Руководство по эксплуатации автомагнитолы pioneer mvh 150ub

Support for MVH-150UB

Найти продукт

Раздел: Авто, мото оборудование и транспорт

Тип: Автомагнитола

Инструкция к Автомагнитоле Pioneer MVH-150UB

RDS MEDIA CENTER RECEIVER

ЦИФРОВОЙ МЕДИА—РЕСИВЕР

English Русский

MVH-150UB

Owner’s Manual

Руководство пользователя

Thank you for purchasing this PIONEER

About this unit

Head unit

product

To ensure proper use, please read through this

The tuner frequencies on this unit are allocated

manual before using this product. It is especially

for use in Western Europe, Asia, the Middle

important that you read and observe WARN-

East, Africa and Oceania. Use in other areas

INGs and CAUTIONs in this manual. Please

may result in poor reception. The RDS (radio

keep the manual in a safe and accessible place for

data system) function only operates in areas

future reference.

with broadcasting RDS signals for FM stations.

CAUTION

! Do not allow this unit to come into contact

with liquids. Electrical shock could result.

Also, damage to this unit, smoke, and over-

heating could result from contact with

liquids.

If you want to dispose this product, do not

! The Pioneer CarStereo-Pass is for use only in

mix it with general household waste. There is

Germany.

a separate collection system for used elec-

! Always keep the volume low enough to hear

tronic products in accordance with legislation

outside sounds.

that requires proper treatment, recovery and

! Avoid exposure to moisture.

recycling.

! If the battery is disconnected or discharged,

any preset memory will be erased.

Private households in the member states of the

Note

EU, in Switzerland and Norway may return their

Function setting operations are completed even

used electronic products free of charge to desig-

if the menu is canceled before the operations

nated collection facilities or to a retailer (if you

are confirmed.

purchase a similar new one).

For countries not mentioned above, please con-

tact your local authorities for the correct method

About this manual

of disposal.

! In the following instructions, USB memories

By doing so you will ensure that your disposed

and USB audio players are collectively re-

product undergoes the necessary treatment, re-

ferred to as “USB storage device”.

covery and recycling and thus prevent potential

negative effects on the environment and human

health.

In case of trouble

Should this unit fail to operate properly, please

contact your dealer or nearest authorized

PIONEER Service Station.

a b

4

7

1 2 3 5

98c6

Display indication

21 3 75

Part Part

1 SRC/OFF 7 BAND

(back)/

MULTI-CONTROL

2

8

DIMMER

(M.C.)

(dimmer)

3

(list) 9 c/d

4 DISP a 1/

to 6/

AUX input jack

5 USB port b

(3.5 mm stereo

jack)

6

(equalizer) c Detach button

CAUTION

! Use an optional Pioneer USB cable (CD-

U50E) to connect the USB storage device as

any device connected directly to the unit will

protrude out from the unit, which could be

dangerous.

! Do not use unauthorized products.

9

Section

01

Before you start

Operating this unit

02

4 6 8

a

Indicator State

The list function is being oper-

1

(list)

ated.

Sub infor-

2

mation sec-

Sub information is displayed.

tion

TA (traffic

3

announce-

TA function is on.

ments)

TP (traffic

program

4

A TP station is tuned in.

identifica-

tion)

The sound retriever function

5

(sound re-

is on.

triever)

6 LOC Local seek tuning is on.

7

(repeat) Track or folder repeat is on.

(ran-

8

Random play is on.

dom)

2

En

Section

Operating this unit

Operating this unit

02

Notes

Indicator State

LANGUAGE (multi-language)

Removing the front panel to protect your unit from

! You can set up the menu options from the

English

theft

This unit can display the text information from a

system menu. For details about the settings,

! Tuner: band and fre-

1 Press the detach button to release the front

compressed audio file even for information em-

refer to System menu on page 7.

quency

panel.

bedded in English or Russian.

! You can cancel set up menu by pressing

! RDS: program service

2 Push the front panel upward (M) and then pull

Main infor-

! If the embedded language and the selected

SRC/OFF.

name, PTY information

it toward (N) you.

9

mation sec-

language setting are not the same, text infor-

and other literal informa-

tion

mation may not display properly.

tion

! Some characters may not be displayed prop-

Basic operations

! USB storage device:

erly.

elapsed playback time

Important

1 Turn M.C. to select the desired setting.

and text information

! Handle gently when removing or attaching

ENG (English)—РУС (Russian)

the front panel.

Appears when a lower tier of

2 Press M.C. to confirm the selection.

a

! Avoid subjecting the front panel to excessive

folder or menu exists.

3 Always keep the detached front panel in a pro-

CLOCK SET (setting the clock)

shock.

tection device such as a protection case.

! Keep the front panel out of direct sunlight

1 Turn M.C. to adjust hour.

and high temperatures.

Re-attaching the front panel

Set up menu

2 Press M.C. to select minute.

! To avoid damaging the device or vehicle inte-

1 Slide the front panel to the left.

3 Turn M.C. to adjust minute.

When you turn the ignition switch to ON after in-

rior, remove any cables and devices attached

Make sure to insert the tabs on the left side of

4 Press M.C. to confirm the selection.

to the front panel before detaching it.

the head unit into the slots on the front panel.

stallation, set up menu appears on the display.

