bootup speed. (Default: Disabled) & VGA Support Allows you to select which type of operating system to boot. Enables legacy option ROM only. Auto EFI Driver Enables EFI option ROM.
• Page 27
  & Windows 8 Features Allows you to select the operating system to be installed. (Default: Other OS) & CSM Support Enables or disables UEFI CSM (Compatibility Support Module) to support a legacy PC boot process. Enables UEFI CSM. (Default) Always Disables UEFI CSM and supports UEFI BIOS boot process only.

• Page 28: Peripherals

  & User Password Allows you to configure a user password. Press <Enter> on this item, type the password, and then press <Enter>. You will be requested to confirm the password. Type the password again and press <Enter>. You must enter the administrator password (or user password) at system startup and when entering BIOS Setup.

• Page 29
  All shared ports are eventually routed to the xHCI controller during the BIOS boot Enabled process. If BIOS does not have pre-boot support for the xHCI controller, it should initially route the sharable ports to the EHCI controller and then prior to OS boot it should route the ports to xHCI controller.
• Page 30
  Configures the SATA controllers to AHCI mode. Advanced Host Controller Interface AHCI (AHCI) is an interface specification that allows the storage driver to enable advanced Serial ATA features such as Native Command Queuing and hot plug. (Default) ` Serial ATA Port 0/1/2/3/4/5 &…

• Page 31: Power Management

  Power Management & Power Loading Enables or disables dummy load. When the power supply is at low load, a self-protection will activate causing it to shutdown or fail. If this occurs, please set to Enabled. Auto lets the BIOS automatically configur this setting.(Default:Auto) &…

• Page 32: Save & Exit

  Keyboard 98 Press POWER button on the Windows 98 keyboard to turn on the system. Set a password with 1~5 characters to turn on the system. Password & Power On Password Set the password when Power On By Keyboard is set to Password. Press <Enter>…

• Page 33: Chapter 3 Appendix

  & Boot Override Allows you to select a device to boot immediately. Press <Enter> on the device you select and select Yes to confirm. Your system will restart automatically and boot from that device. & Save Profiles This function allows you to save the current BIOS settings to a profile. You can create up to 8 profiles and save as Setup Profile 1~ Setup Profile 8.

• Page 34: Regulatory Statements

  GIGABYTE products have not intended to add and safe from hazardous substances (Cd, Pb, Hg, Cr+6, PBDE and PBB). The parts and components have been carefully selected to meet RoHS requirement. More- over, we at GIGABYTE are continuing our efforts to develop products that do not use internationally banned toxic chemicals.

• Page 35
  FCC Notice (U.S.A. Only) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

• Page 36: Contact Us

  Tech. and Non-Tech. Support (Sales/Marketing) : http://ggts.gigabyte.com.tw WEB address (English): http://www.gigabyte.com WEB address (Chinese): http://www.gigabyte.tw You may go to the GIGABYTE website, select your language in the language list on the top right corner of the website. GIGABYTE Global Service System •…

MANUALSCAT | RU

Вопросы и ответы

У вас есть вопрос о Gigabyte GA-P85-D3, но вы не можете найти ответ в пользовательском руководстве? Возможно, пользователи ManualsCat.com смогут помочь вам и ответят на ваш вопрос. Заполните форму ниже — и ваш вопрос будет отображаться под руководством для Gigabyte GA-P85-D3. Пожалуйста, убедитесь, что вы опишите свои трудности с Gigabyte GA-P85-D3 как можно более детально. Чем более детальным является ваш вопрос, тем более высоки шансы, что другой пользователь быстро ответит на него. Вам будет автоматически отправлено электронное письмо, чтобы проинформировать вас, когда кто-то из пользователей ответит на ваш вопрос.