Sharp 5316 сервис мануал

Download Sharp AR-5316. Service Manual

Все материалы на сайте представлены исключительно для ознакомления. Все торговые марки и права на публикуемые материалы принадлежат их владельцам.

All materials on the site are presented solely for information. All trademarks and copyrights in the published materials belong to their respective owners.

• Драйверы
  
  3
  

• Руководства по ремонту
  
  1
  

Sharp AR-5316 (Принтеры) сервис мануалы в PDF-формате помогут найти неполадки и ошибки, а также осуществить ремонт Sharp AR-5316 и восстановить работу устройства.

• 19, COPYRIGHT 2003 BY SHARP CORPORATION All rights reserved. Printed in Japan. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. Trademark acknowledgments Windows and Windows NT are trademarks of Microsoft Corporat…

• 9, AR-5316/5320 SIMULATIONS 7-3 06 02 Resist roller solenoid operation check When the [START] key is pressed in the sub code input state, the resist solenoid (RRS) turns ON for 500ms and OFF for 500ms. This operation is repeated 20 times. After completion of the process, the machine goes into the sub code input standby mode. When [INTERRUPT] key is pressed during the process, t…

• 4, AR-5316/5320 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4-1 [4] EXTERNAL VIEWS AND INTERNAL STRUCTURES 1. Appearance 2. Internal 1 Document feeder cover (when the SPF is installed) /document cover 2 Document glass 3 Handles 4 Power switch 5 Operation panel 6 Paper output tray 7 Front cover 8 Paper trays 9 Side cover 10 Side cover handle 11 Bypass tray guides 12 Bypa…

• 6, AR-5316/5320 UNPACKING AND INSTALLATION 5-1 [5]UNPACKING AND INSTALLATION 5. Changing a tray’s paper size setting Follow these steps to change a tray’s paper size setting. Note: •The paper size setting cannot be changed when the machine has stopped temporarily due to running out of paper or a misfeed, or during interrupt copying. •During printing (even in copy mode), the pape…

• 13, AR-5316/5320 USER PROGRAMS 8-2 Program name Program No Description Default Parameters Key auto repeat 25 Use this setting to select whether or not holding down a key causes repeated input of the key. For keys that normally cause a set value to increase when held down (for example, holding down the [ZOOM] key), this program can be used to have the set value not change when the key i…

• 10, AR-5316/5320 SIMULATIONS 7-4 22 22 SPF jam counter display The SPF jam counter value is displayed. (Alternate display by 3 digits)When the [Interrupt] key is pressed, the machine goes into the sub code input standby mode. When the [CA] key is pressed, the simulation is terminated. 44 34 Transfer current setting Used to set the transfer current for the front surface and that for the b…

• 3, AR-5316/5320 CONSUMABLE PARTS 3-1 [3] CONSUMABLE PARTS 1. Supply system table A. East Europe / Russia Note 1: The individual carton is printed with English, German, French, and Spanish as well as the green mark. B. Middle East / Africa / Philippine Note 1: The individual carton is printed with English, German, French, and Spanish as well as the green mark. C. Asia Note 1: The indivi…

• 2, AR-5316/5320 NOTE FOR THIS SERVICE MANUAL 1-1 [1] NOTE FOR THIS SERVICE MANUAL This Service Manual describes only the items related to the AR-5316 and AR-5320. For the other items common with the AR-M160/M205, please refer to the AR-M160/205 Service Manual (Document code:00ZARM205/A1E). The table below shows which document(s) should be referred to for each sect…

• 17, AR-5316/5320 ELECTRICAL SECTION 13-2 3. Actual wiring diagram ACTUAL WIRING DIAGRAM 1/7 B03P-VL (WHITE) B4B-PH-K-BL (BLACK) SPF GROUND WIRE ORIGINAL TRAY HARNESS SENSOR HARNESS 04FE-BT-VK-N (WHITE) B3B-PH-K-R (RED) Mirror HP SENSOR OPTICAL BASE PLATE CCD PWB Mirror MOTOR COPY LAMP THERMISTER Side Cover SW MAIN MOTOR TONER MOTOR DEV UN POWER PWB MCU-PWB HAND PAPER PICK UP SOLENOID HA…

• 8, AR-5316/5320 SIMULATIONS 7-2 4. Contents of simulations 50 01 Image lead edge adjustment 06 Copy lead edge position adjustment (SPF/RSPF) 10 Paper off-center adjustment 12 Document off-center adjustment 51 02 Resist amount adjustment 53 08 SPF scanning position automatic adjustment 10 SPF scan position change-over setting 61 03 HSYNC output check 63 01 Shading check…

• 5, AR-5316/5320 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4-2 3. Operation Section 1 ON LINE key/indicator 2 DUAL PAGE COPY key/indicator 3 XY-ZOOM key/indicator 4 SPF indicator (when the SPF is installed) 5 Paper feed location / misfeed location indicators 6 ORIGINAL SIZE ENTER key / ORIGINAL SIZE indicators 7 PAPER SIZE indicators 8 PRESET RATIO selector keys / indicators 9 AUTO/TEXT/PHOTO key / …

• 15, AR-5316/5320 MAINTENANCE 10-2 2. Maintenance display system *1: Installation of a new toner cartridge allows to display the remaining quantity. 3. Note for replacement of consumable parts A. Toner cartridge When a waste toner cartridge is removed from the machine, it must be put in a polyethylene bag to avoid scattering of toner. B. DV cartridge Do not shake or put up …

• 16, AR-5316/5320 ELECTRICAL SECTION 13-1 [13] ELECTRICAL SECTION 1. Block diagram Scanner Unit CCD PWB 5V A5V 3.3V B/W 8bits(MSB/LSB) 5V ADCCLK,SYNCH, BSAMP,VSAMP SDI,SCLK,LOAD,OBE MODE LVTTL MCU-PWB 3.3V IEEE 1284 I/F USB I/F Printer CLK(20.3094MHz) 3.3V RIC Download Scanner CLK(48MHz) A[19 … 1] D[15 … 0] 1Mb(1Mb*1) 8Mbit I2C Bus 4Kbyte Other Loads MPFS,RRS, SGS,SRRC,SPUS,SPPS, Toner MotorMain Mo…

• 14, AR-5316/5320 MAINTENANCE 10-1 [10] MAINTENANCE 1. Maintenance table X:Check(Clean, adjust, or replace when required.) O:Clean :Replace :Adjust :Lubricate *1:Recommendable replacement time:50K(Letter,5%print) Unit name Part name When calling 50K 100K 150K Drum peripheral OPC drum — Cleaning blade — Side seal F/R X X X X MC unit X (MC charging electrode) — ( ) ( ) ( ) (MC grid) — () () () (MC …

• This document has been published to be used forafter sales
  service only.The contents are subject to change without notice.

  Parts marked with are important for maintaining the safety of
  the set. Be sure to replace these parts with specified ones for
  maintaining the safety and performance of the set.

