Panametrics at868 руководство по эксплуатации

Page 7: Table Of Contents

Contents Chapter 1. Installation Introduction ………………… .1 Unpacking .

Page 11: Chapter 1. Installation

Introduction To ensure safe and reliable operation of the Model AT868 Flowmeter, the system must be installed and programmed in accordance with the guidelines established by Panametrics engineers. Those guidelines, explained in detail in this chapter, include the following topics: •…

Page 12: Unpacking

The discarding of an important item along with the packing materials is all too common. If anything is missing or damaged, contact Panametrics immediately for assistance. Site Considerations Because the relative location of the flowcell and the electronics enclosure is important, use the guidelines in this section to plan the AT868 installation.

Page 13: Cable Lengths

Locate the electronics enclosure as close as possible to the flowcell/transducers, preferably directly on the flowcell. However, Panametrics can supply transducer cables up to 1000 ft (300 m) in length for remote location of the electronics enclosure. If longer cables are required, consult Panametrics for assistance.

Page 14: Preparing The Unit

Chapter 1. Installation 1.6.1 Preparing the Unit Prepare the unit as described below before making any electrical connections. Disconnect any previously wired power line from the unit. Remove the screws on the front cover. Remove the plastic shield that protects the electrical connections by loosening the two screws and lifting the plastic shield.

Page 15: Wiring Transducers

Chapter 1. Installation Either proceed to the next section to continue wiring the AT868 or reinstall the plastic shield, replace the front cover on the enclosure and tighten the screws. 1.6.3 Wiring Transducers WARNING! Before connecting the transducers, discharge any static buildup by shorting the center conductor of the transducer cables to the metal shield on the cable connector.

Page 16: Wiring Std 0/4-20 Ma Analog Outputs

Chapter 1. Installation 1.6.4 Wiring Std 0/4-20 mA Analog Outputs The Model AT868 flow transmitter has a pair of isolated 0/4-20 mA analog output per channel (designated as Output A and Output C). These outputs can be configured independently. Typically, Output A is used for Channel 1 and Output C is used for Channel 2.

Page 17: Wiring The Totalizer/Frequency Output

Chapter 1. Installation 1.6.5 Wiring the Totalizer/Frequency Output The Model AT868 also provides a second pair of outputs per channel (designated as Output B and Output D) that can be configured as a totalizer or frequency output. Like the analog outputs, these outputs can also be configured independently. Typically, Output B is used for Channel 1 and Output D is used for Channel 2.

Page 18: Wiring The Serial Port

Signal names that imply direction (e.g., transmit and receive) are named from the point of view of the DTE device, which is usually the Panametrics meter. When the RS232 standard is strictly followed, these signals are labeled with the same name and pin # on the DCE device side as well. Unfortunately, that convention is not followed because the DTE and DCE side get confused.

Page 20: Wiring An External Totalizer Reset Switch

Chapter 1. Installation 1.6.6.4 Using a Factory-Configured Serial Interface Use the following steps to link the AT868 to the control system using a factory-configured RS485 interface: See “Preparing the Unit” on page 4 before you connect the power. Feed the wires through the conduit hole and wire lead TMT+ to pin 2 (RX) on the COMMUNICATION terminal block (refer to Figure 4 on page 12 for the terminal block location).

Page 23: Chapter 2. Programming Site Data

The AT868 flow transmitter has a user program that provides access to the various programmable features of the unit. To program the AT868 you can use either the internal keypad or Panaview ™, a PC-based, non-resident Panametrics software program that communicates with the AT868 through its serial port. Note: If you are using Panaview , the AT868 is configured with the Meter Address as 1 and the baud rate as 9600.

Page 24: Activating A Channel/Path — Chx-Activ

Chapter 2. Programming Site Data Activating a Channel/Path — CHx-ACTIV The ACTIV submenu is used to activate/deactivate the channel/path. The channel/path should be activated when you receive your unit; however, you should verify that the channel/path is active before you begin programming. While following the programming instructions, refer to Figure 9 on page 85 .

Page 25: Entering System Data For A Channel/Path — Chx-Systm

Chapter 2. Programming Site Data Entering System Data for a Channel/Path — CHx-SYSTM The CHx-SYSTM submenu is used to enter system parameters for the individual channels/paths. When channels/paths operate separately, the AT868 uses the system parameters in this menu. When channels/paths are averaged together, the AT868 uses parameters selected in the GLOBL-SYSTM submenu.