You can set up the menu options below.

FM STEP (FM tuning step)

Normally, the FM tuning step employed by seek

1 After installation of this unit, turn the

tuning is 50 kHz. When AF or TA is on, the tuning

ignition switch to ON.

step automatically changes to 100 kHz. It may be

SET UP appears.

preferable to set the tuning step to 50 kHz when

AF is on.

2 Turn M.C. to switch to YES.

2 Press the right side of the front panel until it is

! The tuning step remains at 50 kHz during man-

# If you do not operate for 30 seconds, the set up

firmly seated.

ual tuning.

menu will not be displayed.

If you cannot attach the front panel to the

1 Turn M.C. to select the FM tuning step.

# If you prefer not to set up at this time, turn M.C.

head unit successfully, make sure that you are

50 (50 kHz)—100 (100 kHz)

to switch to NO. Press to select.

placing the front panel onto the head unit cor-

2 Press M.C. to confirm the selection.

If you select NO, you cannot set up in the set up

rectly. Forcing the front panel into place may

QUIT appears.

menu.

result in damage to the front panel or head

unit.

3 Press M.C. to select.

5 To finish your settings, turn M.C. to select

Turning the unit on

YES.

4 Perform the following procedures to set

1 Press SRC/OFF to turn the unit on.

# If you prefer to change your setting again, turn

the menu.

M.C. to switch to NO. Press to select.

Turning the unit off

To proceed to the next menu option, you need to

1 Press and hold SRC/OFF until the unit turns

confirm your selection.

6 Press M.C. to select.

off.

En

3

Section

02

Operating this unit

Operating this unit

2 Press one of the preset tuning buttons

Selecting a source

Tuner

Searching for an RDS station by PTY information

(1/

to 6/ ) to select the desired station.

1 Press SRC/OFF to cycle between:

You can search for general types of broadcasting

Basic operations

TUNER (tuner)—USB (USB)—AUX (AUX)

programs, such as those listed in the following

Switching the display

section. Refer to this page.

Adjusting the volume

Selecting a band

1 Press

(list).

1 Turn M.C. to adjust the volume.

1 Press BAND until the desired band (FM1,

Selecting the desired text information

2 Turn M.C. to select a program type.

FM2, FM3 for FM or MW/LW) is displayed.

1 Press DISP to cycle between the following:

NEWS/INFO—POPULAR—CLASSICS—

! FREQUENCY (program service name or

Switching preset stations

OTHERS

CAUTION

frequency)

1 Press c or d.

3 Press M.C. to begin the search.

For safety reasons, park your vehicle when re-

! BRDCST INFO (program service name/PTY

! Select PCH (preset channel) under SEEK to

The unit searches for a station broadcasting

moving the front panel.

information)

use this function. For details about the set-

that type of program. When a station is found,

! CLOCK (source name and clock)

tings, refer to SEEK (left/right key setting) on

its program service name is displayed.

Note

the next page.

! To cancel the search, press M.C. again.

When this unit’s blue/white lead is connected to

Notes

! The program of some stations may differ

the vehicle’s auto-antenna relay control termi-

Manual tuning (step by step)

! If the program service name cannot be ac-

from that indicated by the transmitted PTY.

nal, the vehicle’s antenna extends when this

1 Press c or d.

quired in FREQUENCY, the broadcast fre-

! If no station is broadcasting the type of

unit’s source is turned on. To retract the anten-

! Select MAN (manual tuning) under SEEK to

quency is displayed instead. If the program

program you searched for, NOT FOUND is

na, turn the source off.

use this function. For details about the set-

service name is detected, the program serv-

displayed for about two seconds and then

tings, refer to SEEK (left/right key setting) on

ice name will be displayed.

the tuner returns to the original station.

the next page.

! BRDCST INFO text information will change

Frequently used menu

automatically.

Seeking

operations

! Depending on the band, text information can

1 Press and hold c or d, and then release.

PTY list

be changed.

You can cancel seek tuning by briefly pressing

Returning to the previous display

! Text information items that can be changed

c or d.

NEWS/INFO (news and information)

Returning to the previous list (the folder one level

depend on the area.

While pressing and holding c or d, you can

NEWS (News), AFFAIRS (Current affairs), INFO

higher)

skip stations. Seek tuning starts as soon as

(Information), SPORT (Sports), WEATHER (Weath-

1 Press

/DIMMER.

you release c or d.

Using PTY functions

er), FINANCE (Finance)

Returning to the ordinary display

You can tune in to a station using PTY (program

Note

Canceling the main menu

type) information.

POPULAR (popular)

1 Press BAND.

This unit’s AF (alternative frequencies search)

POP MUS (Popular music), ROCK MUS (Rock

function can be turned on and off. AF should be

Returning to the ordinary display from the list

music), EASY MUS (Easy listening), OTH MUS

off for normal tuning operation (refer to AF (al-

1 Press BAND.

(Other music), JAZZ (Jazz), COUNTRY (Country

ternative frequencies search) on the next page).

music), NAT MUS (National music), OLDIES

(Oldies music), FOLK MUS (Folk music)

Storing and recalling stations

for each band

CLASSICS (classics)

L. CLASS (Light classical), CLASSIC (Classical)

Using preset tuning buttons

1 When you find a station that you want

to store in memory, press one of the preset

tuning buttons (1/

to 6/ ) and hold until

the preset number stops flashing.

