-
Contents
-
Table of Contents
-
Bookmarks
Quick Links
O P E R A T I N G I N S T R U C T I O N S
M4000 Advanced,
M4000 Advanced A/P and
M4000 Area 60/80
Multiple Light Beam Safety Device
en
Related Manuals for SICK M4000 Advanced
Summary of Contents for SICK M4000 Advanced
-
Page 1
O P E R A T I N G I N S T R U C T I O N S M4000 Advanced, M4000 Advanced A/P and M4000 Area 60/80 Multiple Light Beam Safety Device… -
Page 2: Yt72/2016
This document is protected by the law of copyright, whereby all rights established therein remain with the company SICK AG. Reproduction of this document or parts of this document is only permissible within the limits of the legal determination of Copyright Law. Alteration or abridgement of the document is not permitted without the explicit written approval of the company SICK AG.
-
Page 3: Table Of Contents
Muting using two sensors, serial placement (one sensor pair in the hazardous area), with additional signal C1, exit monitoring with End of muting by ESPE………..32 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice…
-
Page 4
7.2.3 Mounting with side bracket………….. 74 7.2.4 Mounting with rigid mounting bracket ……….76 7.2.5 Mounting with pivoting mounting bracket……..78 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice… -
Page 5
SICK support………………… 105 12.3 Error displays of the LEDs…………….106 12.4 Error displays of the 7Esegment display…………107 12.5 Extended diagnostics………………112 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice… -
Page 6
Checklist for the manufacturer …………….142 15.3 Alignment templates ………………143 15.4 Alignment instructions………………145 15.5 List of tables …………………147 15.6 List of illustrations ………………..149 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice… -
Page 7: About This Document
General information on accident prevention using opto-electronic protective devices can be found in the SICK brochure “Safe Machines with opto-electronic protective devices”. We also refer you to the SICK homepage on the Internet at www.sick.com. Note Here you will find information on:…
-
Page 8: Scope
If reference is made in this document to sens:Control devices, safety controllers and network solutions are meant. The UE403 safety relay is an accessory for the SICK M4000 Advanced multiple light beam UE403 safety device. It extends the technical application possibilities of the M4000 Advanced.
-
Page 9: Symbols Used
8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice…
-
Page 10: On Safety
Transparent objects are not detected. Depending on the application, mechanical protective devices may be required in addition to the M4000 system. © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 11: Correct Use
All warranty claims against SICK AG are forfeited in the case of any other use, or altera- tions being made to the system, even as part of their mounting or installation.
-
Page 12: Environmental Protection
Metal recycling (aluminium) Circuit boards, cable, connector and Electronic recycling electrical connecting pieces Packaging Cardboard, paper Paper/cardboard recycling Polyethylene packaging Plastic recycling © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 13: Product Description
M4000 Area 80: – corresponds: 80 mm resolution – length of the monitored area 600-1800 mm – scanning range 70 m 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice…
-
Page 14: Operating Principle Of The Device
M4000 Advanced A/P M4000 Advanced A/P Beam separation Dimension of the light path between M4000 Advanced A/P and M4000 Passive (deflector unit) © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 15
M4000 Advanced The M4000 Advanced multiple light beam safety device is available with 2, 3 or 4 beams. Other configurations with up to 12 beams are possible on request. The maximum scanning range (dimension of the light path between sender and receiver) is 70 m. -
Page 16: Application Examples
M4000 Advanced multiple light beam safety device Fig. 5: Access protection with an M4000 Advanced A/P multiple light beam safety device © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 17: Access Protection On Several Sides With The Aid Of Deflector Mirrors
You can secure two sides of a hazardous area by using one deflector mirror (see Fig. 7), with two deflector mirrors you can secure three sides (see Fig. 8). 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice…
-
Page 18
(see chapter 5.4 “Scanning range” on page 42ff). You can extend the M4000 Advanced A/P multiple light beam safety device with a maxi- mum of one deflector mirror. © SICK AG • Industrial Safety Systems • Germany • All rights reserved… -
Page 19: Controls And Status Indicators
Point not visible: The bottom edge of the numbers on the 7Esegment display is pointing towards the LED display. Device symbol M4000 Advanced (sender or receiver), M4000 Advanced (A/P) or M4000 Area (sender or receiver), context menu Open device window, parameter node General.
-
Page 20: Status Indicators Of The Sender
Operation with code 2 (only after switching on) Other All other displays are error messages. Please refer to chapter 12 “Fault displays diagnosis” on page 105. © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 21: Status Indicators Of The Receiver Or Of The M4000 Advanced A/P
Operation with code 2 (only after switching on) Other All other displays are error messages. Please refer to chapter 12 “Fault displays diagnosis” on page 105. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice…
-
Page 22: Muting
Chapter 4 Operating Instructions M4000 Adv., Adv. A/P, Area Muting When using the muting functions of the M4000 Advanced please observe the operating Note instructions of the corresponding UE403 or sens:Control device. Pay attention to the following safety notes! Muting is only allowed to be activated during the period when the material to be trans- ported (e.g.
-
Page 23: Muting Principle
Exception: With the Exit monitoring function activated (see sections 4.2.3 and 4.2.4 from page 30), multiple material transport within a muting cycle is not possible. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice…
-
Page 24: Muting Sensors
WS27/WE27 WS280/WE280 Note For the selection and settings for the SICK optical muting sensors in muting applications, the following applies: Outputs must be PNP switching. Other series are possible. Pay attention to the output signals in chapter 6.2.
-
Page 25: Muting Lamp
To signal muting, the use of a muting lamp or a muting status signal is stipulated. The muting lamp signals the temporary muting. You can use an external lamp (monitored/not monitored) or the integrated LED on the M4000 Advanced multiple light beam safety device (not monitored).