Page 26: Selecting The Totalizer Units

Chapter 2. Programming Site Data 2.3.3 Selecting the Totalizer Units Use the arrow keys to select the desired units for the totalized flow rate display and press [ENTER]. Use the arrow keys to select the desired number of digits to the right of the decimal point in the totalized flow rate display and press [ENTER].

Page 27: Entering Transducer And Pipe Parameters — Chx-Pipe

Chapter 2. Programming Site Data Entering Transducer and Pipe Parameters — CHx-PIPE Enter the transducer and pipe parameters via the PIPE submenu. While following the programming instructions, refer to Figure 9 on page 85 . Remember to record all programmed data in Appendix C, Data Records . 2.4.1 Accessing the PIPE Submenu Press [ESC], [ENTER], [ESC] to enter the user program.

Page 28: Special Transducers

to increase or decrease the number and press [ENTER].  Enter the wedge sound speed (supplied by Panametrics) of the transducer by using the arrow keys. Press [   …

Page 29: Pipe Material

Chapter 2. Programming Site Data 2.4.4 Pipe Material If a standard clamp-on transducer is being used, the programming sequence should be rejoined here.   Press [ and [ ] to select one of the pipe materials listed in Table 2 below and press [ENTER]. Note: Some of the pipe materials require additional selections.

Page 30: Pipe Outside Diameter

Obtain the required information by measuring either the pipe outside diameter (OD) or circumference at the transducer installation site. The data may also be obtained from standard pipe size tables found in the Panametrics Sound Speeds and Pipe Size Data reference (914-004). …

Page 31: Lining

Chapter 2. Programming Site Data 2.4.7 Lining   Press [ and [ ] to select whether the pipe has a lining and press [ENTER]. Do one of the following: If you selected No, proceed to “Setting Up a Tracking Window” on page 21 and “Fluid Type” on page 22. •…

Page 32: Fluid Type

Chapter 2. Programming Site Data 2.4.9 Fluid Type  The selections for fluid type vary depending on whether the Tracking Window is enabled or disabled. Press [  ] to select the desired fluid and press [ENTER]. Refer to Table 3 below for a list of available fluids. and [ Table 3: Fluid Types Tracking Windows =…

Page 33: Kv Input Selection

Chapter 2. Programming Site Data 2.4.11 KV Input Selection   Press [ and [ ] to enter a static kinematic viscosity or a table of values and press [ENTER]. Do one of the following:   • If you selected Table, enter the Calibration Factor by using the arrow keys. Press [ and [ ] to move the and…

Page 34: Entering The Zero Cutoff Value — Chx-I/O

Chapter 2. Programming Site Data Entering the Zero Cutoff Value — CHx-I/O Near a zero flow rate, the Model AT868 readings may fluctuate due to small offsets caused by thermal drift or similar factors. To force a zero display reading when there is minimal flow, enter a zero cutoff value as described below. While programming these parameters, refer to Figure 9 on page 85 .

Page 35: Set Transducer Signal Settings — Signl

Chapter 2. Programming Site Data 2.6.1 Set Transducer Signal Settings — SIGNL Use this option to set the limits for the incoming signal and other parameters affecting the transducer signal. For example, the programmed signal strength low limit may be used to determine the trigger point for an alarm. CAUTION! The SIGNL default settings are suitable for most applications.

Page 36: Setting Response Time — Avrg

Chapter 2. Programming Site Data Table 4: Transducer Signal Parameters (cont.) Transducer Signal Parameters Range Default Value Description Amplitude 0 to 100 The amplitude measures the transducer signal received by the Discriminator Model AT868. The E5: AMPLITUDE error message appears when the amplitude discriminator falls below the programmed AMP.

Page 37: Initializing Setup Parameters — Init

Chapter 2. Programming Site Data Procedure Options After completing the above step, the user program returns to the SET UP window. Do one of the following: • To continue regular programming, refer to Appendix A, Menu Maps , to navigate to the desired menu. •…

Page 42: Entering Global System Data — Globl-Systm

Chapter 2. Programming Site Data Entering Global System Data — GLOBL-SYSTM While completing these instructions, refer to Figure 10 on page 86. Remember to record all programmed data in Appendix C, Data Records . Proceed to the following sections to enter system information in the GLOBL menu. 2.7.1 Selecting the GLOBL-SYSTM Units Press [ESC], [ENTER], [ESC] to enter the user program.

Page 43: Setting Up The External Totalizer Reset Switch

To connect an external reset switch, refer to “Wiring an External Totalizer Reset Switch” on page 10 . IMPORTANT: The hardware for the switch is user-supplied. Panametrics provides only the software needed to configure the switch and the terminals used to connect the switch.