  SHARP CORPORATION

  DIGITAL COPIERAR-5316

  MODEL AR-5320

  CODE : 00ZAR5320/A1E

  AR-5316

  AR-5320(with option installed)

  [ 1 ] NOTE FOR THIS SERVICE MANUAL . . . . . . . . . . . . . .
  .Refer to AR-M160[ 2 ] SPECIFICATIONS. . . . . . . . . . . . . . .
  . . . . . . . . . . . . . . . . . . .AR-5316/5320[ 3 ] CONSUMABLE
  PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
  .AR-5316/5320[ 4 ] EXTERNAL VIEWS AND INTERNAL STRUCTURES . . . . .
  .AR-5316/5320[ 5 ] UNPACKING AND INSTALLATION . . . . . . . . . . .
  . . . . . . . . . .AR-5316/5320[ 6 ] ADJUSTMENTS . . . . . . . . .
  . . . . . . . . . . . . . . . . . . . . . . .Refer to AR-M160[ 7 ]
  SIMULATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . .
  . . . . . . . .AR-5316/5320[ 8 ] USER PROGRAMS . . . . . . . . . .
  . . . . . . . . . . . . . . . . . . . . . .AR-5316/5320[ 9 ]
  TROUBLE CODE LIST . . . . . . . . . . . . . . . . . . . . . . . . .
  . .Refer to AR-M160[10] MAINTENANCE . . . . . . . . . . . . . . . .
  . . . . . . . . . . . . . . . . . . .AR-5316/5320[11] DISASSEMBLY
  AND ASSEMBLY . . . . . . . . . . . . . . . . . . .Refer to
  AR-M160[12] FLASH ROM VERSION UP PROCEDURE . . . . . . . . . .
  .Refer to AR-M160[13] ELECTRICAL SECTION . . . . . . . . . . . . .
  . . . . . . . . . . . . . . . .AR-5316/5320

  CONTENTS

  [00]COVER.fm 1

  www.

  tehran

  copy

  .com

• AR-5316/5320 NOTE FOR THIS SERVICE MANUAL 1-1

  [1] NOTE FOR THIS SERVICE MANUALThis Service Manual describes
  only the items related to the AR-5316 and AR-5320. For the other
  items common with the AR-M160/M205, please referto the AR-M160/205
  Service Manual (Document code:00ZARM205/A1E). The table below shows
  which document(s) should be referred to for eachsection. (Refer to
  the document marked with O.)

  [2] SPECIFICATIONSThe table below shows the specifications of
  this model and the contents of changes from the AR-M160/M205 and
  AR-5316/5320.

  Option

  O : The option can be installed. — : The option cannot be
  installed.

  Section AR-M160/M205 AR-5316/AR-5320 Changed item[ 1 ] GENERAL
  O[ 2 ] SPECIFICATIONS O O Some specifications[ 3 ] CONSUMABLE PARTS
  O[ 4 ] EXTERNAL VIEWS AND INTERNAL STRUCTURES O O Appearance /
  Internal / Operation panel[ 5 ] UNPACKING AND INSTALLATION O O
  Changing the copy paper size in the tray[ 6 ] ADJUSTMENTS O[ 7 ]
  SIMULATIONS O O Shifter sensors status display, etc. deleted.[ 8 ]
  USER PROGRAMS O O USB2.0 mode switch, etc. deleted.[ 9 ] TROUBLE
  CODE LIST O[10] MAINTENANCE O[11] DISASSEMBLY AND ASSEMBLY O[12]
  FLASH ROM VERSION UP PROCEDURE O[13] ELECTRICAL SECTION O O Block
  diagram / Actual wiring diagram 1/7

  Item AR-M160 AR-5316 AR-M205 AR-5320Paper feed system 1cassette
  +

  Multi manual paper feedOne automatic feeding paper

  tray(250sheets) + bypass tray(100sheets)

  2cassette + Multi manual paper feed

  Two automatic feeding paper trays(250sheets each) + bypass
  tray(100sheets)

  Weight Approx.31.3Kg Approx.31.3Kg(Not including TD
  cartridge)

  Approx.35.1Kg Approx.36.3Kg(Not including TD cartridge)

  Interface USB1.1/USB2.0IEEE1284

  IEEE1284parallel connector/USB1.1

  USB1.1/USB2.0IEEE1284

  IEEE1284parallel connector/USB1.1

  Machine Model AR-M160 AR-M205 AR-5316 AR-5320 Remark250 sheets
  paper feed unit AR-D24 / D25 O O — -SPF AR-SP6 O — O ORSPF AR-RP6 —
  O — -Original cover AR-VR5 Standard O Standard Standard

  [01_02]NOTE_SPEC.fm 1

  www.

  tehran

  copy

  .com

• AR-5316/5320 CONSUMABLE PARTS 3-1

  [3] CONSUMABLE PARTS1. Supply system tableA. East Europe /
  Russia

  Note 1: The individual carton is printed with English, German,
  French, and Spanish as well as the green mark. B. Middle East /
  Africa / Philippine

  Note 1: The individual carton is printed with English, German,
  French, and Spanish as well as the green mark. C. Asia

  Note 1: The individual carton is printed with English, German,
  French, and Spanish as well as the green mark. D. Hong Kong

  Note 1: The individual carton is printed with English and
  Chinese as well as the green mark.

  NO Name Content Life Product name Remark1 Toner
  cartridge(Black)

  Toner(Toner: Net Weight 537g)Vinyl bag

  x10

  x10

  160K AR-016LT Life setting by A4 6% documentLT=T*10

  2 Developer Developer(Developer : Net Weight 400g)

  x10 500K AR-202LD LD=DV*10

  3 Drum kit DrumDrum fixing plate

  x1x1

  50K AR-202DM

  NO Name Content Life Product name Remark1 Toner
  cartridge(Black)

  Toner(Toner: Net Weight 537g)Vinyl bag

  x10

  x10

  190K AR-016ET Life setting by A4 6% documentET=FT*10

  2 Developer Developer(Developer : Net Weight 400g)

  x10 500K AR-202CD CD=SD*10

  3 Drum kit DrumDrum fixing plate

  x1x1

  50K AR-202DR

  NO Name Content Life Product name Remark1 Toner
  cartridge(Black)

  Toner(Toner: Net Weight 537g)Vinyl bag

  x10

  x10

  190K AR-016CT Life setting by A4 6% documentCT=ST*10

  2 Developer Developer(Developer : Net Weight 400g)

  x10 500K AR-202CD CD=SD*10

  3 Drum kit DrumDrum fixing plate

  x1x1

  50K AR-202DR

  NO Name Content Life Product name Remark1 Toner
  cartridge(Black)

  Toner(Toner: Net Weight 537g)Vinyl bag

  x10

  x10

  190K AR-016CT-C Life setting by A4 6% documentCT-C=ST-C*10

  2 Developer Developer(Developer : Net Weight 400g)

  x10 500K AR-202CD-C CD-C=SD-C*10

  3 Drum kit DrumDrum fixing plate

  x1x1

  50K AR-202DR-C

  [03]CONSUMABLEPARTS.fm 1

  www.

  tehran

  copy

  .com

• AR-5316/5320 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4-1

  [4] EXTERNAL VIEWS AND INTERNAL STRUCTURES1. Appearance

  2. Internal

  1 Document feeder cover (when the SPF is installed) /document
  cover

  2 Document glass 3 Handles

  4 Power switch 5 Operation panel 6 Paper output tray7 Front
  cover 8 Paper trays 9 Side cover

  10 Side cover handle 11 Bypass tray guides 12 Bypass tray13
  Bypass tray extension 14 Charger cleaner 15 USB 1.1 connector16
  Parallel connector

  17 Document feeder tray (when the SPF is installed)

  18 Original guides (when the SPF is installed)

  19 Feeding roller cover (when the SPF is installed)

  20 Right side cover (when the SPF is installed)

  21 Exit area (when the SPF is installed)

  22 Toner cartridge lock release lever

  23 Toner cartridge 24 Roller rotating knob 25 Fusing unit
  release levers26 Photoconductive drum 27 Fusing unit paper
  guide

  1

  1

  3

  9

  10

  131211

  6 5

  2

  3

  74

  16

  14

  15

  8

  1917

  22

  23

  2120

  24 25

  18

  2726

  [04]EXTERNALVIEWS.fm 1

  www.

  tehran

  copy

  .com

• AR-5316/5320 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4-2

  3. Operation Section

  1 ON LINE key/indicator 2 DUAL PAGE COPY key/indicator 3 XY-ZOOM
  key/indicator4 SPF indicator

  (when the SPF is installed)5 Paper feed location / misfeed
  location

  indicators6 ORIGINAL SIZE ENTER key /

  ORIGINAL SIZE indicators7 PAPER SIZE indicators 8 PRESET RATIO
  selector keys /

  indicators

  9 AUTO/TEXT/PHOTO key / indicators 10 AUDIT CLEAR key 11 AUTO
  PAPER SELECT indicator12 Alarm indicators 13 POWER SAVE indicator
  14 Display15 Copy ratio display key 16 ZOOM indicator 17 Zoom
  keys18 INTERRUPT key / indicator 19 Light and Dark keys /
  indicators 20 PAPER SIZE ENTER key21 TRAY SELECT key 22 AUTO IMAGE
  key / indicator 23 Numeric keys24 # key 25 START key / indicator 26
  CLEAR ALL key27 CLEAR key

  The example of a display of inch series200%

  50%

  141

  957764

  129121

  11X178X148X11

  8X118X5

  EXTRA8X13

  100%

  AR-5316/AR-5316X

  4 5

  The indications of the operation panel may differ depending on
  the country and the region.