-
Page 26: Muting With Two Sensors (One Sensor Pair), Crossed Placement
Tab. 6: Conditions for muting Condition Description with two sensors, crossed A1 & A2 Muting applies as long as this condition is met. placement © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 27
– Monitoring of the total muting time, see page 51 ff. – End of muting by ESPE, see page 53 ff. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice… -
Page 28: Muting With Two Sensors (One Sensor Pair), Crossed Placement, And An Additional Signal C1
(e.g. A1 and A2) are active. A1 & A2 Muting applies as long as this condition is met. © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 29
– Monitoring of the total muting time, see page 51 ff. – End of muting by ESPE, see page 53 ff. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice… -
Page 30: Muting Using Two Sensors, Serial Placement (One Sensor Pair In The Hazardous Area), Exit Monitoring With End Of Muting By Espe
A1 & ESPE or Muting applies as long as this condition is met. The muting A2 & ESPE or ESPE hold time counts down. © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 31
– Sensor test, see page 50ff. – Concurrence monitoring, see page 51ff. – Monitoring of the total muting time, see page 51ff. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice… -
Page 32: Muting Using Two Sensors, Serial Placement (One Sensor Pair In The Hazardous Area), With Additional Signal C1, Exit Monitoring With End Of Muting By Espe
A1 & ESPE or Muting applies as long as this condition is met. The muting A2 & ESPE hold time counts down. © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 33
– Sensor test, see page 50ff. – Concurrence monitoring, see page 51ff. – Monitoring of the total muting time, see page 51ff. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice… -
Page 34: Muting With Four Sensors (Two Sensor Pairs), Serial Placement
Muting applies as long as this condition is met. The second (or A1 & A2) sensor pair is activated as a function of the direction of trans- port of the material. © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 35
– Monitoring of the total muting time, see page 51 ff. – End of muting by ESPE, see page 53 ff. – Sequence monitoring, see page 55 ff. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice… -
Page 36: Muting With Four Sensors (Two Sensor Pairs), Parallel Placement
Muting applies as long as this condition is met. The second (or A1 & A2) sensor pair is activated as a function of the direction of trans- port of the material. © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 37
– Monitoring of the total muting time, see page 51 ff. – End of muting by ESPE, see page 53 ff. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice… -
Page 38: Configurable Functions
The person who makes the change is also responsible for the correct protective function of the device. When making configuration changes, please always use the password hierar- chy provided by SICK to ensure that only authorised persons make changes to the configu- ration. The SICK service team is available to provide assistance if required.
-
Page 39
The reset button prevents the accidental and inadvertent operation of the external restart Recommendation button. The operator must first acknowledge the safe state with the reset button. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice… -
Page 40: Beam Coding
After switching on, the 7Esegment display of sender and receiver will briefly display the coding. Device symbol M4000 Advanced (sender or receiver), M4000 Advanced (A/P) or M4000 Area (sender or receiver), context menu Open device window, parameter node General. © SICK AG • Industrial Safety Systems • Germany • All rights reserved…
-
Page 41: Application Diagnostic Output (Ado)
(receiver), context menu Open device window, parameter node General. With external device monitoring activated, the OSSD status function cannot be configured as active LOW. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice…
-
Page 42: Scanning Range
The scanning ranges with deflector mirrors given apply for beam deflections between 80° and 110°. © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 43: Scanning Range Of The M4000 Advanced
5.4.1 Scanning range of the M4000 Advanced You can set the M4000 Advanced multiple light beam safety device to two different scan- ning ranges. The effective scanning range is dependent here upon the dimension of the light path between sender and receiver and the number of deflector mirrors and additional front screens used.
-
Page 44: Scanning Range Of The M4000 Advanced A/P
Device symbol M4000 Advanced (A/P), context menu Open device window, parameter node General. The maximum effective scanning range is dependent here on the number of deflections between the M4000 Advanced A/P and the M4000 Passive and the number of additional front screens used (see Tab. 16). Tab. 16: Maximum effective…
-
Page 45: Scanning Range Of The M4000 Area 60/80
On the utilisation of this protective field width, it must be expected the orange LED will illuminate (cleaning or realignment required). The system then only has a reserve of 30 %. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice…
-
Page 46: External Device Monitoring (Edm)
“External device monitoring (EDM)” on page 86. Device symbol M4000 Advanced (receiver), M4000 Advanced (A/P) or M4000 Area (receiver), context menu Open device window, parameter node General. © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 47: Sender Test
Chapter 5 M4000 Adv., Adv. A/P, Area Sender test The function Sender test is not available with the M4000 Advanced A/P. Note The M4000 sender has a test input on pin 3 for checking the sender and the related receiver. During the test, the sender no longer emits light beams.
-
Page 48: Configurable Muting Functions
The person who makes the change is also responsible for the correct protective function of the device. When making configuration changes, please always use the password hierar- chy provided by SICK to ensure that only authorised persons make changes to the configu- ration. The SICK service team is available to provide assistance if required.
-
Page 49
Information on the possible combinations of additional signal C1 and on connection can be found in section 6.10 “Combinable muting functions and facilities for connecting” from page 63. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice… -
Page 50: Sensor Test
Tab. 21: Output signals of Non-testable sensors output Status non-testable sensors HIGH Activated, material detected Deactivated, no material detected © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 51: Time Monitoring
In combination with the Exit monitoring function use the End of muting by ESPE function. Device symbol M4000 Advanced (receiver) or M4000 Advanced (A/P), context menu Open device window, parameter node Muting configuration. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice…
-
Page 52: Sensor Gap Monitoring
ESPE is monitored. Configure belt stop by allocating the signal for belt stop to the related connection using drag and drop. Device symbol M4000 Advanced (receiver) or M4000 Advanced (A/P), context menu Open device window, parameter node I/O configuration.