4

En

Section

Operating this unit

Operating this unit

02

OTHERS (others)

Local seek tuning lets you tune in to only those

USB storage device

Switching the display

English

radio stations with sufficiently strong signals for

EDUCATE (Education), DRAMA (Drama), CUL-

Basic operations

good reception.

Selecting the desired text information

TURE (Culture), SCIENCE (Science), VARIED (Var-

1 Press M.C. to select the desired setting.

1 Press DISP to cycle between the following:

ied), CHILDREN (Children’s), SOCIAL (Social

FM: OFF—LV1—LV2—LV3—LV4

Playing songs on a USB storage device

MP3/WMA/WAV

affairs), RELIGION (Religion), PHONE IN (Phone

MW/LW: OFF—LV1 —LV2

1 Open the USB port cover.

! TRACK INFO (track title/artist name/album

in), TOURING (Travel), LEISURE (Leisure), DOCU-

The highest level setting allows reception of

2 Plug in the USB storage device using a USB

title)

MENT (Documentaries)

only the strongest stations, while lower levels

cable.

! FILE INFO (file name/folder name)

allow the reception of weaker stations.

Playback is performed automatically.

! ELAPSED TIME (track number and play-

Function settings

back time)

TA (traffic announcement standby)

Stopping playback of files on a USB storage de-

! CLOCK (source name and clock)

vice

1 Press M.C. to display the main menu.

! SPEANA (spectrum analyzer)

1 Press M.C. to turn traffic announcement

1 You may disconnect the USB storage device at

standby on or off.

any time.

2 Turn M.C. to change the menu option

Notes

The unit stops playback.

and press to select FUNCTION.

AF (alternative frequencies search)

! TRACK INFO and FILE INFO text information

Selecting a folder

will change automatically.

3 Turn M.C. to select the function.

1 Press M.C. to turn AF on or off.

1 Press 1/

or 2/ .

! Depending on the version of iTunes used to

Once selected, the following functions can be

write MP3 files to media file types, incompati-

NEWS (news program interruption)

Selecting a track

adjusted.

ble text stored within an audio file may be

1 Press c or d.

# If MW/LW band is selected, only BSM, LOCAL

displayed incorrectly.

1 Press M.C. to turn the NEWS function on or

and SEEK are available.

Fast forwarding or reversing

! Text information items that can be changed

off.

1 Press and hold c or d.

depend on the media.

BSM (best stations memory)

SEEK (left/right key setting)

! When playing compressed audio, there is no

sound during fast forward or reverse.

Selecting and playing files/

BSM (best stations memory) automatically stores

You can assign a function to the left and right keys

the six strongest stations in the order of their sig-

of the unit.

Returning to root folder

tracks from the name list

nal strength.

Select MAN (manual tuning) to tune up or down

1 Press and hold BAND.

1 Press

to switch to the file/track name

1 Press M.C. to turn BSM on.

manually or select PCH (preset channel) to switch

Switching between playback memory devices

list mode.

To cancel, press M.C. again.

between preset channels.

You can switch between playback memory devices

1 Press M.C. to select MAN or PCH.

REGION (regional)

on USB storage devices with more than one Mass

2 Use M.C. to select the desired file name

Storage Device-compatible memory device.

(or folder name).

When AF is used, the regional function limits the

1 Press BAND.

selection of stations to those broadcasting region-

! You can switch between up to 32 different

Selecting a file or folder

al programs.

memory devices.

1 Turn M.C.

1 Press M.C. to turn the regional function on or

off.

Note

Playing

1 When a file or track is selected, press M.C.

LOCAL (local seek tuning)

Disconnect USB storage devices from the unit

when not in use.

Viewing a list of the files (or folders) in the se-

lected folder

1 When a folder is selected, press M.C.

Playing a song in the selected folder

1 When a folder is selected, press and hold M.C.

En

5

Section

02

Operating this unit

Operating this unit

Operations using special buttons

Audio adjustments

Only frequencies lower than those in the selected

1 Press M.C. to display the setting mode.

range are outputted from the subwoofer.

1 Press M.C. to display the main menu.

2 Turn M.C. to select the equalizer.

Selecting a repeat play range

1 Press M.C. to display the setting mode.

POWERFUL—NATURAL—VOCAL—CUS-

1 Press 6/

to cycle between the following:

2 Press M.C. to cycle between the following:

2 Turn M.C. to change the menu option

TOM1—CUSTOM2—FLAT—SUPER BASS

! ALL – Repeat all files

Cut-off frequency—Output level—Slope level

and press to select AUDIO.

The equalizer band and equalizer level can be

! ONE – Repeat the current file

Rates that can be adjusted will flash.

customized when CUSTOM1 or CUSTOM2 is

! FLD – Repeat the current folder

3 Turn M.C. to select the desired setting.

3 Turn M.C. to select the audio function.

selected.