  4 5 86 7

  2 31

  INTERRUPTZOOM

  1 3 5

  25 400%

  AUTO

  ENTER

  AUTOACC.#-C

  AUTO %

  A3A4A4A5B4

  EXTRA

  200%

  50%

  141

  868170

  122115100%

  15 16 179 1011

  12 13 14

  23 25 2624 27

  18

  819 6 7 20 4 21 22 5

  Not used for this machine.

  [04]EXTERNALVIEWS.fm 2

  www.

  tehran

  copy

  .com

• AR-5316/5320 UNPACKING AND INSTALLATION 5-1

  [5]UNPACKING AND INSTALLATION5. Changing a tray’s paper size
  settingFollow these steps to change a tray’s paper size
  setting.

  Note:The paper size setting cannot be changed when the machine
  hasstopped temporarily due to running out of paper or a misfeed, or
  duringinterrupt copying.

  During printing (even in copy mode), the paper size setting
  cannot bechanged.

  A5 size paper can only be selected in upper paper tray.Do not
  load paper that is a different size than the paper size
  setting.Copying will not be possible.

  1) Hold down the [PAPER SIZE ENTER] key for more than 5 seconds
  toset the selected paper size.The currently selected paper feed
  location indicator will blink and thecorresponding paper size
  (which is currently set) indicator will lightsteadily.All other
  indicators will go out.

  2) If the machine has two paper trays, use the [TRAY SELECT] key
  toselect the paper tray for which you wish to change the paper
  sizesetting.Each time the [TRAY SELECT] key is pressed, a paper
  tray will beindicated with a blinking paper feed location
  indicator.

  3) Use the [ORIGINAL SIZE ENTER] key to select the paper
  size.The indicator of the selected paper size lights up.

  4) Squeeze the lock lever of the front guide and slide the front
  guide tomatch the width of the paper, and move the left guide to
  theappropriate slot as marked on the tray.

  The front guide is a slide-type guide. Grasp the locking knob on
  theguide and slide the guide to the indicator line of the paper to
  be loaded.

  The left guide is an insert-type guide. Remove it and then
  insert it at theindicator line of the paper to be loaded.

  When using 11″ x 17″ sized paper store the left guide in the
  slot at theleft front of the paper tray.

  5) Press the [START] key and then the [PAPER SIZE ENTER] key.To
  change the paper size setting of another tray, repeat steps 2) to
  5)after pressing the [START] key.

  Note:Affix the paper size label for the paper size selected in
  step 3) tothe label position on the right end of the tray.

  Important points when using the printer modeMake sure that the
  tray’s paper size setting is the same as the tray’spaper size
  setting in the printer driver. For example, if the tray’s papersize
  setting is A4R, set «Setting Paper Size» to «A4-R». For
  moreinformation, see «CONFIGURING THE PRINTER DRIVER» in
  the»Software Setup Guide».

  A3A4A4A5B4

  XTRA

  ENTERA3A4A4A5B4TRA

  Left guide

  Front guide

  [05]UNPACKING.fm 1

  www.

  tehran

  copy

  .com

• AR-5316/5320 SIMULATIONS 7-1

  [7] SIMULATIONS1. Entering the simulation modePerform the
  following procedure to enter the simulation mode.»#» key Interrupt
  key «C» key Interrupt key Main code Start key Sub code Start
  key

  2. Canceling the simulation modeWhen the clear all key is
  pressed, the simulation mode is cancelled.When the interruption key
  is pressed, the process is interrupted and thescreen returns to the
  sub code entering display.* After canceling the simulation mode, be
  sure to turn OFF/ON the

  power and check the operation.

  Note: If the machine is terminated by a jam error or paper empty
  duringcopying in the adjustment by the simulation, recopying is
  required.

  3. List of simulationsMain code

  Sub code Contents

  01 01 Mirror scanning operation02 Mirror home position sensor
  (MHPS) status display06 Mirror scanning operation aging

  02 01 Single paper feeder (SPF) aging02 SPF sensor status
  display03 SPF motor operation check08 SPG paper feed solenoid
  operation check 11 SPF PS release solenoid operation check

  05 01 Operation panel display check 02 Fusing lamp and cooling
  fan operation check 03 Copy lamp lighting check

  06 01 Paper feed solenoid operation check 02 Resist roller
  solenoid operation check10 Cassette semi-circular roller
  cleaning

  07 01 Warm-up display and aging with jam06 Intermittent aging08
  Shifting with warm-up display

  08 01 Developing bias output02 Main charger output (Grid =
  HIGH)03 Main charger output (Grid = LOW)06 Transfer charger
  output

  10 — Toner motor operation 14 — Trouble cancel (except for U2)
  16 — U2 trouble cancel20 01 Maintenance counter clear21 01
  Maintenance cycle setting

  02 Mini maintenance cycle setting22 01 Maintenance counter
  display

  02 Maintenance preset display03 Jam memory display04 Jam total
  counter display05 Total counter display06 Developing counter
  display07 Mini maintenance preset display08 SPF counter display 09
  Paper feed counter display12 Drum counter display13 CRUM type
  display14 P-ROM version display

  22 15 Trouble memory display17 Copy counter display18 Printer
  counter display21 Scanner counter display22 SPF jam counter
  display

  24 01 Jam total counter clear02 Trouble memory clear04 SPF
  counter clear06 Paper feed counter clear07 Drum counter clear08
  Copy counter clear09 Printer counter clear13 Scanner counter
  clear14 SPF jam total counter clear

  25 01 Main motor operation check10 Polygon motor operation
  check

  26 02 Size setting03 Auditor setting05 Count mode setting06
  Destination setting07 Machine condition check (CPM)18 Toner save
  mode setting30 CE mark conformity control ON/OFF31 Auditor mode
  exclusive setup36 Cancel of stop at maintenance life over37 Cancel
  of stop at developer life over38 Cancel of stop at drum life over39
  Memory capacity check42 Transfer ON/OFF timing control setting43
  Side void amount setting51 Copy temporary stop function setting

  30 01 Paper sensor status display42 01 Developing counter
  clear43 01 Fusing temperature setting

  12 Standby mode fusing fan rotation setting13 Fusing paper
  interval control allow/inhibit setting

  44 34 Transfer current setting40 Setting of rotation time before
  toner supply

  46 01 Copy density adjustment (300dpi)02 Copy density adjustment
  (600dpi)09 Copy exposure level adjustment, individual setting

  (Text) 300dpi10 Copy exposure level adjustment, individual
  setting

  (Text) 600dpi11 Copy exposure level adjustment, individual
  setting

  (Photo) 600dpi18 Image contrast adjustment (300dpi)19 Exposure
  mode setting

  (Gamma table setting/AE operation mode setting/Photo image
  process setting)