-
Page 53: End Of Muting By Espe
You can use the Exit monitoring function if material is allowed to move out of the hazard- ous area while a person is however not allowed enter. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice…
-
Page 54
ESPE function or configure the Total muting time. Device symbol M4000 Advanced (receiver) or M4000 Advanced (A/P), context menu Open device window, parameter node Muting configuration. © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice… -
Page 55: Direction Detection
Device symbol M4000 Advanced (receiver) or M4000 Advanced (A/P), context menu Open device window, parameter node Muting configuration. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice…
-
Page 56: Partial Blanking
The partial blanking is not signalled by the muting lamp. Device symbol M4000 Advanced (receiver), context menu Open device window, para- meter node Muting configuration and parameter node Partial blanking. © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 57: Partial Blanking/Muting Changeover
Tab. 25: Selection of the type Input C1 Type of muting of muting as a function of the Partial blanking/muting input signal Partial blanking HIGH Muting 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice…
-
Page 58
63. Device symbol M4000 Advanced (receiver) or M4000 Advanced (A/P), context menu Open device window, parameter node Muting configuration. © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice… -
Page 59: Override
Override +24 V DC EDM (PIN 6) +24 V DC OSSD1 (PIN 3) +24 V DC OSSD2 (PIN 4) Key-operated switch 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice…
-
Page 60: Override Realised With The Integrated Override Function
UE403 or sens:Control device. Configure override by allocating a control switch for reset/override to the related connection using drag and drop. Device symbol M4000 Advanced (receiver) or M4000 Advanced (A/P), context menu Open device window, parameter node I/O configuration.
-
Page 61
If the permissible number of override statuses has been exceeded, the system changes to the lock4out status and the 7Esegment display indicates the error message 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice… -
Page 62: Monitoring The Muting Lamp
Device symbol M4000 Advanced (receiver) or M4000 Advanced (A/P), context menu Open device window, parameter node Muting configuration. © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 63: Combinable Muting Functions And Facilities For Connecting
11 of M4000 cannot be used in an IP 67 environment. It is only possible to connect Reset/Override (combined) on the M4000 in conjunction with an UE403 or sens:Control device. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice…
-
Page 64: Mounting
The applicable legal and official regulations apply to the use and mounting of the protec- Note tive device. These regulations vary depending on the application. © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 65: Minimum Distance To The Hazardous Area
Height of the hazardous area Hazar- dous point Direction of approach M4000 Height of the beams above the floor 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice…
-
Page 66
T = 290 ms + 30 ms = 320 ms = 0,32 s S = 1600 × 0,32 + 1100 = 1612 mm © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice… -
Page 67
Fig. 36: Minimum distance to the hazardous point for non- perpendicular approach M4000 Direction of approach M4000 Parallel approach Angular approach 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice… -
Page 68: Minimum Distance To Reflective Surfaces
Field of view Minimum distance a Distance D sender–receiver The field of view of the sender and receiver optics is identical. Note © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 69: Steps For Mounting The Device
Fig. 39: Sender and receiver must not be rotated 180° with respect to each other 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice…
-
Page 70
Mounting with Omega bracket Mounting with swivel mount bracket Mounting with side bracket Mounting with rigid mounting bracket Mounting with pivoting mounting bracket © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice… -
Page 71: Mounting With Omega Bracket
The safety light curtain can be mounted and also subsequently adjusted using just one screw. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice…
-
Page 72: Mounting With Swivel Mount Bracket
Higher torques can damage the bracket; lower torques provide inadequate protection against vibration. Fig. 43: Composition of the swivel mount bracket Part No. 2030510 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 73
The multiple light beam safety device can then also be adjusted later. The mounting screw is not included in the delivery. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice… -
Page 74: Mounting With Side Bracket
Attach the bolts of the side bracket with a torque of between 5 and 6 Nm. Higher Notes torques can damage the bracket; lower torques provide inadequate protection against vibration. © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 75
When mounting the bracket, note the distance and the position of the sliding nuts as described in chapter 13.3 “Dimensional drawings” on page 120f. The mounting screw is not included in the delivery. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice… -
Page 76: Mounting With Rigid Mounting Bracket
The alignment of the sender and receiver can be corrected after mounting using only the slots. Fig. 47: Rigid mounting bracket Part No. 7021352 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 77
When mounting the bracket, note the distance and the position of the sliding nuts as described in chapter 13.3 “Dimensional drawings” on page 120f. The mounting screw is not included in the delivery. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice… -
Page 78: Mounting With Pivoting Mounting Bracket
Tighten the bolts on the pivoting mounting bracket to a torque of between 5 and 6 Nm. Note Higher torques can damage the bracket; lower torques provide inadequate protection against vibration. © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 79
When mounting the bracket, note the distance and the position of the sliding nuts as described in chapter 13.3 “Dimensional drawings” on page 120f. The mounting screw is not included in the delivery. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice… -
Page 80: Electrical Installation
0 V connections of the loads and those of the corresponding pro- tective device. © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 81
(see page 83) Extension – connection (see page 84) (see page 84) Configuration connection (see page 85) (see page 85) (see page 85) 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice… -
Page 82: System Connection M26 × 11 + Fe
FE Green Functional earth Functional earth For the connection of pin 9 and 10 only use cable with twisted cores, e.g. the SICK con- Notes nection cables available as accessories (see section 14.7 “Accessories” on page 139). If the UE403 safety relay is used on the extension connection of the M4000, then only SICK sens:Control devices may be connected to pin 9 and pin 10 (EFI device communication) of the system connection.