Page 44: Selecting Mass Flow Units

Chapter 2. Programming Site Data 2.7.4 Selecting Mass Flow Units   Press [ and [ ] to select the desired mass flow units for the flow rate display and press [ENTER]. The available units for this prompt are determined by the selection made at SYSTEM UNITS on the previous page. …

Page 45: Setting Up The Inputs And Outputs — Globl-I/O

Chapter 2. Programming Site Data Setting Up the Inputs and Outputs — GLOBL-I/O Set up the AT868 inputs and outputs via the Input/Output menu. While following the programming instructions, refer to Figure 10 on page 86 . Remember to record all programmed data in Appendix C, Data Records . The GLOBL-I/O submenu consists of the following options: •…

Page 47: Setting Up Analog And Totalizer/Frequency Outputs — Optn

Chapter 2. Programming Site Data 2.8.2 Setting Up Analog and Totalizer/Frequency Outputs — OPTN The AT868 has one built-in analog output and one totalizer/frequency output for each channel which must be set up. To accomplish this, refer to one of the following sections: •…

Page 52: Configuring The Communications Port — Globl-Comm

Chapter 2. Programming Site Data Configuring the Communications Port — GLOBL-COMM The AT868 flow transmitter is equipped with a built-in serial communications port. The standard port is an RS232 interface. However, an RS485 interface is available upon request. The AT868 can receive and execute remote commands with PanaView , by connecting the meter’s serial interface to the serial port of a PC.

Page 53: Configuring An Output As A Totalizer Or Frequency Output

Chapter 2. Programming Site Data 2.10 Configuring an Output as a Totalizer or Frequency Output Outputs B and D can be configured as totalizer or frequency outputs using PanaView software. Before an output can be configured, the AT868 must be connected to a PC via its serial port (see “Wiring the Serial Port” on page 8 ). Complete the following steps to configure the output: Open the SITE EDIT MENU from the CALIBRATION/TEST menu.

Page 55: Chapter 3. Displaying Data

Chapter 3. Displaying Data Chapter 3. Displaying Data Introduction The AT868 flow transmitter is equipped with a Liquid Crystal Display (LCD), which may be programmed to display up to four variables in sequence. To ease viewing, both the brightness and the contrast of the LCD are adjustable. In addition, this chapter discusses resetting the totalizers and pausing the measurements.

Page 56: Setting Up The Display

Chapter 3. Displaying Data Setting Up the Display Complete the following instructions to display the desired data on the display screen (see Figure 10 on page 86). 3.3.1 Accessing the Display Submenu Press [ESC], [ENTER], [ESC] to enter the user program. …

Page 57: Resetting Totals

Chapter 3. Displaying Data Resetting Totals To reset the totals, you can use either the internal keypad, PanaView ™ software or an external switch. When resetting totals, the totals for both channels will be reset. Use the appropriate section below to reset the totalizers. 3.4.1 Resetting Totalizers Using the Internal Keypad Refer to Figure A-4 on page A-4 in Appendix A.,<Title Font>…

Page 58: Taking Measurements

Chapter 3. Displaying Data Taking Measurements PanaView ™ offers a unique command that enables you to pause and restart the measurements. When you pause the measurement, the AT868 suspends taking measurements. Therefore, all outputs are also affected. This option is only accessible using PanaView ™…

Page 59: Chapter 4. Calibration

Chapter 4. Calibration Chapter 4. Calibration Introduction Use this menu to calibrate and test the analog and totalizer/frequency outputs. Refer to Figure 12 on page 88 , while following the calibration instructions. Calibrating and Testing the Analog Outputs The AT868 flowmeter includes one built-in analog output per channel with a resolution of 5.0 A (0.03% full scale). Although one analog output is provided for each channel, the outputs are channel independent.

Page 60: Calibrating The Low End Of The Analog Output

] to select UP or DOWN to adjust the 4 mA reading and press [ENTER]. When the desired reading is achieved, select STORE. If the ammeter reading cannot be adjusted to within ±5.0 A of the 4 mA setting, select ABORT to end the calibration and contact Panametrics for assistance. 4.2.4 Calibrating the High End of the Analog Output …

Page 61: Testing The Output Linearity

Then, repeat the low and high end calibrations. If the analog output still does not pass the linearity test, contact Panametrics for assistance. Repeat Step 2 with a different output setting (0-100%). Check the ammeter reading at this setting and press [ENTER] when done.