  20 SPF exposure correction29 Image contrast adjustment
  (600dpi)30 AE limit setting31 Image sharpness adjustment

  48 01 Main scanning magnification ratio adjustment05 SPF/RSPF
  mode sub scanning magnification ratio

  adjustment in copying49 01 Flash ROM program writing mode

  12 Standby mode fusing fan RPM setting

  Main code

  Sub code Contents

  [07]SIMULATIONS.fm 1

  www.

  tehran

  copy

  .com

• AR-5316/5320 SIMULATIONS 7-2

  4. Contents of simulations

  50 01 Image lead edge adjustment06 Copy lead edge position
  adjustment (SPF/RSPF)10 Paper off-center adjustment12 Document
  off-center adjustment

  51 02 Resist amount adjustment53 08 SPF scanning position
  automatic adjustment

  10 SPF scan position change-over setting61 03 HSYNC output check
  63 01 Shading check

  07 SPF automatic correction64 01 Self print

  Main code

  Sub code Contents

  Main code

  Sub code Contents Details of operation

  01 06 Mirror scanning operation aging When the [START] key is
  pressed, the mirror base performs A3 full scanning at the set
  magnification ratio speed. During scanning, the set magnification
  ratio is displayed. After 3 seconds, the mirror base performs full
  scanning again. During scanning, the set magnification ratio is
  displayed. * When the [START] key is pressed again, the ready lamp
  turns and remains off.

  The DV replacement/OPC drum cartridge replacement lamp displays
  the status of the mirrorhome position sensor. (The lamp lights up
  when the mirror is in the home position.)During aging, the copy
  lamp lights up. When the [Interrupt] key is pressed, the operation
  isinterrupted if operating, and the machine goes into the sub code
  input standby mode.

  02 01 Single paper feeder (SPF) aging When the [START] key is
  pressed, the set magnification ratio is acquired and document
  transport operation of single surface is performed in the case of
  SPF or document transport operation of duplex surfaces is
  performed. During operation, the LED on the display section
  corresponding to the selected magnification ratio lights up, and
  the magnification ratio is displayed on the 7-seg display. When the
  [Interrupt] key is pressed at that time, the machine goes to the
  sub code input standby mode. When the [CA] key is pressed, the
  simulation is terminated.

  02 SPF sensor status display (In order to receive the sensor
  change notification, the load must be decreased.)The sensor status
  (ON/OFF) in the SPF can be checked with the following lamps.When a
  sensor detects paper, it turns on. The open/close detection sensor
  turns on when the machine is opened.

  When the [Interrupt] key is pressed, the machine goes to the sub
  code input standby mode. When the [CA] key is pressed, the
  simulation is terminated.

  06 01 Paper feed solenoid operation check

  When this simulation is executed, the sub code is displayed on
  the 7-seg LED and the lamp corresponding to the solenoid lights up.
  Select a solenoid with the tray select key (the lamp corresponding
  to the solenoid lights up) and press the [START] key, and the
  machine repeats operation of ON for 500ms and OFF for 500ms.This
  operation is repeated 20 times.After that, the machine goes into
  the sub code entry standby mode. When [INTERRUPT] key is pressed
  during the process, the machine goes into the sub code input
  standby mode. When [CA] key is pressed, the simulation is
  terminated.

  Display lamp SensorToner supply lampCopier jam lampThe DV
  replacement/OPC drum cartridge replacement lampPaper empty lampSPF
  jam lampManual paper feed lampTray jam lampAE lampTEXT lampPHOTO
  lamp

  SPF document set sensorSPF document transport sensorSPF unit (OC
  cover) open/close sensor

  SPF paper exit sensorSPF paper feed cover open/close sensorSPF
  paper length sensor 1SPF paper length sensor 2SPF paper feed width
  sensor (small)SPF paper feed width sensor (middle)SPF paper feed
  width sensor (large)

  * Supported for the installed models only. Skipped for the
  models without installation.

  Display lamp SolenoidMain cassette lamp 2nd cassette lampManual
  paper feed lamp2nd cassette jam lampMachine jam lamp & 2nd
  cassette jam lamp

  Main cassette paper feed solenoid* 2nd cassette paper feed
  solenoidManual paper feed solenoid* 2nd cassette paper transport
  solenoid* 3rd cassette transport solenoid

  [07]SIMULATIONS.fm 2

  www.

  tehran

  copy

  .com

• AR-5316/5320 SIMULATIONS 7-3

  06 02 Resist roller solenoid operation check

  When the [START] key is pressed in the sub code input state, the
  resist solenoid (RRS) turns ON for 500ms and OFF for 500ms. This
  operation is repeated 20 times. After completion of the process,
  the machine goes into the sub code input standby mode. When
  [INTERRUPT] key is pressed during the process, the machine goes
  into the sub code input standby mode. When [CA] key is pressed, the
  simulation is terminated.

  10 Cassette semi-circular roller cleaning

  First of all, remove the developer unit. Enter the simulation
  code, specify the cassette to be cleaned with the tray select key,
  and press START button. The main motor rotates to move the cassette
  semi-circular roller by half circle and make the roller face
  downward. After completion of cleaning, when INTERRUPT key is
  pressed, the machine goes into the sub code entry standby mode and
  the roller returns to the original positions. To clean another
  roller continuously, press INTERRUPT key to return the roller to
  the original position, and execute the simulation again. During the
  operation, the sub code is displayed on the display. * When CA key
  is pressed, the simulation mode is terminated.

  However, the roller returns to the original position by the
  initial operation.08 01 Developing bias output When the [START] key
  is pressed, the developing bias signal is turned ON for 30 sec.

  However, to calculate the actual output value is calculated,
  execute SIM25-01.After completion of the process, the machine goes
  into the sub code input standby mode. When [INTERRUPT] key is
  pressed during the process, the machine goes into the sub code
  input standby mode. When [CA] key is pressed, the simulation is
  terminated.

  02 Main charger output (Grid = HIGH) When the [START] key is
  pressed, the main charger output is supplied for 30 sec in the grid
  voltage HIGH mode. After completion of the process, the machine
  goes into the sub code input standby mode.When [INTERRUPT] key is
  pressed during the process, the machine goes into the sub code
  input standby mode. When [CA] key is pressed, the simulation is
  terminated.

  03 Main charger output (Grid = LOW) When the [START] key is
  pressed, the main charger output is supplied for 30 sec in the grid
  voltage LOW mode. After completion of the process, the machine goes
  into the sub code input standby mode.When [INTERRUPT] key is
  pressed during the process, the machine goes into the sub code
  input standby mode. When [CA] key is pressed, the simulation is
  terminated.

  06 Transfer charger output Select an output mode with the [Mode
  select] key and press the [START] key. The transfer charger output
  is delivered for 30 sec in the selected mode. After 30 sec of
  transfer charger output, the machine goes into the sub code entry
  standby mode. When [INTERRUPT] key is pressed during the process,
  the machine goes into the sub code input standby mode. When [CA]
  key is pressed, the simulation is terminated.

  22 01 Maintenance counter display The maintenance counter value
  is displayed. (Alternate display by 3 digits)04 Jam total counter
  display The jam total counter value is displayed. (Alternate
  display by 3 digits)05 Total counter display The total counter
  value is displayed. (Alternate display by 3 digits)06 Developing
  counter display The developing counter data is acquired and
  displayed on the 7-seg display. (Alternate display by 3

  digits)When the [Interrupt] key is pressed, the machine goes
  into the sub code input standby mode. When the [CA] key is pressed,
  the simulation is terminated.

  08 SPF counter display The SPF counter value is displayed.
  (Alternate display by 3 digits)14 P-ROM version display The P-ROM
  version is displayed on the copy quantity display. The main code
  and the sub code are

  alternatively displayed by 2 digits. The display interval is
  same as that of the counter display. By pressing the fixed
  magnification ratio key, each version display is switched.