-
Page 83: M4000 Area 60/80
FE Green Functional earth Functional earth For the connection of pin 9 and 10 only use cable with twisted cores, e.g. the SICK con- Notes nection cables available as accessories (see section 14.7 “Accessories” on page 139). If you do not use either a UE403 or a sens:Control device on the system connection…
-
Page 84: Extension Connection M12 × 4 + Fe For Ue403
If the UE403 safety relay is used on the extension connection of the M4000, then only Note SICK sens:Control devices may be connected to pin 9 and pin 10 (EFI device communica- tion) of the system connection. © SICK AG • Industrial Safety Systems • Germany • All rights reserved…
-
Page 85: Configuration Connection M8 × 4 (Serial Interface)
Pin 3 0 V DC (voltage supply) Pin 5 Pin 2 The pin assignment of sender, receiver and M4000 Advanced A/P is identical. Note After configuration always remove the connecting cable from the configuration connec- tion! After the configuration of the device has been completed, locate the attached protec- tion cap to cover the configuration connection.
-
Page 86: External Device Monitoring (Edm)
If you later deselect the EDM option, pin 6 of the system plug must not remain connec- ted to 24 V. © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 87: Reset Button
Pin 8 of the system connection can be used as Reset required output (24 V). The output has a frequency of 1 Hz. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice…
-
Page 88: Application Diagnostic Output (Ado)
If you use the application diagnostic output as an alarm signal for “Reset required”, it has a frequency of 1 Hz. Only M4000 Advanced and M4000 Advanced A/P in conjunction with a UE403 or sens:Control device: If you connect the application diagnostic output as an alarm signal for muting or over- ride status, then the application diagnostic output will always signal the alarm with an active HIGH.
-
Page 89: Test Input (Sender Test)
The sender test is performed when 0 V is present at the test input (pin 3) of the sender. To be able to use the sender test button, you must also configure the Sender test function with the aid of the CDS: device symbol M4000 Advanced (sender), context menu Open device window, parameter node General.
-
Page 90: Commissioning
AR60 + adapter for M4000 (see section 14.7 “Accessories” on page 139) On this topic read the description in the operating instructions for the “Alignment aid AR60”. © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 91: Meaning Of The 7Esegment Display During Alignment
No indication and The alignment is now true; the devices must be locked in this green LED position. illuminated on the receiver 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice…
-
Page 92
No indication and The alignment is now true; the devices must be locked in this green LED position. illuminated. © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice… -
Page 93: Aligning Sender And Receiver
Switch the power supply to the multiple light beam safety device on. Watch the alignment information on the 7Esegment display of the receiver. Correct the alignment of the sender and receiver (or of the M4000 Advanced A/P and the M4000 Passive), until the 7Esegment display goes off.
-
Page 94: Special Aspects Of Alignment With Deflector Mirrors
The alignment tolerance will become smaller with each further deflection (see Fig. 62). Always use an alignment aid when aligning the M4000 Advanced with deflector mirrors Recommendation (see section “Alignment aids” on page 90).
-
Page 95: Alignment Of The M4000 Advanced With Integrated Laser Alignment Aid (Optional)
Laser Notice No. 50, June 24, 2007 The M4000 Advanced multiple light beam safety device is available with an integrated laser alignment aid as an extra. The laser alignment aid in conjunction with the indications on the 7Esegment display enables you to precisely adjust and align the multiple light beam safety device.
-
Page 96
Operating Instructions M4000 Adv., Adv. A/P, Area In the delivery with the receiver for the M4000 Advanced with integrated laser align- ment aid you will find two self-adhesive alignment templates (one template for the deflector mirror and one for the sender). Keep both alignment templates at hand. You will find further information on the alignment templates as well as a master for copying in the annex 15.3. -
Page 97
(see Fig. 66). The optimal alignment is achieved when the alignment beam is incident in the middle of the rectangular hole in the alignment template. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice… -
Page 98
Transparent display screen Laser beam Laser deflector mirror The display screen illuminates when the laser beam is incident on it. © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice… -
Page 99
(see Tab. 37). All alignment templates used must be removed after the alignment procedure! Note 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice… -
Page 100: Test Notes
© SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 101: Daily Functional Checks Of The Protective Device
– immediately in front of the M4000 Advanced A/P – in the middle between M4000 Advanced A/P and M4000 Passive or another mirror deflection (e.g. deflector mirror PSK45) – immediately in front of the M4000 Passive or another mirror deflection (e.g. deflector mirror PSK45) –…
-
Page 102
M4000 system (e.g. correct mounting of mechanical protective devices). Check whether the protective device is effective for the set operating mode. © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice… -
Page 103: Configuration
To configure the device, please read the user manual for the CDS (Configuration & Diag- nostic Software) and use the online help function of the programme. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice…
-
Page 104: Care And Maintenance
Static charges cause dust particles to be attracted to the front screen. You can prevent Note this effect by using the antistatic plastic cleaner (SICK Part No. 5600006) and the SICK lens cloth (SICK Part No. 4003353). How to clean the front screen: Use a clean and soft brush to remove dust from the front screen.