Playing tracks in random order

Cut-off frequency: 50HZ—63HZ—80HZ—

Once selected, the following audio functions

If selecting CUSTOM1 or CUSTOM2, complete

1 Press 5/

to turn random play on or off.

100HZ—125HZ—160HZ—200HZ

can be adjusted.

the procedures outlined below. If selecting

Tracks in a selected repeat range are played in

Output level: –24 to +6

! FADER is not available when SUB.W/SUB.W

other options, press M.C. to return to the pre-

random order.

Slope level: –6— –12

is selected in SP-P/O MODE. For details, refer

vious display.

! To change songs during random play, press d

to SP-P/O MODE (rear output and preout set-

! CUSTOM1 can be set separately for each

BASS BOOST (bass boost)

to switch to the next track. Pressing c restarts

ting) on the next page.

source.

playback of the current track from the begin-

! SUB.W, SUB.W CTRL and HPF SETTING are

! CUSTOM2 is a shared setting used in com-

1 Press M.C. to display the setting mode.

ning of the song.

not available when REAR/REAR is selected in

mon for all sources.

2 Turn M.C. to select a desired level.

SP-P/O MODE. For details, refer to

3 Press M.C. to display the setting mode.

0 to +6 is displayed as the level is increased or

Pausing playback

SP-P/O MODE (rear output and preout set-

4 Press M.C. to cycle between the following:

decreased.

1 Press 4/PAUSE to pause or resume.

ting) on the next page.

Equalizer band—Equalizer level

HPF SETTING (high pass filter adjustment)

Enhancing compressed audio and restoring rich

! SUB.W CTRL and HPF SETTING are not avail-

5 Turn M.C. to select the desired setting.

sound (sound retriever)

able when SUB.W is selected in OFF. For de-

Equalizer band: 80HZ—250HZ—800HZ—

When you do not want low sounds from the sub-

1 Press 3/S.Rtrv to cycle between:

tails, refer to SUB.W (subwoofer on/off

2.5KHZ—8KHZ

woofer output frequency range to play from the

1—2—OFF (off)

setting) on this page.

Equalizer level: +6 to –6

front or rear speakers, turn on the HPF (high pass

1 is effective for low compression rates, and 2

! You can also switch the equalizer by pressing

filter). Only frequencies higher than those in the

is effective for high compression rates.

FADER (fader adjustment)

repeatedly.

selected range are output from the front or rear

speakers.

LOUDNESS (loudness)

1 Press M.C. to display the setting mode.

1 Press M.C. to display the setting mode.

Function settings

2 Turn M.C. to adjust the front/rear speaker bal-

Loudness compensates for deficiencies in the low-

2 Press M.C. to cycle between the following:

1 Press M.C. to display the main menu.

ance.

frequency and high-frequency ranges at low vol-

Cut-off frequency—Slope level

ume.

3 Turn M.C. to select the desired setting.

BALANCE (balance adjustment)

2 Turn M.C. to change the menu option

1 Press M.C. to select the desired setting.

Cut-off frequency: OFF—50HZ—63HZ—80HZ

and press to select FUNCTION.

OFF (off)—LOW (low)—MID (mid)—HI (high)

—100HZ—125HZ—160HZ—200HZ

1 Press M.C. to display the setting mode.

Once selected, the function below can be ad-

Slope level: –6— –12

2 Turn M.C. to adjust the left/right speaker bal-

SUB.W (subwoofer on/off setting)

justed.

ance.

This unit is equipped with a subwoofer output

EQ SETTING (equalizer recall)

S.RTRV (sound retriever)

which can be turned on or off.

1 Press M.C. to select the desired setting.

Automatically enhances compressed audio and

NOR (normal phase)—REV (reverse phase)—

restores rich sound.

OFF (subwoofer off)

1 Press M.C. to select the desired setting.

For details, refer to Enhancing compressed

SUB.W CTRL (subwoofer adjustment)

audio and restoring rich sound (sound retriever)

on this page.

6

En

Section

Operating this unit

Operating this unit

02

SLA (source level adjustment)

LANGUAGE (multi-language)

Switching the dimmer setting

SP-P/O MODE (rear output and preout setting)

English

SLA (Source level adjustment) lets you adjust the

This unit can display the text information from a

You can adjust the brightness of illumination.

The rear speaker leads output and the RCA output

volume level of each source to prevent radical

compressed audio file even for information em-

of this unit can be used to connect a full-range

changes in volume when switching between sour-

bedded in English or Russian.

1 Press M.C. to display the main menu.

speaker or subwoofer. Select a suitable option for

ces.

! If the embedded language and the selected

your connection.

! Settings are based on the FM volume level,

language setting are not the same, text infor-

2 Turn M.C. to display ILLUMI and press to

1 Press M.C. to display the setting mode.

which remains unchanged.

mation may not display properly.

select.

2 Turn M.C. to select the desired setting.

! The MW/LW volume level can also be adjusted

! Some characters may not be displayed prop-

You can select any one of the options in the fol-

with this function.

erly.