  17 Copy counter display The copy counter value is displayed.
  (Alternate display by 3 digits) When the [Interrupt] key is
  pressed, the machine goes into the sub code input standby mode.
  When the [CA] key is pressed, the simulation is terminated.

  18 Printer counter display The printer counter value is
  displayed. (Alternate display by 3 digits)When the [Interrupt] key
  is pressed, the machine goes into the sub code input standby mode.
  When the [CA] key is pressed, the simulation is terminated.

  21 Scanner counter display The scanner counter value is
  displayed. (Alternate display by 3 digits)When the [Interrupt] key
  is pressed, the machine goes into the sub code input standby mode.
  When the [CA] key is pressed, the simulation is terminated.

  Main code

  Sub code Contents Details of operation

  Small size is Letter R (A4R) or smaller.

  Display lamp Output modeAE mode lampAE mode lamp & PHOTO
  mode lampAE & TEXT & PHOTO mode lamp

  Normal size width: Front surfaceSmall size width: Front
  surfaceManual paper feed mode

  Display lamp (AB series) Display lamp (Inch series) Displayed
  version141% 141% Machine program

  [07]SIMULATIONS.fm 3

  www.

  tehran

  copy

  .com

• AR-5316/5320 SIMULATIONS 7-4

  22 22 SPF jam counter display The SPF jam counter value is
  displayed. (Alternate display by 3 digits)When the [Interrupt] key
  is pressed, the machine goes into the sub code input standby mode.
  When the [CA] key is pressed, the simulation is terminated.

  44 34 Transfer current setting Used to set the transfer current
  for the front surface and that for the back surface. When this
  simulation is executed, the current set value is displayed on the
  7-seg display. Select the set value with the zoom (Up/Down) keys
  and press the [START] key, and the set content is written into the
  EEPROM and the machine goes into the sub code input standby mode.
  Press the [Mode select] key to select each setting mode. At that
  time, the setup content is written into the EEPROM. The set range
  is 90uA ~ 360uA in the increment of 10uA.

  * Small size paper must be Letter R (A4R) or smaller.* For the
  special size of tray, use the normal size width.

  49 01 Flash ROM program writing mode (Operating procedure)When
  this simulation is executed, «d» is displayed on the copy quantity
  display and the machine enters the Flash ROM program writing mode.
  Use the writing tool on the PC to write the program. During
  writing, the display is made as follows. After completion of
  downloading, turn OFF/ON the power to reset.

  * «*» in the error display indicates the error position.

  12 Standby mode fusing fan RPM setting

  When this simulation is executed, the currently set code number
  is displayed. When [MODE SELECT] key is pressed, the normal setting
  and the high fusing temperature setting are switched alternatively.
  Enter the code number and press START key, and the number is
  written into the EEPROM and the machine goes into the sub code
  entry standby mode.

  Main code

  Sub code Contents Details of operation

  Display lamp Setting mode AE mode lampAE mode lamp & PHOTO
  mode lampAE & TEXT & PHOTO mode lamps

  Normal size width: FrontSmall size width: FrontManual paper
  feed

  Status Copy quantity display Pre-heat lamp Ready lampDownload
  data receptionData delete startData writing (Boot section)Data
  writing (Program section)Sum checkCompletion of downloadingError
  status

  «d»»d»»d»»d»»d»»OFF»»*E»

  ONONFlashFlashONOFFOFF

  OFFONOFFFlashONOFFOFF

  00 Data receive error 07 Sum check error (Program section)02
  FLASH ROM delete error 08 Sum check error (EEPROM section)03 FLASH
  ROM write error (Boot section) 09 E2PROM verify error04 FLASH ROM
  write error (Program section) 0b E2PROM verify error05 Sum check
  error (Loader section) 0F Download data length error06 Sum check
  error (Boot section)

  Display lamp Setting mode DefaultAE mode lamp Normal temperature
  control (190C or less) Low speed rotationTEXT mode Fusing
  temperature of 190C or above High speed rotation

  Code number Setting01

  Low speed rotationHigh speed rotation

  [07]SIMULATIONS.fm 4

  www.

  tehran

  copy

  .com

• AR-5316/5320 SIMULATIONS 7-5

  51 02 Resist amount adjustment Used to adjust the contact
  pressure of the machine resist roller and the RSPF resist roller
  onto the paper. (Operating procedure)When this simulation is
  executed, the current set value is displayed. When the exposure
  mode key is pressed, the following set items are changed
  sequentially. Enter an adjustment value with the 10-key and press
  the [START] key, and the entered value will be saved and a copy
  will be made. (Adjustment range: 1 ~ 99, Default: 50)When the [CA]
  key is pressed, the entered value is saved and the simulation is
  terminated.

  Supported for the installed models only. Skipped for the models
  without installation.53 10 SPF scan position change-over

  settingUsed to change over the scan position depending on that
  the SPF unit and the SPF document glass holder section are of
  anti-dirt glass or not. When this simulation is executed, the
  currently set code number is displayed. Enter the code number
  corresponding to the SPF unit to be used and press [START] key, and
  the setting will be changed over.

  Though this setting is changed, the other set values are not
  affected. (The other set values remain unchanged.)When replacing
  and installing the SPF unit, it is recommendable to use this
  simulation to set the scan position and execute the scan position
  automatic adjustment.

  64 01 Self print The optical system status is ignored and a self
  print is made. Also when a print command is sent from the host,
  printing is performed. (Operating procedure)When this simulation is
  executed, warm-up is performed and the ready lamp is lighted.
  (However, the scanner is invalid and no initial operation is
  made.)Enter the code number with the 10-key, and select a cassette
  with the cassette select key and press the [START] key. The
  selected cassette start paper feed and printing is performed in the
  selected pattern.* Only the tray lamp and the online lamp are
  lighted, and no other lamps are lighted. Printing is made in 1 by 2
  mode, where one line is printed and the following two liens are not
  printed, or in the grid pattern.

  * Input disable for 4 ~ 99* Print data are made on A3 size. (A3
  paper is preferable.)

  Main code

  Sub code Contents Details of operation

  Lighting lamp Adjustment modeAE, Main cassette lampAE, 2nd
  cassette lampAE, Manual paper feed lampAE, TEXT, PHOTO lamps

  Main cassette paper feed2nd cassette paper feed

  Manual paper feedSPF document feed (Front surface)

  Code No. Mode0 Set to the scan position of the current mass
  production SPF unit. (Default)1 Set to the scan position of the
  ant-dirt SPF unit.

  Code number Pattern0123

  1 by 2Grid patternWhite paperBlack background

  [07]SIMULATIONS.fm 5

  www.

  tehran

  copy

  .com

• AR-5316/5320 USER PROGRAMS 8-1

  [8] USER PROGRAMSThe user programs allow the parameters of
  certain functions to be set, changed, or canceled as desired.

  1. List of user programsThis copier has the following user
  programs.

  *1 On models with a SPF.*2 On model with the two trays.

  Program name Program No Description Default Parameters

  Auto clear time

  1

  «Auto clear time» automatically returns the copy settings to the
  initial settings when a certain period of time elapses after a copy
  is made. This program is used to select the period of time. «Auto
  clear time» can also be disabled. 60sec

  1 (OFF)2 (10sec)3 (20sec)4 (60sec)5 (90sec)6 (120sec)

  Preheat mode

  2

  This function automatically switches the machine to a low power
  consumption state if the set duration of time elapses without the
  machine being used when the power is on.The POWER SAVE indicator
  lights up, however, the keys on the operation panel can be used.
  Normal operation automatically resumes when a key on the operation
  panel is pressed, a print job is received or an original is
  placed.