-
Page 105: Fault Diagnosis
If you cannot remedy an error with the help of the information provided in this chapter, please contact your local SICK representative. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice…
-
Page 106: Error Displays Of The Leds
No operating Check the voltage supply and Green nor the green voltage, or voltage activate, if necessary. LED lights up too low © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 107: Error Displays Of The 7Esegment Display
(see Tab. 26 on page 61) This error display only occurs in conjunction with a UE403 or a sens:Control device. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice…
-
Page 108
1 If the error continues to occur: Check the contactor. Replace, if necessary. Check the wiring for short-circuit to 0 V. © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice… -
Page 109
3 seconds. If the error continues to occur: Check whether the machine-side EDM is connected but not activated in the configuration. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice… -
Page 110
This error display only occurs in conjunction with a UE403 or a sens:Control device. © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice… -
Page 111
If override is configured, Override required is $ » lamp displayed. Check the muting lamp. If necessary, replace them. Verify that the muting lamp is connected correctly. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice… -
Page 112: Extended Diagnostics
Carry out a diagnostics on the M4000 Advanced receiver. Device symbol M4000 Advanced (sender or receiver), M4000 Advanced (A/P) or M4000 Area (sender or receiver), context menu Diagnostics, Display. © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 113: Technical Specifications
Resolution, depending on type M4000 Area 60/80 60 mm 80 mm For detailed information on the safety design of your machine/system, please contact your local SICK representative. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved…
-
Page 114
The system then only has a reserve of 30 %. The scanning range of the M4000 Advanced A/P device must be configured to suit the deflection used (see section 5.4.3 “Scanning range of the M4000 Advanced A/P” on page 44). -
Page 115
LOW. A FPLC (fail-safe programmable logic controller) must be able to identify this status. The maximum rated load inductance is higher with lower switching sequence. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice… -
Page 116
Without OSSDs, without ADO, without Reset required and without UE403. As per IEC 61 131-2. Applies to the voltage range between –30 V and +30 V. © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice… -
Page 117
Below –10 °C the availability of the alignment laser is limited. Depending on load, power supply and wire cross-section. The technical specifications must be observed. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice… -
Page 118
TBBPA M4000 Passive Housing cross-section 52 mm × 55.5 mm Weight, type-dependent See section 13.2 “Table of weights” on page 119ff. © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice… -
Page 119: Table Of Weights
4010 3795 1350 M40#-67A###### 4465 4230 1500 M40#-68A###### 4915 4660 1650 M40#-69A###### 5370 5095 1800 M40#-70A###### 5825 5515 M4000 Advanced A/P. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice…
-
Page 120: Dimensional Drawings
M12 with 10.5 cable (right, only on receiver) Optional (receiver only): Sliding nut groove for side mounting Design with integrated © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 121
[mm] [mm] 1043 1072 If you use the M4000 Advanced (or the M4000 Advanced A/P) with optional end cap with Note integrated LED, the dimension L2 of the receiver increases by 25 mm. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved… -
Page 122: M4000 Passive
M4000 Passive (mm) 27.5 14.5 14.5 M4000 Passive M4000 Passive (mirror deflection) (fibre4optic deflection) 10.5 Sliding nut groove for side mounting © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 123
[mm] beams 1035 1064 If you use a two-beam M4000 Advanced A/P, then instead of the M4000 Passive you can Note use one of the following alternatives: two deflector mirrors PSK45 (see section 13.3.10 “Deflector mirror PSK45” on page 129) one mirror column (part number: 1041917, see section 14.5 “Deflector mirrors and… -
Page 124: M4000 Area 60/80
M4000 Area 60 M4000 Area 80 10.5 Sliding nut groove for side mounting Cable socket M26 with crimp contacts (for DIN 43 651) © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 125: Omega Bracket
1350 1587 1616 1500 1737 1766 1650 1887 1916 1800 13.3.4 Omega bracket Fig. 72: Omega bracket (mm) Part No. 2044846 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice…
-
Page 126: Swivel Mount Bracket
(mm) 12.5 Part No. 2030510 13.3.6 Side bracket Fig. 74: Dimensional drawing side bracket (mm) 34.5 Part No. 2019506 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 127: Rigid Mounting Bracket
±1 Part No. 7021352 13.3.8 Pivoting mounting bracket Fig. 76: Dimensional drawing pivoting mounting bracket 11.5 (mm) 22.5 Part No. 2017751 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice…
-
Page 128: Deflector Mirror Pns75E008
Take the necessary organisational measures to avoid the formation of droplets on the deflector mirrors. The mounting kit is included in the delivery of the deflector mirror PNS75E008. © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 129: Deflector Mirror Psk45
±0.5 73.5 (61) Part No. 5306053 If you use a two-beam M4000 Advanced A/P, then you can use two PSK45 deflector Notes mirrors instead of the M4000 Passive. The deflector mirror PSK45 is not suitable for column mounting. When using deflector mirrors, the effective scanning range is reduced (see Tab. 16 on page 44).
-
Page 130: Ordering Information
M40E-034003RB0 M40S-034503AA0 M40E-034503RB0 M40S-042203AA0 M40E-042203RB0 M40S-043003AA0 M40E-043003RB0 M40S-052203AA0 M40E-052203RB0 M40S-062203AA0 M40E-062203RB0 M40S-072203AA0 M40E-072203RB0 M40S-082203AA0 M40E-082203RB0 Receiver only: extension connection for UE403. © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 131
LED M40S-025013AA0 M40E-025033RB0 M40S-026013AA0 M40E-026033RB0 M40S-034013AA0 M40E-034033RB0 M40S-034513AA0 M40E-034533RB0 M40S-043013AA0 M40E-043033RB0 Receiver only: extension connection for UE403. Receiver only. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice… -
Page 132: Default Delivery Status
M40Z-043003TB0 1027908 PSD02-2301 With mirror deflection (max. effective scanning range 7.5 m). With fibre-optic deflection (max. effective scanning range 4.5 m). © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 133: Default Delivery Status
Application diagnostic output (ADO) Contamination With mirror deflection (max. effective scanning range 7.5 m). With fibre-optic deflection (max. effective scanning range 4.5 m). 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice…
-
Page 134: M4000 Area 60/80
M40E-63A005RA0 M40S-64A005AA0 M40E-64A005RA0 M40S-65A005AA0 M40E-65A005RA0 1050 M40S-66A005AA0 M40E-66A005RA0 1200 M40S-67A005AA0 M40E-67A005RA0 1350 M40S-68A005AA0 M40E-68A005RA0 1500 M40S-69A005AA0 M40E-69A005RA0 1650 M40S-70A005AA0 M40E-70A005RA0 1800 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 135: Default Delivery Status
Activated Scanning range M4000 Area 60 – 0.5-6 m M4000 Area 80 – 0.5-20 m Application diagnostic output (ADO) – Contamination 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice…
-
Page 136: Additional Front Screen (Weld Spark Guard)
2 pieces, suitable for: M40#-62####### Additional front screen for M4000, including sliding nuts and fixing 2033238 screws, 2 pieces, suitable for: M40#-63####### © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 137
An additional front screen reduces the scanning range of the system by 8 %. If sender and receiver each use an additional front screen, the scanning range will be reduced by 16 %. 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice… -
Page 138: Deflector Mirrors And Mirror Columns
Suitable for mirror and device columns Omega bracket for device columns, long, 2 pieces 2045736 Steel plug for floor fastening 5308961 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 139: Accessories
Plug straight/socket straight, 1.5 m 6029281 Plug straight/socket straight, 2.0 m 6025931 Plug straight/socket straight, 5.0 m 6029282 Safety relay UE403 (UE403-A0930) 1026287 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice…
-
Page 140
Sliding nuts for mounting bracket/side bracket, 4 pcs 2017550 Alignment template for integrated laser alignment aid 4040263 Only with devices with integrated laser alignment aid. © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice… -
Page 141: Annex
Complete EU declaration of conformity for download: www.sick.com 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice…
-
Page 142: Checklist For The Manufacturer
18. Has the information label for the daily check been attached so that it is easily visible for the operator? This checklist does not replace the initial commissioning, nor the regular inspection by qualified safety personnel. © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice…
-
Page 143: Alignment Templates
Operating Instructions Chapter 15 M4000 Adv., Adv. A/P, Area 15.3 Alignment templates For the alignment of the M4000 Advanced with integrated laser alignment aid you need two alignment templates: alignment template for mirrors alignment template for the sender The alignment templates are in the delivery of the M4000 receiver .