Page 62: Testing The Totalizer/Frequency Outputs

Chapter 4. Calibration Testing the Totalizer/Frequency Outputs Prepare for the testing procedure by connecting a frequency counter to the appropriate terminal blocks, as shown in Figure 4 on page 12 . Note: Analog outputs 1 and 2 in the wiring diagram correspond to analog outputs B and D in the AT868 software. 4.3.1 Calibrating the Frequency Output Press [ESC], [ENTER], [ESC] to enter the user program.

Page 63: Chapter 5. Error Codes

Chapter 5. Error Codes Chapter 5. Error Codes Introduction The AT868 ultrasonic flow transmitter is a reliable, easy to maintain instrument. When properly installed and operated, as described in Chapter 1, Installation , the meter provides accurate flow rate measurements with minimal user intervention.

Page 64: E2: Sound Speed Error

Chapter 5. Error Codes E2: Sound Speed Error submenu of the User The sound speed exceeds the limits programmed in the Problem: SETUP-SIGNL Program . The error may be caused by incorrect programming, poor flow conditions or poor transducer Cause: orientation.

Page 65: E6: Cycle Skip, Accel

Chapter 5. Error Codes E6: Cycle Skip, Accel. submenu of the User The acceleration exceeds the limits programmed in the Problem: SETUP-SIGNL Program . This condition is usually caused by poor flow conditions or improper transducer alignment. Cause: Refer to Chapter 6, Diagnostics, , to correct any flowcell and/or transducer problems. Action: E7: Analog Out Error The current in the analog output circuit exceeds the limits for the analog output port.

Page 67: Chapter 6. Diagnostics

Chapter 6. Diagnostics Chapter 6. Diagnostics Introduction This chapter explains how to troubleshoot the AT868 if problems arise with the electronics enclosure, the flowcell, or the transducers. Indications of a possible problem include: • Display of an error message on the LCD screen •…

Page 68: Configuring The Display

Chapter 6. Diagnostics 6.2.2 Configuring the Display  At # of LCD PARAMS, press [ ] to select the desired number of parameters to be sequentially displayed and then press [ENTER]. For a 1-channel/path AT868, proceed to Step 3. For a 2-channel/path meter, proceed to Step 2. Note: If you select OFF , the meter returns to the Global I/O window.

Page 69: Using The Tracking Window

Chapter 6. Diagnostics Table 9: Available Diagnostic Parameters Option Bar Description Good NFup Displays the normalization factor for the upstream transducer. 0.85-1.0 <0.85 NFdn Displays the normalization factor for the downstream 0.85-1.0 <0.85 transducer. Cxdcr Displays the speed of sound in the transducer (clamp-on only). N.A.

Page 70: Configuring The Display

If the sound speed is not constant, leave the Tracking Window ON and reconfigure the display to show the desired measurements. Note: If you are unsure if the sound speed is fairly constant, consult Panametrics. 6.3.3 Deactivating the Tracking Window Press [ESC], [ENTER], [ESC] to enter the user program.

Page 71: Diagnostic Record

• Fluid problems • Pipe problems. Read the following sections carefully to determine if the problem is indeed related to the flowcell. If the instructions in this section fail to resolve the problem, contact Panametrics for assistance. 6.5.1 Fluid Problems Most fluid-related problems result from a failure to observe the flowmeter system installation instructions.

Page 72: Pipe Problems

The accuracy of the flow rate measurements is no better than the accuracy of the programmed pipe dimensions. For a flowcell supplied by Panametrics, the correct data ise included in the documentation. For other flowcells, measure the pipe wall thickness and diameter with the same accuracy desired in the flow rate readings.

Page 73: Transducer Problems

Because transducer problems are largely dependent on the type of transducers used, wetted or clamp-on, the following list of potential problems is grouped according to transducer type. Contact Panametrics if you cannot solve a transducer-related problem.

Page 74: Clamp-On Transducer Problems

To resolve a cycle skip, recouple both transducers with proper couplant. Check your couplant for temperature ranges. In addition, make sure the pipe wall is free of paint and rust. If the instructions in this section fail to resolve the problem, contact Panametrics for assistance. AquaTrans™ AT868 User’s Manual…

Page 75: Chapter 7. Parts Replacement

This service history may prove very helpful in diagnosing any future problems. Purchasing Parts To purchase the parts mentioned in this chapter or any items not specifically discussed, contact Panametrics for assistance. To make sure the proper components are obtained, be sure to specify the serial number of your AT868 at the time of purchase.