  1min

  1 (1min)2 (5min)3 (30min)4 (60min)5 (120min)6 (240min)

  Auto power shut-off timer

  3

  This function automatically switches the machine to a state that
  consumes even less power than preheat mode if the set duration of
  time elapses without the machine being used when the power is on.
  All lights except the POWER SAVE indicator and ON LINE indicator go
  off. To resume normal operation, press the [START] key. Normal
  operation also resumes automatically when a print job is received
  or scanning is begun from a computer. While in auto power shut-off
  mode, no keys (except the [START] key) can be used.

  5min

  1 (5min)2 (30min)3 (60min)4 (120min)5 (240min)

  Stream feeding mode *1

  4

  When copying using the SPF, during the period of time that the
  SPF indicator blinks after an original has been scanned (about 5
  seconds), a subsequent original can be placed and automatically fed
  into the machine.

  OFF

  0 (OFF)1 (ON)

  Auto power shut-off setting 5

  Use this setting to enable or disable auto power shut-off.ON

  0 (OFF)1 (ON)

  Auto paper select mode *28

  This function automatically selects paper that is the same size
  as the original placed in the SPF, or the same size as that
  selected with the [ORIGINAL SIZE ENTER] key. The function can be
  disabled.

  ON0 (OFF)1 (ON)

  Auto tray switching *2

  9

  If the paper runs out during printing and there is paper of the
  same size and orientation in another tray, this function
  automatically switches to that tray (excluding the bypass tray).
  The function can be disabled.

  ON

  0 (OFF)1 (ON)

  Auditing mode10

  Use to enable or disable «Auditing mode».»Auditing mode» is
  initially disabled. OFF

  0 (OFF)1 (ON)

  Account number entry 11 Use to set up account numbers. Up to 20
  accounts can be established. — —

  Account number change 12 Use to change an account number. —
  -Account number deletion

  13Use to delete an account number.A single account number can be
  deleted, or all account numbers at once.

  Delete single

  account

  0 (Delete single account)1 (Delete all accounts)

  Number of copies per account 14

  This displays the number of copies made by each account.The
  maximum count is 49,999. If this number is exceeded, the count will
  start over from 0.

  — —

  Resetting account15

  Use to reset the copy count of an account to 0.The copy count of
  a single account or of all accounts can be reset.

  Reset single account

  0 (Reset single account)1 (Reset all accounts)

  Resolution in Auto/Text mode 23

  This setting is used to change the copy resolution in AUTO and
  TEXT mode from 600 x 300 dpi to 600 x 600 dpi (high-quality
  mode).Scanning is slower when high-quality mode is used.

  300dpi

  1 (300dpi)2 (600dpi)

  [08]USERPROGRAMS.fm 1

  www.

  tehran

  copy

  .com

• AR-5316/5320 USER PROGRAMS 8-2

  Program name Program No Description Default Parameters

  Key auto repeat

  25

  Use this setting to select whether or not holding down a key
  causes repeated input of the key. For keys that normally cause a
  set value to increase when held down (for example, holding down the
  [ZOOM] key), this program can be used to have the set value not
  change when the key is held down.

  ON

  0 (OFF)1 (ON)

  Key press time

  26

  Use this setting to select how long a key must be pressed for
  the input to be accepted. By selecting a longer time, you can
  prevent settings from being changed by the accidental pressing of a
  key. Minimum (current

  response speed)

  1 (Minimum(current response speed))2 (0.5sec)3 (1.0sec)4
  (1.5sec)5 (2.0sec)

  Audible signals volume27

  This sets the volume of beep signals.short beep

  1 (short beep)2 (long beep)3 (OFF)

  Base setting beep signal28

  Use this to sound a beep when a base setting is selected.OFF

  0 (OFF)1 (ON)

  Number of copies limit29

  Use this setting to select 99 or 999 for the maximum number of
  copies. 999 copies

  1 (99 copies)2 (999 copies)

  Use close paper size

  30

  When this function is enabled, printing in printer mode will
  automatically continue using a different size of paper if the
  specified size of paper runs out in all trays. This feature does
  not function in copy mode.

  OFF

  0 (OFF)1 (ON)

  Default tray setting31

  Use this program to select a default tray. This tray is
  automatically selected each time the power is turned on or each
  time the machine reverts to the initial settings.

  Upper paper tray

  1 (Upper paper tray)2 (Lower paper tray)5 (Bypass tray)

  Default exposure mode32

  Use this program to set «AUTO», «TEXT», or «PHOTO» as the
  default exposure mode. AUTO

  1 (AUTO)2 (TEXT)3 (PHOTO)

  [08]USERPROGRAMS.fm 2

  www.

  tehran

  copy

  .com

• AR-5316/5320 MAINTENANCE 10-1

  [10] MAINTENANCE1. Maintenance table

  X:Check(Clean, adjust, or replace when required.) O:Clean
  :Replace :Adjust :Lubricate

  *1:Recommendable replacement time:50K(Letter,5%print)

  Unit name Part name When calling 50K 100K 150KDrum peripheral
  OPC drum —

  Cleaning blade -Side seal F/R X X X XMC unit X(MC charging
  electrode) — ( ) ( ) ( )(MC grid) — ( ) ( ) ( )(MC case) — ( ) ( )
  ( )Transfer wire O O O OTransfer paper guide O O O OMC guide sheet
  (Cleaning blade attached) -Drum fixing plate B XProcess frame unit
  X X XDischarge holder O O O OSeparation pawl Star ring x 2 pcs
  X

  Developing section Developer -DV seal — X XDV under seal — — -DV
  side seal — X XSide Mylar — — —

  Optical section Lamp unit Reflector O O O OMirror O O O O

  No.2/3 mirror unit Mirror O O O OPulley X X X X

  CCD peripheral Lens O O O OGlass Table glass O O O O

  White Plate O O O OOther Drive wire X X X X

  Rail X X X XDocument cover O O O ODocument size sensor O O O
  O

  LSU Dust-proof glass O O O OPaper feed section Multi paper feed
  section Take-up roller(manual / SPF) O O O O

  Paper feed roller O O O OSpring clutch O O O O

  Paper transport section PS roller O O O OTransport (paper exit)
  rollers O O O OSpring clutch O O O O

  Fusing section Upper heat roller O O OPressure roller O O O
  OPressure roller bearing X X X OUpper separation pawl X X X OLower
  separation pawl X X X OCleaning pad X X X

  Drive section Gears X X X XBelts X X X O

  Paper exit section Ozone filter*1 X X X X

  Only for Viet Nam

  [10]MAINTENANCE.fm 1

  www.

  tehran

  copy

  .com

• AR-5316/5320 MAINTENANCE 10-2

  2. Maintenance display system

  *1: Installation of a new toner cartridge allows to display the
  remainingquantity.

  3. Note for replacement of consumable partsA. Toner
  cartridgeWhen a waste toner cartridge is removed from the machine,
  it must beput in a polyethylene bag to avoid scattering of
  toner.

  B. DV cartridgeDo not shake or put up the developer cartridge.
  Otherwise developermay scatter.

  C. DV seal attachment procedure

  1) When attaching the DV side Mylar, check the position shown in
  thefigure below and attach it properly.

  2) When attaching the DV side sheet, check the position shown in
  thefigure below and attach it properly. (First of all, attach the
  DV side Mylar.)

  * Be sure to attach the DV side sheet so that the notch is on
  theoutside.

  Toner Life, 16KRemaining quantity check *1

  a. Press and hold the density adjustment LIGHT key for more than
  5 sec, and the machine will enter the user program mode.

  b. Press and hold the «%» key for more than 5 sec, and the
  remaining quantity will be displayed on the copy quantity display
  in one of the following levels: (Remaining quantity display levels:
  100%, 75%, 50%, 25%, 10%, LO)

  c. Press the density adjustment LIGHT key to cancel.