-
Page 144
Laser alignment aid target Circular opening for beam optics Cut line Laser alignment aid target 80 mm Alignment template for mirrors 80 mm © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice… -
Page 145: Alignment Instructions
Annex Operating Instructions Chapter 15 M4000 Adv., Adv. A/P, Area 15.4 Alignment instructions 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice…
-
Page 146
Annex Chapter 15 Operating Instructions M4000 Adv., Adv. A/P, Area Fig. 82: Alignment instructions copying master © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice… -
Page 147: List Of Tables
Tab. 12: Permissible configuration of the restart interlock ……….39 Tab. 13: Possible configuration for the application diagnostic output …….41 Tab. 14: Scanning range of the M4000 Advanced as a function of the number of deflections per beam and the additional front screens ……..43 Tab.
-
Page 148
Tab. 52: Type codes M4000 Advanced with M26 plug and integrated alignment aid ……………………..131 Tab. 53: Type codes M4000 Advanced with M26 plug and end cap with integrated LED…………………….131 Tab. 54: Type codes M4000 Advanced with M26 plug, integrated alignment aid and end cap with integrated LED ……………..131… -
Page 149: List Of Illustrations
End cap with integrated LED……………….19 Fig. 11: Status indicators of the sender …………….20 Fig. 12: Status indicators of the receiver or of the M4000 Advanced A/P …….21 Fig. 13: Safety on mounting the muting sensors …………..22 Fig. 14: Schematic illustration of muting…………….23 Fig.
-
Page 150
Dimensional drawing M4000 Passive (mm) …………122 Fig. 71: Dimensional drawing M4000 Area 60/80 receiver, sender mirror image (mm)……………………124 Fig. 72: Omega bracket (mm) ………………..125 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice… -
Page 151
Illustration of the alignment templates …………… 143 Fig. 81: Alignment templates copying master…………..144 Fig. 82: Alignment instructions copying master …………… 146 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved Subject to change without notice… -
Page 152
Phone +386 (0)1-47 69 990 E-Mail ghk@sick.com.hk E-Mail office@sick.si Hungary South Africa Phone +36 1 371 2680 Phone +27 11 472 3733 More representatives and agencies E-Mail office@sick.hu E-Mail info@sickautomation.co.za at www.sick.com SICK AG | Waldkirch | Germany | www.sick.com…
6
© SICK AG • Industrial Safety Systems • Germany • All rights reserved
Contents
13 Technical specifications ………………………………………………………………………………….113
13.1
Data sheet……………………………………………………………………………………………113
13.2
Table of weights……………………………………………………………………………………119
13.2.1
13.2.2
M4000 Passive…………………………………………………………………….119
13.2.3
M4000 Area 60/80………………………………………………………………119
13.3
Dimensional drawings …………………………………………………………………………..120
13.3.1
13.3.2
M4000 Passive…………………………………………………………………….122
13.3.3
M4000 Area 60/80………………………………………………………………124
13.3.4
Omega bracket …………………………………………………………………….125
13.3.5
Swivel mount bracket ……………………………………………………………126
13.3.6
Side bracket …………………………………………………………………………126
13.3.7
Rigid mounting bracket …………………………………………………………127
13.3.8
13.3.9
13.3.10
Deflector mirror PSK45 …………………………………………………………129
14 Ordering information ……………………………………………………………………………………….130
14.1
M4000 Advanced …………………………………………………………………………………130
14.1.1
Delivery………………………………………………………………………………..130
14.1.2
Type code …………………………………………………………………………….130
14.1.3
Default delivery status…………………………………………………………..132
14.2
M4000 Advanced A/P…………………………………………………………………………..132
14.2.1
Delivery………………………………………………………………………………..132
14.2.2
Type code …………………………………………………………………………….132
14.2.3
Default delivery status…………………………………………………………..133
14.3
M4000 Area 60/80………………………………………………………………………………134
14.3.1
Delivery………………………………………………………………………………..134
14.3.2
Type code …………………………………………………………………………….134
14.3.3
Default delivery status…………………………………………………………..135
14.4
14.5
14.6
Device columns ……………………………………………………………………………………138
14.7
Accessories ………………………………………………………………………………………….139
15 Annex………………………………………………………………………………………………………………141
15.1
15.2
15.3
Alignment templates …………………………………………………………………………….143
15.4
Alignment instructions…………………………………………………………………………..145
15.5
List of tables ………………………………………………………………………………………..147
15.6
List of illustrations ………………………………………………………………………………..149
Operating Instructions
M4000 Adv., Adv. A/P, Area
8010797/YT72/2016-02-19
Subject to change without notice
Sick m4000 manual pdf
SICK AG Industrial Safety Systems Germany All rights reserved.