Page 76: Replacing The Lcd Display/Keypad

Chapter 7. Parts Replacement Replacing the LCD Display/Keypad The LCD display/keypad assembly normally provides years of dependable service, but it is easily field-replaceable when necessary. To replace the LCD display/keypad, see Figure 7 on page 71 and Figure 8 on page 72 for the component locations, and complete the following steps.

Page 77: Replacing The Fuse

Chapter 7. Parts Replacement Replacing the Fuse Complete the steps below to replace the AT868 fuse (refer to Figure 7 on page 71 ): Disconnect the power from the AT868 and move the electronics enclosure to a clean, flat work surface. WARNING! The main power to the Model AT868 must be disconnected before proceeding.

Page 78: Replacing The User Program

Chapter 7. Parts Replacement Replacing the User Program The AT868 User Program is stored on an erasable programmable read-only memory (EPROM) chip. The EPROM, which is designated as component U4, is mounted in a socket on the rear of the Channel 1 board. EPROM replacement may be required to replace a defective chip or to upgrade to a newer software version.

Page 79: Locating The Eprom

Chapter 7. Parts Replacement 7.5.2 Locating the EPROM Flip the Channel 1 board over and locate the U4 EPROM socket. It is the only socketed chip on this board and it has a white identification label. Using a chip puller, remove the EPROM from its socket. If a chip puller is unavailable, a straightened paper clip may be used in the notches at the upper right and lower left corners of the socket.

Page 85: Chapter 9. Specifications

Chapter 9. Specifications Chapter 9. Specifications General Specifications The general specifications for the AT868 flow transmitter are divided into the following categories: 9.1.1 Hardware Configuration Channel Options Standard : 1-Channel Optional: 2-Channel/Path (2 paths per pipe) Package Options: General purpose Type 4X powder-coated aluminum wall mount Dimensions: 2.2 lb (1 kg);…

Page 86: Rangeability

Chapter 9. Specifications 9.1.5 Rangeability 400:1 9.1.6 Repeatability Wetted Transducers :  0.2% of full scale Clamp-on Transducers :  0.2 to 0.5% of full scale Note: Specifications assume a fully developed flow profile, with a straight run of pipe 10 diameters upstream and 5 diameters downstream from the measurement point.

Page 87: Input/Output Specifications

Chapter 9. Specifications Input/Output Specifications Digital Display: 2-line x 16-character LCD display, LED backlight, configurable to display up to 4 measurement parameters in sequence Digital Communications: Standard: RS232 serial port for PC, terminal or printer Optional: RS485 serial port for PC, terminal or printer Analog Outputs: 1 isolated 0/4-20 mA, 600 …

Page 89: Transducer Specifications

Optional: Explosion-proof, Div. 1, Class 1, Group C&D, INIEX-Certified EEx d IIC T6 or weatherproof (Type 4, IP65) Other Options: Transducers for special applications; fixtures; no organic bonds or insulators; cooling jackets for high temperatures. Please consult Panametrics for details. AquaTrans™ AT868 User’s Manual…

Page 90: Clamp-On Transducers

Inside Diameter: 0.04 to 200 in. (1 mm to 5 m) and larger 9.5.2 Clamp-on Transducers Materials: 316 SS and most plastics (Consult Panametrics for concrete, composite materials and highly corroded or lined pipes.) Pipe Sizes: Outside Diameter: 0.5 to 200 in. (12.7 mm to 5 m) and larger Pipe Wall Thickness: Up to 3 in.

Page 91: Tilted Diameter Spoolpiece Specifications

Chapter 9. Specifications Tilted Diameter Spoolpiece Specifications Pipe Sizes: Standard: 2 to 200 in. (50 mm to 5 m), 100% interrogation Optional: > 200 in. Materials: Standard: SS, carbon steel, plastic or fiberglass Optional: Other metals, plastics, etc. Process Connections: Standard: Straight (welding), 150-lb flanged, 300-lb flanged and higher Optional: MJ, Victaulic, RTJ flanged or cold-tap Wetted Transducer Connections:…

Page 93: Appendix A. Menu Maps

Appendix A. Menu Maps Appendix A. Menu Maps This appendix includes the following AT868 menu maps: • Figure 9, “The CHx>ACTIV, SYSTM, PIPE, and I/O Menu Map,” on page 85 • Figure 10, “The GLOBL Menu Map,” on page 86 •…

Page 99: Appendix B. Ce Mark Compliance

Appendix B. CE Mark Compliance Appendix B. CE Mark Compliance Introduction For CE Mark compliance, the AT868 flow transmitter must comply with both the EMC and LVD directives. IMPORTANT: CE Mark compliance is required for all units intended for use in EU countries. EMC Compliance For EMC compliance, the electrical connections must be shielded and grounded as in Table 11 below.