3 Press M.C. to select the desired setting.

lowing list:

! When selecting FM as the source, you cannot

1 Turn M.C. to select the desired setting.

OFF (off)—ON (on)

! REAR/SUB.W – Select when there is a full-

switch to SLA.

ENG (English)—РУС (Russian)

! You can also change the dimmer setting by

range speaker connected to the rear speak-

1 Press M.C. to display the setting mode.

pressing and holding

/DIMMER.

er leads output and there is a subwoofer

CLOCK SET (setting the clock)

2 Turn M.C. to adjust the source volume.

connected to the RCA output.

Adjustment range: +4 to –4

! SUB.W/SUB.W – Select when there is a

1 Press M.C. to display the setting mode.

Initial menu

subwoofer connected directly to the rear

2 Press M.C. to select the segment of the clock

1 Press and hold SRC/OFF until the unit

speaker leads output without any auxiliary

display you wish to set.

System menu

Hour—Minute

turns off.

amp and there is a subwoofer connected

to the RCA output.

3 Turn M.C. to adjust the clock.

Important

2 Press and hold SRC/OFF until the main

! REAR/REAR – Select when there is a full-

PW SAVE (power saving) is canceled if the ve-

12H/24H (time notation)

menu appears in the display.

range speaker connected to the rear speak-

hicle battery is disconnected and will need to be

er leads output and the RCA output.

turned back on once the battery is reconnected.

1 Press M.C. to select the desired setting.

3 Turn M.C. to change the menu option

If there is a full-range speaker connected to

When PW SAVE (power saving) is off, depend-

12H (12-hour clock)—24H (24-hour clock)

and press to select INITIAL.

the rear speaker leads output and the RCA

ing on connection methods, the unit may con-

AUTO PI (auto PI seek)

output is not used, you may select either

tinue to draw power from the battery if your

4 Turn M.C. to select the initial menu func-

REAR/SUB.W or REAR/REAR.

vehicle’s ignition doesn’t have an ACC (acces-

The unit can automatically search for a different

tion.

sory) position.

station with the same programming, even during

Once selected, the following initial menu func-

preset recall.

tions can be adjusted.

System menu

1 Press M.C. to display the main menu.

1 Press M.C. to turn Auto PI seek on or off.

AUX (auxiliary input)

FM STEP (FM tuning step)

1 Press and hold SRC/OFF until the unit

2 Turn M.C. to change the menu option

turns off.

and press to select SYSTEM.

Activate this setting when using an auxiliary de-

Normally, the FM tuning step employed by seek

vice connected to this unit.

tuning is 50 kHz. When AF or TA is on, the tuning

2 Press and hold SRC/OFF until the main

3 Turn M.C. to select the system menu

1 Press M.C. to turn AUX on or off.

step automatically changes to 100 kHz. It may be

menu appears in the display.

function.

preferable to set the tuning step to 50 kHz when

PW SAVE (power saving)

Once selected, the following system menu func-

AF is on.

3 Turn M.C. to change the menu option

tions can be adjusted.

Switching this function on enables you to reduce

! The tuning step remains at 50 kHz during man-

and press to select SYSTEM.

the consumption of battery power.

ual tuning.

! Turning on the source is the only operation al-

1 Press M.C. to select the FM tuning step.

4 Turn M.C. to select the system menu

lowed when this function is on.

50 (50 kHz)—100 (100 kHz)

function.

1 Press M.C. to turn the power save on or off.

Once selected, the following system menu func-

tions can be adjusted.

For details, refer to System menu on this page.

En

7

Using an AUX source

Connections

— Never wire the negative speaker cable directly

to ground.

1 Insert the stereo mini plug into the AUX

Important

— Never band together negative cables of multi-

input jack.

! When installing this unit in a vehicle without

ple speakers.

an ACC (accessory) position on the ignition

! When this unit is on, control signals are sent

2 Press SRC/OFF to select AUX as the

switch, failure to connect the red cable to the

through the blue/white cable. Connect this

source.

terminal that detects operation of the ignition

cable to the system remote control of an ex-

key may result in battery drain.

ternal power amp or the vehicle’s auto-anten-

Note

na relay control terminal (max. 300 mA

AUX cannot be selected unless the auxiliary set-

F

F

O

N

12 V DC). If the vehicle is equipped with a

ting is turned on. For more details, refer to AUX

O

S

A

T

glass antenna, connect it to the antenna

(auxiliary input) on the previous page.

T

R

booster power supply terminal.

! Never connect the blue/white cable to the

ACC position No ACC position

Switching the display

power terminal of an external power amp.

! Use of this unit in conditions other than the

Also, never connect it to the power terminal

Selecting the desired text information

following could result in fire or malfunction.

of the auto antenna. Doing so may result in

1 Press DISP to cycle between the following:

— Vehicles with a 12-volt battery and negative

battery drain or a malfunction.

! Source name

grounding.

! The black cable is ground. Ground cables for

! Source name and clock

— Speakers with 50 W (output value) and 4 W to

this unit and other equipment (especially,

8 W (impedance value).

high-current products such as power amps)

! To prevent a short-circuit, overheating or mal-

must be wired separately. If they are not, an

If an unwanted display appears

function, be sure to follow the directions

accidental detachment may result in a fire or

below.

malfunction.