These operating instructions contain the following information on
the M4000multiple.OPERATING INSTRUCTIONS. SICK AG Industrial Safety
Systems Germany All rights reserved.You can find more detailed data
in
the operating instructions.
sick m4000 advanced ap manual
Download at www.mysick.com. General data system part sender.
sick m4000 user manual
Receiver.Product description. The M4000 Advanced multiple light
beam. You can find more applications using the application finder
atwww.sick.com. Provides access.Made by SICK. Muestra resumen de
las propiedades del equipo en PDF.MOUNTING INSTRUCTIONS.
sick m4000 manual
SICK AG Industrial Safety Systems.
sick m4000 installation manual
Germany www.sick.com.
sick m4000 manual pdf
80135272011-05-11.The standards and directives cited in these
operating instructions might have changed. 10 109 in connection
with M4000Advanced. SICK . M4000.PRODUCT CATALOG INDUSTRIAL
SAFETY
SYSTEMS SICK.
sick m4000 standard light curtain manual
Instructions, technical information, customer.M4000 A dvanced.
Data, CAD design models, operating instructions, software,
applicationexamples.Sick PinPoint Light Spot Technology, Highly
Visible, Tightly Focussed, Homogenous Red.
sick m4000 standard ap manual
SICK — AUNZ Factory Logistics Automation Short Form
Catalogue.LES ESSENTIELS SICK. Only if customers recognize the
added value ofproducts. At SICK, we sell not only sensors. Safety
devices of the M4000 product family in the.
sick m4000 advanced manual
Providing extra service to the customer, SICK checked and
cleared.of intelligent sensor systems, SICK has been making a
significant contributionto. M4000 Advanced multiple light beam
safety.SICK AG — Industrial Safety Systems — Germany.
sick m4000 light curtain user manual
All rights including changes to technical specification and or
to the equipment without prior notification, are.M4000 estndar.
Bsquedas rpidas yseguras en lnea con los Buscadores de SICK.
Ajuste: botn Teach-in, cable, botn por etapas — manual. SICK —
Industrial Safety Systems GB.
http://dzaipdf.ru/pdf4?id=sick m4000 manual
pdfhttp://dzaipdf.ru/pdf4?id=sick m4000 manual pdf
SICK laser scanners Safety camera systems Safety
controllers.SICK AG — Industrial Safety Systems — Germany. You can
find further data in theoperating instructions.
sick m4000 light curtain manual
M4000 Advanced Curtain.SICK AG — Industrial Safety Systems —
Deutschland. nderungen der technischen Daten und Ausfhrungen der
Gertebleiben vorbehalten.
http://dzaipdf.ru/pdf4?id=sick m4000 manual pdf
Sick m4000 manual pdfsick m4000 advanced ap manualsick m4000
user manualsick m4000 manualsick m4000 installation manualsick
m4000 manual pdfsick m4000 standard light curtain manualsick m4000
standard ap manualsick m4000 advanced manualsick m4000 light
curtain user manualsick m4000 light curtain manual
-
61, Operating Instructions Chapter 7 M4000 Adv., Adv. A/P, Area 8010797/PA53/27-06-05 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 61 Commissioning 7.3 Test notes The purpose of the tests described in the following is to confirm the safety requirements specified in the national/international rules and regulations, especially the safety…
-
42, Chapter 5 Operating Instructions M4000 Adv., Adv. A/P, Area 42 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/PA53/27-06-05 Mounting When mounting the pivoting mounting bracket ensure that the bolts marked , , and remain accessible, allowing you later to adjust and lock the multiple light beam safety device in position. When mountin…
-
46, Chapter 6 Operating Instructions M4000 Adv., Adv. A/P, Area 46 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/PA53/27-06-05 Electrical installation Pin Wire colour Sender Receiver 9 Black Device communication (EFI A ) Device communication (EFI A ) 10 Purple Device communication (EFI B ) Device communication (EFI B ) 11 Grey/p…
-
101, Operating Instructions Chapter 13 M4000 Adv., Adv. A/P, Area 8010797/PA53/27-06-05 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 101 Annex 13.2 Manufacturer’s checklist Checklist for the manufacturer/installer for the installation of electro-sensitive protective equipment (ESPE) Details about the points listed below must be present at least d…
-
8, Chapter 1 Operating Instructions M4000 Adv., Adv. A/P, Area 8 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/PA53/27-06-05 About this document LED symbols describe the status of an LED: The LED is constantly illuminated. The LED is flashing. The LED is off. Instructions for taking action are shown by an arrow. Read carefully and follow the instruc…
-
25, Operating Instructions Chapter 4 M4000 Adv., Adv. A/P, Area 8010797/PA53/27-06-05 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 25 Configurable functions • Additional front screens (SICK accessories see page 95) reduce the effective scanning range. • Deflector mirrors (see page 88f.) reduce the effective scanning range. It is de…
-
52, Chapter 7 Operating Instructions M4000 Adv., Adv. A/P, Area 52 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/PA53/27-06-05 Commissioning 7 Commissioning WARNING Commissioning requires a thorough check by qualified personnel! Before you operate a system protected by the M4000 multiple light beam safety device for the first time, make sure that …
-
107, Operating Instructions Chapter 13 M4000 Adv., Adv. A/P, Area 8010797/PA53/27-06-05 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 107 Annex Tab. 33: Dimensions of the M4000 Area 60/80, dependent of the length of the monitored area …………………………………………………………………………………………..85 Tab. 34: Dimensio…
-
34, Chapter 5 Operating Instructions M4000 Adv., Adv. A/P, Area 34 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/PA53/27-06-05 Mounting How to determine the minimum distance from reflective surfaces: Determine the distance D [m] sender–receiver. Read the minimum distance a [mm] in the diagram or calculate it using the related formula in Ta…
-
36, Chapter 5 Operating Instructions M4000 Adv., Adv. A/P, Area 36 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/PA53/27-06-05 Mounting Sender and receiver can be mounted in four different ways: • mounting with swivel mount bracket • mounting with side bracket • mounting with rigid mounting bracket • mounting with pivoting mounting bracket 5.2.1 Mountin…