Page 100: Lvd Compliance

Appendix B. CE Mark Compliance LVD Compliance For compliance with the European Union’s Low Voltage Directive, the AT868 requires an external power disconnect device such as a switch or circuit breaker. The disconnect device must be marked as such, clearly visible, directly accessible, and located within 1.8 m (6 ft) of the unit.

Page 101: Appendix C. Data Records

Appendix C. Data Records Appendix C. Data Records Site Data After the AT868 flow transmitter has been installed, specific site data must be entered via the User Program prior to operation. Record that information in Table 12 below. Table 12: Site Data General Information Model # Serial #…

Page 105: Appendix D. Measuring P And L Dimensions

To determine L, physically measure the distance between the center of the transducer ports at the inside wall as shown in Figure 15 below, if possible. If this is not possible in your installation, contact Panametrics for help. Pipe Thickness θ…

Page 107: Appendix E. Service Record

Appendix E. Service Record Appendix E. Service Record Introduction Whenever any service procedure is performed on the AT868, the details of the service should be recorded in this appendix. An accurate service history can prove very helpful in troubleshooting any future problems. Data Entry Record complete and detailed service information for your AT868 in Table 13 below.

Page 109: Diagnostic Parameters

Appendix E. Service Record Diagnostic Parameters After a successful initial installation of the AT868 and whenever any system malfunction is noticed, the values for the diagnostic parameters should be entered in Table 14 below. Table 14: Diagnostics Parameters Parameter Initial Current Parameter Initial…

Page 111: Appendix F. Programming With Panaview

For detailed installation and setup instructions, refer to the PanaView ™ User’s Manual (910-211). Wiring the RS232 Interface For details on wiring your RS232 interface, refer to “Wiring the Serial Port” on page 8 and to the Panametrics document EIA-RS Serial Communications (916-054).

Page 112: Setting Up The Communications Port

Appendix F. Programming with PanaView™ F.3.1 Setting Up the Communications Port Complete the steps below to establish communications with your AT868: Open the “New Meter Browser” window and expand the network tree. Then, highlight the My Computer(Name) branch by clicking on it. Drop down the “Edit”…

Page 114: Adding An Idm-Compatible Meter

Appendix F. Programming with PanaView™ Adding an IDM-Compatible Meter To add a meter on the IDM-configured communications port, complete the following steps: Highlight the communication port to which the meter will be added by clicking on it, and then open the “Edit” menu on the menu bar Note: if the communication port is not highlighted first, the “New Meter”…

Page 116: Editing Meter The Properties

Appendix F. Programming with PanaView™ Editing Meter the Properties With PanaView , you can edit the properties of your flow transmitter, such as: • Set the meter clock, or synchronize it with the PC clock • Read, plot and save transducer signals •…

Page 118: Setting The Meter Clock

Appendix F. Programming with PanaView™ F.5.1 Setting the Meter Clock The meter Time may be reset in three different ways: • Manually enter the time and date in the text box Click on the [Sync to PC] option button to have PanaView set the time and date to the current PC setting •…

Page 119: Reading The Transducer Signals

Appendix F. Programming with PanaView™ F.5.2 Reading the Transducer Signals To read a transducer Signal from the meter, proceed as follows: Click on the Read Signals button. For a 2-channel meter, open the Channel drop-down menu and click on the desired channel.

Page 120: Plotting The Transducer Signals

Appendix F. Programming with PanaView™ F.5.3 Plotting the Transducer Signals To plot the selected signal, click on Plot to open a graphical screen similar to Figure 28 below. Figure 28: Signal Graph Screen F.5.4 Saving the Transducer Signals To save the raw signal, click Save to open a screen similar to Figure 29 below. Enter the desired name, and click Save to save the signal as a text file.

Page 121: Clearing The Totalizers

Appendix F. Programming with PanaView™ F.5.5 Clearing the Totalizers To clear the meter totalizers, click on the Clear Totalizers button in the Properties screen. The meter totalizers are immediately reset to 0. F.5.6 Handling Site Files To access your site files, click on the Site Files button in the Properties Screen to open the Site File Operations screen shown in Figure 30 below.