Turn off the unwanted display using the proce-

— Disconnect the negative terminal of the bat-

dures listed below.

tery before installation.

This unit

— Secure the wiring with cable clamps or adhe-

1 Press M.C. to display the main menu.

sive tape. Wrap adhesive tape around wiring

that comes into contact with metal parts to

2 Turn M.C. to change the menu option

protect the wiring.

and press to select SYSTEM.

— Place all cables away from moving parts,

such as the shift lever and seat rails.

3 Turn M.C. to display DEMO OFF and press

— Place all cables away from hot places, such

to select.

as near the heater outlet.

— Do not connect the yellow cable to the battery

4 Turn M.C. to switch to YES.

by passing it through the hole to the engine

compartment.

5 Press M.C. to select.

— Cover any disconnected cable connectors

with insulating tape.

— Do not shorten any cables.

— Never cut the insulation of the power cable of

this unit in order to share the power with

other devices. The current capacity of the

cable is limited.

— Use a fuse of the rating prescribed.

3 4

Section

02

Operating this unit

Installation

03

21

1 Power cord input

2 Rear output or subwoofer output

3 Antenna input

4 Fuse (10 A)

8

En

Power cord

3

4

2

5

6

1

3

4

7

5

6

8

a

9

b

d

c

9 Blue/white

Power amp (sold separately)

! When installing, to ensure proper heat dis-

The pin position of the ISO connector will dif-

persal when using this unit, make sure you

Perform these connections when using the op-

fer depending on the type of vehicle. Connect

leave ample space behind the rear panel and

tional amplifier.

9 and b when Pin 5 is an antenna control

wrap any loose cables so they are not block-

type. In another type of vehicle, never con-

1

3

ing the vents.

nect 9 and b.

2

a Blue/white





4

Connect to system control terminal of the

55





power amp (max. 300 mA 12 V DC).

b Blue/white

1 System remote control

Connect to auto-antenna relay control termi-

Connect to Blue/white cable.

nal (max. 300 mA 12 V DC).

2 Power amp (sold separately)

c Speaker leads

3 Connect with RCA cables (sold separately)

White: Front left +

4 To Rear output or subwoofer output

White/black: Front left *

5 Rear speaker or subwoofer

Gray: Front right +

Gray/black: Front right *

Green: Rear left + or subwoofer +

Installation

Green/black: Rear left * or subwoofer *

Violet: Rear right + or subwoofer +

Important

Violet/black: Rear right * or subwoofer *

! Check all connections and systems before

1 To power cord input

d ISO connector

final installation.

2 Depending on the kind of vehicle, the func-

In some vehicles, the ISO connector may be

! Do not use unauthorized parts as this may

tion of 3 and 5 may be different. In this

divided into two. In this case, be sure to con-

cause malfunctions.

case, be sure to connect 4 to 5 and 6 to

nect to both connectors.

! Consult your dealer if installation requires

3.

drilling of holes or other modifications to the

Notes

3 Yellow

vehicle.

Back-up (or accessory)

! Change the initial menu of this unit. Refer to

! Do not install this unit where:

4 Yellow

SP-P/O MODE (rear output and preout set-

— it may interfere with operation of the vehicle.

Connect to the constant 12 V supply termi-

ting) on page 7.

— it may cause injury to a passenger as a result

nal.

The subwoofer output of this unit is monau-

of a sudden stop.

5 Red

ral.

! The semiconductor laser will be damaged if

Accessory (or back-up)

! When using a subwoofer of 70 W (2 W), be

it overheats. Install this unit away from hot

6 Red

sure to connect the subwoofer to the violet

places such as near the heater outlet.

Connect to terminal controlled by ignition

and violet/black leads of this unit. Do not

! Optimum performance is obtained when the

switch (12 V DC).

connect anything to the green and green/

unit is installed at an angle of less than 60°.

7 Connect leads of the same color to each

black leads.

other.

60°

8 Black (chassis ground)

5cmcm

Section

Installation

Installation

03

English

Leave ample

space

5 cm

5 cm

DIN front/rear mount

This unit can be properly installed using either

front-mount or rear-mount installation.

Use commercially available parts when instal-

ling.

DIN Front-mount

1 Insert the mounting sleeve into the dash-

board.

For installation in shallow spaces, use the sup-

plied mounting sleeve. If there is enough space,

use the mounting sleeve that came with the ve-

hicle.

2 Secure the mounting sleeve by using a

screwdriver to bend the metal tabs (90°) into

place.

1

2

1 Dashboard

En

9

Section

03

Installation

Additional information

2 Mounting sleeve

! When reattaching the trim ring, point the

Troubleshooting

Error messages

# Make sure that the unit is installed securely in

side with the notched tab down.

place. An unstable installation may cause skipping

When you contact your dealer or your nearest

or other malfunctions.

2 Insert the supplied extraction keys into

Symptom Cause Action

Pioneer Service Center, be sure to note the error

both sides of the unit until they click into

message.

The display

You did not per-

Perform operation

place.