-
98, Chapter 12 Operating Instructions M4000 Adv., Adv. A/P, Area 98 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/PA53/27-06-05 Ordering information 12.6 Device columns Description Part number Device column with front plate, incl. mounting kit Suitable for M40#-02500#### and M40#-02501####, [email protected], 500 mm beam separation 2031438 Device column …
-
35, Operating Instructions Chapter 5 M4000 Adv., Adv. A/P, Area 8010797/PA53/27-06-05 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 35 Mounting Observe the safety distance of the system during mounting. On this subject read chapter 5.1 “Determining the safety distance” on page 30. Mount the multiple light beam safety device such that the risk of failu…
-
27, Operating Instructions Chapter 4 M4000 Adv., Adv. A/P, Area 8010797/PA53/27-06-05 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 27 Configurable functions M4000 Area 60 You can set the M4000 Area 60 multiple light beam safety device to two different scanning ranges. The effective scanning range is dependent here upon the dimension of the light path bet…
-
56, Chapter 7 Operating Instructions M4000 Adv., Adv. A/P, Area 56 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/PA53/27-06-05 Commissioning 7.2.4 Alignment of the M4000 Advanced with integrated laser alignment aid (optional) WARNING Never look directly into the laser beam! If the laser beam falls on your eye, you must consciously close your eyes …
-
89, Operating Instructions Chapter 11 M4000 Adv., Adv. A/P, Area 8010797/PA53/27-06-05 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 89 Technical specifications 11.3.9 Deflector mirror PSK45 • If you use a two-beam M4000 Advanced A/P, then you can use two PSK45 deflector mirrors instead of the M4000 Passive. • The deflector mirror P…
Table of Contents for SICK M4000 Advanced:
-
Operating Instructions Chapter 13 M4000 Adv., Adv. A/P, Area 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 125 Subject to change without notice Technical specifications Length of the monitored area S [mm] Dimension L1 [mm] Dimension L2 [mm] 300 387 416 450 537 566 600 687 716 750 8 37 866 900 987 1016 1050 1137 1166 1200 1287 1316 1350 1437 1466 1500 1587 1616 1650 173
-
Chapter 11 Operating Instructions M4000 Adv., Adv. A/P, Area 104 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice Care and maintenance 11 Care and maintenance T he M4000 multiple light beam safety device is maintenance-free. The front screen of the M4000 multiple light beam safety device should be regularly cleaned and also if contami- nated. Do not use aggressive detergents. Do not use abrasive cleaning agents
-
Chapter 13 Operating Instructions M4000 Adv., Adv. A/P, Area 118 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice Technical specifications Minimum Typical Maximum Environmental data, materials Housing Aluminium alloy ALMGSI 0.5 (powder coated) Front screen Polycarbonate, scratch-resistant coating End caps Polyamide 6.6 CF30 Packaging Corrugated cardboard with polyethylene inlays Circuit boards Glass-f
-
Chapter 4 Operating Instructions M4000 Adv., Adv. A/P, Area 36 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice Muting 4.2.6 Muting with four sensors (two sensor pairs), parallel placement In the example, the material moves from left to right. As soon as the first muting sensor pair A1 & A2 is activated, the protection provided by the protective device (ESPE) is muted. The protection remains muted until th
-
Operating Instructions Chapter 5 M4000 Adv., Adv. A/P, Area 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 45 Subject to change without notice Configurable functions 5.4.4 Scanning range of the M4000 Area 60/80 The scanning range of the M4000 Area 60/80 multiple light beam safety device is depen- dent on the related resolution and the beam separation. Addi
-
Operating Instructions M4000 Adv., Adv. A/P, Area 2 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 8010797/YT72/2016-02-19 Subject to change without notice This document is protected by the law of copyright, whereby all rights established therein remain with the company SICK AG. Reproduction of this document or parts of this document is only permissible within the limits of the legal determination of Copyright Law. Alteration or
-
Operating Instructions Chapter 3 M4000 Adv., Adv. A/P, Area 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 15 Subject to change without notice Product description Principles of operation The M4000 multiple light beam safety device consists of a sender unit and a receiver unit. A distinction should be made between active/active systems and active/passive systems: On the active/active system, sender unit and receiver unit are in separate housings, the sender and the receiver. The light beam
-
Operating Instructions Chapter 7 M4000 Adv., Adv. A/P, Area 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 79 Subject to change without notice Mounting When mounting the pivoting mounting bracket ensure that the bolts marked , , and remain accessible, allowing you later to adjust and lock the multiple light beam safety device in position. When mounting the bracket, note the distance and the position of the sliding nuts as described in chapt
-
Operating Instructions Chapter 7 M4000 Adv., Adv. A/P, Area 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 71 Subject to change without notice Mounting 7.2.1 Mounting with Omega bracket The Omega bracket is made of aluminium. The bracket is designed such that sender and receiver can also be exactly aligned after the installation and mounting of the bracket. Attach the screws of the Omega bracket with a torque of between 2 and 2.5 Nm. Hig
-
Operating Instructions M4000 Adv., Adv. A/P, Area 8010797/YT72/2016-02-19 © SICK AG • Industrial Safety Systems • Germany • All rights reserved 3 Subject to change without notice Contents Contents 1 About this document……………………………………………………………………………………………7 1.1 Function of this document…..
Questions, Opinions and Exploitation Impressions:
You can ask a question, express your opinion or share our experience of SICK M4000 Advanced device using right now.