Page 125: Changing Meter Settings

Appendix F. Programming with PanaView™ Changing Meter Settings With PanaView , the following remote programming tasks can be completed: • Program and change the meter operating parameters • Set up, start, and stop logs • Calibrate and test inputs and outputs •…

42, Chapter 2. Programming Site Data 32 AquaTrans™ AT868 User’s Manual 2.7 Entering Global System Data — GLOBL-SYSTM While completing these instructions, refer to Figure 10 on page 86. Remember to record all programmed data in Appendix C, Data Records . Proceed to the following sections to enter system information in the GLOBL menu. 2.7.1 Selecting the GLO…

101, AquaTrans™ AT868 User’s Manual 91 Appendix C. Data Records Appendix C. Data Records C.1 Site Data After the AT868 flow transmitter has been installed, specific site data must be entered via the User Program prior to operation. Record that information in Table 12 below. Table 12: Site Data General Information Model # Serial # Software Vers. Setup Date Global-System Meter Mes…

58, Chapter 3. Displaying Data 48 AquaTrans™ AT868 User’s Manual 3.5 Taking Measurements PanaView ™ offers a unique command that enables you to pause and restart the measurements. When you pause the measurement, the AT868 suspends taking measurements. Therefore, all outputs are also affected. This option is only accessible using PanaView ™ (refer to Figure …

18, Chapter 1. Installation 8 AquaTrans™ AT868 User’s Manual 1.6.6 Wiring the Serial Port The AT868 flow transmitter is equipped with a built-in serial communications port. The standard port is an RS232 interface, but an optional RS485 interface is available upon request. Proceed to the appropriate section for wiring instructions. For more information on ser…

96, Appendix A. Menu Maps AquaTrans™ AT868 User’s Manual 86 ESC ENTER ESC PROG RESET CALIB To enter the User Program press CH1 CH2* GLOBL (*for 2-Channel meters only) ENGMETRIC SYSTEM A-I/H 2 CHANNEL UNITS VOLUMETRIC UNITS Mf3/dGAL/S A-I/DBBL/S GAL/M A-F/S BBL/M GAL/H A-F/M BBL/H MGD A-F/H MBL/D ft3/s A-F/D A-I/S ft3/m f3/d A-I/M ft3/h BBL/D MBL/D Mm3/d ML/…

54, Chapter 2. Programming Site Data 44 AquaTrans™ AT868 User’s Manual [no content intended for this page]
…

76, Chapter 7. Parts Replacement 66 AquaTrans™ AT868 User’s Manual 7.3 Replacing the LCD Display/Keypad The LCD display/keypad assembly normally provides years of dependable service, but it is easily field-replaceable when necessary. To replace the LCD display/keypad, see Figure 7 on page 71 and Figure 8 on page 72 for the component locations, and complete the following…

85, AquaTrans™ AT868 User’s Manual 75 Chapter 9. Specifications Chapter 9. Specifications 9.1 General Specifications The general specifications for the AT868 flow transmitter are divided into the following categories: 9.1.1 Hardware Configuration Channel Options Standard : 1-Channel Optional: 2-Channel/Path (2 paths per pipe) Package Options: Genera…

16, Chapter 1. Installation 6 AquaTrans™ AT868 User’s Manual 1.6.4 Wiring Std 0/4-20 mA Analog Outputs The Model AT868 flow transmitter has a pair of isolated 0/4-20 mA analog output per channel (designated as Output A and Output C). These outputs can be configured independently. Typically, Output A is used for Channel 1 and Output C is used for Channel 2. Ho…

30, Chapter 2. Programming Site Data 20 AquaTrans™ AT868 User’s Manual 2.4.5 Pipe Outside Diameter The programming sequence should be rejoined here for all transducers. 1. Press [ ] to move the cursor to the outside diameter units and press andto select the desired units and press [ENTER]. 2. Enter the known pipe outside diameter or circumfe…

49, AquaTrans™ AT868 User’s Manual 39 Chapter 2. Programming Site Data 2.8.2.3 Accessing a Totalizer/Frequency Output These outputs can be configured for frequency or totalizer output using Panametrics’s PanaView ™ software. The totalizer output issues one pulse per each selected volume of flow. The meter produces a pulse each time the programmed amount of flow passes through…

86, Chapter 9. Specifications 76 AquaTrans™ AT868 User’s Manual 9.1.5 Rangeability 400:1 9.1.6 Repeatability Wetted Transducers :  0.2% of full scale Clamp-on Transducers :  0.2 to 0.5% of full scale Note: Specifications assume a fully developed flow profile, with a straight run of pipe 10 diameters upstream and 5 diameters downstream from the measurement…