DIN Rear-mount

automatically

form any opera-

again.

returns to the

tion within

Common

1 Determine the appropriate position

3 Pull the unit out of the dashboard.

ordinary dis-

about 30 sec-

where the holes on the bracket and the side

Message Cause Action

play.

onds.

of the unit match.

AMP ERROR Unit fails to op-

Check the speak-

The repeat

Depending on

Select the repeat

erate or speaker

er connection. If

play range

the repeat play

play range again.

connection is

the message fails

changes un-

range, the se-

incorrect; pro-

to disappear even

expectedly.

lected range

tective circuit is

after the engine is

may change

activated.

switched off/on,

when another

contact your deal-

2 Tighten two screws on each side.

Removing and re-attaching the front

folder or track is

er or an author-

panel

being selected

ized Pioneer

You can remove the front panel to protect your

or during fast

3

Service Station

1

unit from theft.

forwarding/re-

for assistance.

Press the detach button and push the front

versing.

panel upward and pull it toward you.

A subfolder is

Subfolders can-

Select another re-

2

For details, refer to Removing the front panel to

not played

not be played

peat play range.

USB storage device

protect your unit from theft and Re-attaching the

back.

when FLD (fold-

Message Cause Action

1 Tapping screw (5 mm × 8 mm)

front panel on page 3.

er repeat) is se-

2 Mounting bracket

lected.

FORMAT

Sometimes

Wait until the

3 Dashboard or console

NO XXXX ap-

There is no em-

Switch the display

READ

there is a delay

message disap-

pears when a

bedded text in-

or play another

between the

pears and you

Removing the unit

display is

formation.

track/file.

start of playback

hear sound.

changed (NO

and when you

1 Remove the trim ring.

TITLE, for ex-

start to hear any

ample).

sound.

The unit is

You are using a

Move electrical

NO AUDIO There are no

Transfer the audio

malfunction-

device, such as

devices that may

songs.

files to the USB

ing.

a cellular

be causing the in-

storage device

There is inter-

phone, that

terference away

and connect.

ference.

transmits elec-

from the unit.

The connected

Follow the USB

tric waves near

USB storage de-

storage device in-

1 Trim ring

the unit.

vice has secur-

structions to dis-

2 Notched tab

ity enabled.

able the security.

! Releasing the front panel allows easier ac-

cess to the trim ring.

10

En

Appendix

Additional information

Additional information

WAV

Message Cause Action

Message Cause Action

Firmly secure the USB storage device when driv-

English

ing. Do not let the USB storage device fall onto the

SKIPPED The connected

Play an audio file

ERROR-19 Communication

Perform one of

floor, where it may become jammed under the

File extension: .wav

USB storage de-

not embedded

failed.

the following op-

brake or accelerator pedal.

Quantization bits: 8 and 16 (LPCM), 4 (MS

vice contains

with Windows

erations.

ADPCM)

files embedded

Media DRM 9/10.

–Turn the ignition

Depending on the USB storage device, the follow-

with Windows

switch OFF and

ing problems may occur.

Sampling frequency: 16 kHz to 48 kHz (LPCM),

Mediaä DRM 9/

back ON.

! Operations may vary.

22.05 kHz and 44.1 kHz (MS ADPCM)

10.

–Disconnect the

! The storage device may not be recognized.

! Files may not be played back properly.

PROTECT All the files in

Transfer audio

USB storage de-

vice.

! The device may generate noise in the radio.

Supplemental information

the USB storage

files not em-

device are em-

bedded with

–Change to a dif-

ferent source.

Only the first 32 characters can be displayed as a

bedded with

Windows Media

Windows Media

Then, return to

file name (including the file extension) or a folder

DRM 9/10 to the

Compressed audio

USB storage de-

the USB source.

name.

DRM 9/10.

compatibility (USB)

vice and connect.

ERROR-23 USB storage de-

USB storage de-

Russian text to be displayed on this unit should be

WMA

N/A USB The USB device

! Connect a USB

vice was not for-

vice should be for-

encoded in one of the following character sets:

connected to is

Mass Storage

matted with

matted with

! Unicode (UTF-8, UTF-16)

not supported

Class compliant

FAT12, FAT16 or

FAT12, FAT16 or

File extension: .wma

! A character set other than Unicode that is

by this unit.

device.

FAT32.

FAT32.

used in a Windows environment and is set to

Bit rate: 48 kbps to 320 kbps (CBR), 48 kbps to

Russian in the multi-language setting

! Disconnect

STOP There are no

Select a list that

384 kbps (VBR)

your device and

songs in the

contains songs.

This unit may not operate correctly depending on

Sampling frequency: 32 kHz, 44.1 kHz, 48 kHz

replace it with a

current list.

the application used to encode WMA files.

compatible USB

Windows Media Audio Professional, Lossless,

There may be a slight delay at the start of playback

storage device.

Voice/DRM Stream/Stream with video: Not com-

of audio files embedded with image data or audio

CHECK USB The USB con-

Check that the

Handling guidelines

patible

files stored on a USB storage device that has nu-

nector or USB

USB connector or

USB storage device

merous folder hierarchies.

cable has short-

USB cable is not

MP3

circuited.

caught in some-

Address any questions you have about your USB

thing or dam-

USB storage device

storage device to the manufacturer of the device.