  Remaining quantity

  NEAR EMPTYAbout 10%

  EMPTY

  LED ON FlashMachine Operation allowed Stop

  Developer Life 50KLED ON at 50K of the

  developer countMachine Selection is available between Not
  Stop

  and Stop by Service Simulation (SIM 26-37) Setup.(If Stop is
  selected, the LED will flash and stop at 50K.)* Default: Not Stop*
  Clear: SIM 42-1

  Maintenance LED Selection is available among 50K, 25K, 10K,
  7.5K, 5K, and free (no lighting) with SIM 21-1.* Default: 50K*
  Clear: SIM 20-1

  Machine Not stop

  [10]MAINTENANCE.fm 2

  www.

  tehran

  copy

  .com

• AR-5316/5320 ELECTRICAL SECTION 13-1

  [13] ELECTRICAL SECTION1. Block diagram

  Scan

  ner U

  nit

  CCD

  PWB

  5VA5

  V 3.

  3V

  B/W

  8bits

  (MSB

  /LSB

  )

  5V

  ADC

  CLK

  ,SYN

  CH

  ,BS

  AMP,

  VSAM

  PSD

  I,SC

  LK,L

  OAD

  ,OBE

  MO

  DE L

  VTTL

  MCU

  -PW

  B

  3.3V

  IEEE

  128

  4 I/F

  USB

  I/F

  Prin

  ter C

  LK(2

  0.30

  94M

  Hz)

  3.3V

  RIC

  Dow

  nloa

  dSc

  anne

  r CLK

  (48M

  Hz)

  A[19

  …1]

  D[1

  5… 0

  ] 1Mb(

  1Mb*

  1)

  8Mbi

  t

  I2C

  Bus

  4Kby

  te

  Oth

  er L

  oads

  MPF

  S,R

  RS,

  SGS,

  SRR

  C,S

  PUS,

  SPPS

  ,To

  ner M

  otor

  Mai

  n M

  otor

  Mirr

  or M

  otor

  VFM

  CN

  T,VF

  M,M

  PFS,

  CPF

  S2,

  CPF

  S1

  Oth

  er In

  puts

  CPU

  INTE

  RR

  UPT

  SP

  PD

  CPU

  I/O RTH

  DR

  ST

  I/

  F PW

  B

  Zebr

  a2 A

  SIC

  (296

  pin)

  CP

  U H

  8S/2

  320

  (19

  .660

  8MH

  z)

  I E E E 1 2 8 4 U S B 1 . 1

  L

  SU

  Poly

  gon

  Mot

  or

  EEP

  RO

  M

  SDR

  AMSi

  mp

  16M

  byte

  Res

  et IC

  S

  RAM

  Driv

  er

  Flas

  h R

  OM

  AFE(

  AD98

  26)

  C D S

  A G C

  M P X A

  D 16

  bit

  s

  C

  CD

  Driv

  er

  CC

  FL

  Lam

  p In

  verte

  r

  HO

  ME

  POSI

  TIO

  NSE

  NSO

  R

  CC

  D(T

  CD

  1710

  )

  CR

  UM

  CPU

  CLK

  (19.

  6608

  MH

  z)

  Softw

  are

  Res

  et

  SSC

  GPMD

  Driv

  er

  MM_AI0/AI1/PH_A

  MM_BI0/BI1/PH_B

  O

  PU P

  WB

  LC

  7935

  AN7s

  eg L

  ED

  LED

  5V

  HC

  151

  KEY

  5V

  LVC

  1284

  PDIU

  SBP1

  1AD

  STAR

  T KE

  Y

  POW

  ER S

  UPPL

  Y

  /PO

  FF,H

  L,PR

  FW 3.3V

  ,5VE

  N,5

  V,24

  V

  HVU

  TC,G

  RID

  ,MC

  ,BI

  AS

  COIN

  VEN

  DOR/

  AUDI

  TOR

  /CV_

  CO

  PY/C

  V_C

  OU

  NT,

  /CV_

  STAR

  T, /C

  V_C

  A, /CV_

  DPX

  , /C

  V_SI

  ZE0,

  1, 2

  , 3

  PMC

  LK(2

  078.

  74(H

  z))

  PSW

  KIN

  1SE

  LIN

  1,2,

  3

  OP-

  CLK

  OP-

  LATC

  HO

  P-D

  ATA

  OP-

  BEO

  LED

  Ligh

  t onl

  y

  PSL,

  ON

  L

  MH

  PS

  /VID

  EOS/

  HAP

  CST

  T/S

  YNC

  SPM

  T0/1

  /2/3

  SPF

  Driv

  erSP

  FCLH

  ,SP

  FGSO

  LSP

  FPSO

  L,SP

  FRSO

  L

  Sens

  or

  Driv

  er

  Sele

  ctor

  L1,2

  W0,

  1,2,

  3

  /SPF

  CO

  VER

  ,PA

  PER

  ,SP

  FOPE

  N,

  /SPF

  OU

  T

  SPF

  MO

  TOR

  TM+,TM-

  /MMRDY

  /MMD

  PWM

  5V,3

  .3V

  24V

  HC

  151

  CLO

  N

  2nd

  CAS

  SETT

  EFe

  ed S

  OL

  , Pic

  k up

  SO

  LC

  ASSE

  TTE

  DET

  ECTI

  ON

  ,PA

  PER

  DET

  ECTI

  ON

  ,PA

  PER

  PAS

  S D

  ETEC

  TIO

  N,

  DO

  OR

  DET

  ECTI

  ON

  /MMRDY

  SELI

  N1,

  2,3Y1

  PSO

  LFS

  OL

  SCAN

  1-6

  LCX1

  6374

  UAR

  T

  FAN

  [13]ELECTRICALSECTION.fm 1

  www.

  tehran

  copy

  .com

• AR-5316/5320 ELECTRICAL SECTION 13-2

  3. Actual wiring diagramACTUAL WIRING DIAGRAM 1/7

  B03

  P-V

  L(W

  HIT

  E)

  B4B

  -PH

  -K-B

  L(B

  LAC

  K)

  SP

  F G

  RO

  UN

  D W

  IRE

  OR

  IGIN

  AL

  TRA

  Y H

  AR

  NE

  SS

  SE

  NS

  OR

  HA

  RN

  ES

  S

  04FE

  -BT-

  VK

  -N(W

  HIT

  E)

  B3B

  -PH

  -K-R

  (RED

  )

  Mirr

  or H

  PS

  EN

  SO

  R

  OPT

  ICAL

  BAS

  E PL

  ATE

  CC

  D P

  WB

  Mirr

  or M

  OTO

  R

  CO

  PY

  LA

  MP

  THE

  RM

  ISTE

  R

  Sid

  e C

  over

  SW

  MA

  INM

  OTO

  RTO

  NE

  RM

  OTO

  R

  DE

  V U

  N

  POW

  ER P

  WB

  MC

  U-P

  WB

  HA

  ND

  PA

  PE

  R P

  ICK

  UP

  SO

  LEN

  OID

  HA

  ND

  PA

  PE

  R E

  MP

  TYS

  EN

  SO

  R

  TC

  CA

  SE

  TTE

  EM

  PTY

  SE

  NS

  OR

  PS

  SO

  L

  GP

  1S58

  (C)

  GP

  1S58

  (O)