77, AquaTrans™ AT868 User’s Manual 67 Chapter 7. Parts Replacement 7.4 Replacing the Fuse Complete the steps below to replace the AT868 fuse (refer to Figure 7 on page 71 ): 1. Disconnect the power from the AT868 and move the electronics enclosure to a clean, flat work surface. 2. Loosen the six set screws on the front cover, and remove the front cover. 3. Remove the four screw…

User Guide Wireless Video/Audio SenderTransmit and Receive Video and Audio, even through walls48659YEARSWARRANTY AFTER SALES SUPPORTwww.unisupport.com076 60 600 29IRE08 458 684 540GB 1 X Transmitter1 X Receiver2 x Power Adaptors2 x A/V Connection Cables2 x RCA-SCART Adaptors1 X IR Remote Signal Extension Wire1 X User Manual1 X Warranty DocumentationNow you have purchas …

48659 14

User’s Manual2.4GHz Long Range HDCD DigitalWireless Audio Transmitter Packing list1. Wireless Transmitter×1 2. Power Adapter×13. 3.5mm Audio Cable×1 4. 3.5mm Convert RCA Audio Cable×15. Charging Cable ×1 6. 6.5mm(male）to 3.5mm(female) adapter ×1 7. Antenna ×1 8. User’s Manual×1IntroductionTA001 developed by Eshow …

TA001 2

H/EN/2000-HART/02-2016/23 KLAY INSTRUMENTS B.V. INSTRUCTION MANUAL («HART») «INTELLIGENT» PRESSURE- AND LEVEL TRANSMITTERS SERIES 2000-SAN SERIES 2000 SERIES CER-2000 SERIES 2000-HYDROBAR WARNING Read th …

2000-SAN Series 26

OperationAll menu screenshots are take from FMT5The m Initial preparation work First set up the antenna cable and connect it to the transmitter’s RFOUT port, then plug the power cord into the transmitter’s power outlet. Next, the outlet is divided into two channels. Connection is complete, please turn on the transmitter panel POWER button, the devi …

FMT5.0 Series 7

The Spektrum trademark is used with permission of Bachmann Industries, Inc.DX5e Quick Start Guide 1. Install Receiver Example of AR500 installed in E-flite® Apprentice Though in general it is non-critical, optimum installation of the antenna is to orient the tip of the long antenna perpendicular to the short antenna. The tip on the long antenn …

DX5e 1

25-62-11Page 1 of 90APR 06/10570-5000 Rev. CInitial Issue JUN 30/1999Wulfsberg Electronics Division6400 Wilkinson Rd., Prescott, AZ 86301Cage Code: 1B7G3Abbreviated Component Maintenance ManualThis manual includes data for the equipment that follows:ComponentPart No. Model No.C406-2 SERIESEMERGENCY LOCATOR TRANSMITTEREmergency Locator Transmitter 453-5000 C406-2Emergency Locator Tra …

C406-2 SERIES 90

“APEMCO N4297-5V4 w9a No. 5716 DOOR/WINDOW TRANSMI-ITER (With Built-in Reed Switch, Magnet Separate) INSTALLATlOti INSTRUCUONS GENERAL The 5716 Door and Window Transmitter is small in size for unobtrusive use on doors and windows. It transmits up to 200-feet (30m) range, indoors. The No. 5716 includes a three minute transmit — inhibit delay. …

5716 2

IPAW6-10 Personal transmitter Persönlicher Funksender Transmisor personal Trasmettitore personale Personlig sändarenhet Émetteur personnel Intrunet Persoonlijke zender STEP: A6V10372530_b Edition: 05.02.2016 CADIM: V54538-F108-A100 P/N 7121897 Rev. A English Installation Instruction Before starting to setup and use this device, please read the Safety Instructions. Contents  I …

IPAW6-10 4

PD301 — PD306 Head Mount SMART TEMPERATURE TRANSMITTERS PRECISION DIGITAL CORPORATION 89 October Hill Road • Holliston MA 01746 USA Tel (800) 343-1001 • Fax (508) 655-8990 www.predig.com HART® Non-HART • Smart Temperature Transmitters with HART® Protocol • Universal Input: RTD, TC, Ohm & mV • Program with PC or HART Communicator • …

ExSense Series 36

T14SG SOFTWARE UPDATE MANUAL[Updating procedure]1. SD card format1. You will rst want to format your SD card to the 14SG. If you are using an existing SD card, any data previously saved to it will be deleted during the «format». We suggest you either save this data on your computer or purchase a new card.2. After inserting the new SD card into the t …

T14SG 10