File extension: .mp3

aged.

The connected

Disconnect the

Connections via USB hub are not supported.

Bit rate: 8 kbps to 320 kbps (CBR), VBR

Playable folder hierarchy: up to eight tiers (A prac-

USB storage de-

USB storage de-

tical hierarchy is less than two tiers.)

Do not connect anything other than a USB stor-

Sampling frequency: 8 kHz to 48 kHz (32 kHz,

vice consumes

vice and do not

age device.

44.1 kHz, 48 kHz for emphasis)

Playable folders: up to 500

more than maxi-

use it. Turn the

mum allowable

ignition switch to

Compatible ID3 tag version: 1.0, 1.1, 2.2, 2.3, 2.4

Playable files: up to 15 000

current.

OFF, then to ACC

(ID3 tag Version 2.x is given priority over Version

Playback of copyright-protected files: Not compati-

or ON and then

1.x.)

ble

connect only

M3u playlist: Not compatible

compliant USB

storage devices.

MP3i (MP3 interactive), mp3 PRO: Not compatible

En

11

Appendix

Additional information

Additional information

3 Save the folder containing files on the USB

streaming via internet, intranets and/or other

Partitioned USB storage device: Only the first par-

Specifications

storage device.

networks or in other electronic content distribu-

tition can be played.

However, depending on the system environment,

tion systems, such as pay-audio or audio-on-de-

General

There may be a slight delay when starting play-

you may not be able to specify the playback se-

mand applications. An independent license for

Power so urce ………………. 14.4 V DC (10.8 V to 15.1 V al-

back of audio files on a USB storage device with

lowable)

quence.

such use is required. For details, please visit

Grounding system ………… Negative type

numerous folder hierarchies.

For USB portable audio players, the sequence is

http://www.mp3licensing.com.

Maximum current consumption

different and depends on the player.

…………………………….. 10.0 A

WMA

Dimensions (W × H × D):

CAUTION

Windows Media is either a registered trademark

DIN

Russian character chart

Chassis ………….. 178mm × 50 mm ×

! Pioneer cannot guarantee compatibility with

or trademark of Microsoft Corporation in the

165 mm

all USB mass storage devices and assumes

United States and/or other countries.

Nose ……………… 188 mm × 58 mm ×

no responsibility for any loss of data on

D: C D: C D: C D: C D: C

This product includes technology owned by

15 mm

media players, smart phones, or other devi-

: А : Б : В : Г : Д

Microsoft Corporation and cannot be used or

D

ces while using this product.

distributed without a license from Microsoft

Chassis ………….. 178mm × 50 mm ×

! Do not leave a USB storage device in any

: Е, Ё : Ж : З : И, Й : К

Licensing, Inc.

165 mm

Nose ……………… 170 mm × 46 mm ×

place that is subject to high temperatures.

: Л : М : Н : О : П

15 mm

: Р : С : Т : У : Ф

Weight ……………………….. 0.7 kg

Sequence of audio files

: Ш,

: Х : Ц : Ч

: Ъ

Audio

The user cannot assign folder numbers and

Щ

Maximum power output ... 50 W × 4

specify playback sequences with this unit.

: Ы : Ь : Э : Ю : Я

70 W × 1/2 W (for subwoofer)

Continuous power output

Example of a hierarchy

D: Display C: Character

…………………………….. 22 W × 4 (50 Hz to 15 000Hz,

01

5 % THD, 4 W load, both chan-

02

nels driven)



Load impedance ………….. 4 W (4 W to 8 W allowable)



Copyright and trademark

Preout maximum output level

: Folder

03

…………………………….. 2.0V

: Compressed



iTunes

Loudness contour ………… +10dB (100 Hz), +6.5 dB

04



audio file

Apple and iTunes are trademarks of Apple Inc.,

(10 kHz) (volume: –30 dB)



01 to 05: Folder

registered in the U.S. and other countries.

Equalizer (5-Band Graphic Equalizer):



number

Frequency …………….. 80 Hz/250 Hz/800 Hz/

05

1 to 6: Playback

2.5 kHz/8 kHz

MP3

Level 1 Level 2 Level 3 Level 4

sequence

Equalization range …. ±12 dB (2 dB step)

Supply of this product only conveys a license for

Subwoofer (mono):

private, non-commercial use and does not con-

Frequency …………….. 50 Hz/63 Hz/80 Hz/100 Hz/

USB storage device

vey a license nor imply any right to use this prod-

125 Hz/160 Hz/200 Hz

Playback sequence is the same as recorded se-

uct in any commercial (i.e. revenue-generating)

Slope …………………… –6 dB/oct, –12 dB/oct

Gain ……………………. +6 dB to –24 dB

quence in the USB storage device.

real time broadcasting (terrestrial, satellite,

Phase ………………….. Normal/Reverse

To specify the playback sequence, the following

cable and/or any other media), broadcasting/

method is recommended.

1 Create a file name that includes numbers

USB

that specify the playback sequence (e.g.,

USB standard specification

…………………………….. USB 2.0 full speed

001xxx.mp3 and 099yyy.mp3).

2 Put those files into a folder.

12

En