  2nd

  CA

  SE

  TTE

  (O) N

  orm

  al O

  pen

  :Low

  (C

  ) Nor

  mal

  Clo

  se :H

  igh

  GR

  IDM

  C

  MC

  FB

  BC

  HV

  U Bias

  SP

  F U

  NU

  SB

  1.1

  IEE

  E12

  84

  PA

  PE

  R IN

  SE

  NS

  OR

  PIC

  K U

  P S

  OL

  FUS

  ER

  AC

  Cor

  d

  AC

  SW

  HE

  ATE

  R L

  AM

  P

  RE

  AC

  TOL

  230V

  ON

  LY

  PO

  LYG

  ON

  MO

  TOR

  LSU

  AP

  C-P

  WB

  BD

  -PW

  B

  CO

  OLI

  NG

  FU

  N

  I/F

  FFC

  FFC

  FFC

  FFC

  FFC

  FFC

  Fron

  t Cov

  er S

  W

  SR

  U

  CA

  SE

  TTE

  SW

  ITC

  HS

  EN

  SO

  R

  B3B-PH-K-S(WHITE)

  B3B

  -PH

  -K-R

  (RED

  )S

  UB

  -D 2

  5

  FE4-

  32-S

  1505

  (BLA

  CK)

  B4B

  -PH

  -K-S

  (WH

  ITE)

  08FE

  -BT-

  VK

  -N(W

  HIT

  E)B

  2P-V

  H(W

  HIT

  E)B

  3P-V

  H(W

  HIT

  E)

  B3B

  -PH

  -K-S

  (WH

  ITE)

  B20

  B-P

  HD

  SS

  -B(W

  HIT

  E)

  B3B

  -PH

  -K-B

  K(B

  LAC

  K)

  B4B

  -PH

  -K-S

  (WH

  ITE)

  B2B

  -XH

  -A-S

  (WH

  ITE)B2B

  -XH

  -A-B

  K(B

  LAC

  K)

  B2B

  -XH

  -A-R

  (RED

  )B

  4B-P

  H-K

  -R(R

  ED)

  B12

  B-P

  HD

  SS

  -B(W

  HIT

  E)

  B26

  B-P

  HD

  SS

  -B(W

  HIT

  E)

  35FE

  -BT-

  VK

  -N(W

  HIT

  E)

  13FE-BT-VK-N(WHITE)

  B7B-PH-K-S(RED)

  B18B-PHDSS-B(WHITE)

  B4B

  -PH

  -K-S

  (WH

  ITE)

  3P T

  ER

  MIN

  AL

  230V

  ON

  LYB

  4B-P

  H-K

  -S(W

  HIT

  E)

  35FE-BT-VK-N(WHITE)

  DR

  UM

  INIS

  AL

  SW

  B3B-PH-K-BK(BLACK)

  B3B

  -PH

  -K-S

  (WH

  ITE)

  SH

  IFTE

  R

  MO

  TOR

  GP

  1A71

  A1(

  O)

  SH

  IFTE

  R H

  PS

  EN

  SO

  RC

  OO

  LIN

  GFU

  NC

  OO

  LIN

  GFU

  N

  13FE-BT-VK-N(WHITE)

  MO

  DE

  L W

  /O S

  HIF

  TER

  MO

  DE

  L W

  ITH

  SH

  IFTE

  R

  B3B-PH-K-SX2

  (WHITE)

  CO

  OLI

  NG

  FUN

  CO

  OLI

  NG

  FUN

  CO

  PY

  OP

  PW

  B

  OP

  ER

  ETI

  ON

  PA

  NE

  L

  IMSA-9610S-24C

  (BLACK)

  Opt

  ion

  B6B-PH-K-S(WHITE)

  PA

  PE

  R O

  UT

  SE

  NS

  OR

  DU

  PS

  EN

  SO

  R

  24FMN-BTRK-A(BLACK)

  3

  *

  [13]ELECTRICALSECTION.fm 2

  www.

  tehran

  copy

  .com

• LEAD-FREE SOLDERThe PWBs of this model employs lead-free solder.
  The LF marks indicated on the PWBs and the Service Manual mean
  Lead-Free solder. The alphabet following the LF mark shows the kind
  of lead-free solder.

  (1) NOTE FOR THE USE OF LEAD-FREE SOLDER THREADWhen repairing a
  lead-free solder PWB, use lead-free solder thread.Never use
  conventional lead solder thread, which may cause a breakdown or an
  accident.Since the melting point of lead-free solder thread is
  about 40C higher than that of conventional lead solder thread, the
  use of the exclusive-usesoldering iron is recommendable.

  (2) NOTE FOR SOLDERING WORKSince the melting point of lead-free
  solder is about 220C, which is about 40C higher than that of
  conventional lead solder, and its soldering capacity isinferior to
  conventional one, it is apt to keep the soldering iron in contact
  with the PWB for longer time. This may cause land separation or may
  exceedthe heat-resistive temperature of components. Use enough care
  to separate the soldering iron from the PWB when completion of
  soldering isconfirmed.Since lead-free solder includes a greater
  quantity of tin, the iron tip may corrode easily. Turn ON/OFF the
  soldering iron power frequently.If different-kind solder remains on
  the soldering iron tip, it is melted together with lead-free
  solder. To avoid this, clean the soldering iron tip aftercompletion
  of soldering work.If the soldering iron tip is discolored black
  during soldering work, clean and file the tip with steel wool or a
  fine filer.

  Example:

  5mm

  Lead-Free

  Solder compositioncode (Refer to thetable at the right.)

  Solder
  compositionSn-Ag-CuSn-Ag-BiSn-Ag-Bi-CuSn-Zn-BiSn-In-Ag-BiSn-Cu-NiSn-Ag-SbBi-Sn-Ag-PBi-Sn-Ag

  a

  b

  z

  in

  s

  p

  Solder composition code

  a

  [14]LeadFree.fm 1

  www.

  tehran

  copy

  .com

• COPYRIGHT 2003 BY SHARP CORPORATIONAll rights reserved.Printed
  in Japan.

  No part of this publication may be reproduced,stored in a
  retrieval system, or transmitted,

  in any form or by any means,electronic, mechanical,
  photocopying, recording, or otherwise,

  without prior written permission of the publisher.

  Trademark acknowledgmentsWindows and Windows NT are trademarks
  of Microsoft Corporation in the U.S.A.and other countries.IBM and
  PC/AT are trademarks of International Business Machines
  Corporation.PCL is a trademark of Hewlett-Packard Company.Pentium
  is a registered trademark of Intel Corporation.All other trademarks
  and copyrights are the property of their respective owners.

  SHARP CORPORATIONDigital Document System GroupProducts Quality
  Assurance DepartmentYamatokoriyama, Nara 639-1186, Japan

  N

  c

  All rights reserved.Printed in Japan.

  No part of this publication may be reproduced,stored in a
  retrieval system, or transmitted,

  in any form or by any means,electronic, mechanical,
  photocopying, recording, or otherwise,

  without prior written permission of the publisher.

  Trademark acknowledgmentsWindows and Windows NT are trademarks
  of Microsoft Corporation in the U.S.A.and other countries.IBM and
  PC/AT are trademarks of International Business Machines
  Corporation.PCL is a trademark of Hewlett-Packard Company.Pentium
  is a registered trademark of Intel Corporation.All other trademarks
  and copyrights are the property of their respective owners.

  N

  c

  All rights reserved.Printed in Japan.

  No part of this publication may be reproduced,stored in a
  retrieval system, or transmitted,

  in any form or by any means,electronic, mechanical,
  photocopying, recording, or otherwise,

  without prior written permission of the publisher.

  Trademark acknowledgmentsWindows and Windows NT are trademarks
  of Microsoft Corporation in the U.S.A.and other countries.IBM and
  PC/AT are trademarks of International Business Machines
  Corporation.PCL is a trademark of Hewlett-Packard Company.Pentium
  is a registered trademark of Intel Corporation.All other trademarks
  and copyrights are the property of their respective owners.

  2003 Dec. Printed in Japan N

  c

  [00]COVER.fm 2

  www.

  tehran

  copy

  .com