Skyrc t200 инструкция на русском языке

• Page 1
  T200 AC / DC Dual Balance Charger/Discharger Instruction Manual [Version 1.0]…

• Page 2: Table Of Contents

  Table of Contents Introduction Special Features Warning and Safety Notes Program Flow Chart Explanation of Buttons Power and Battery Connection Charge Operation Lithium Battery Program (LiPo/LiFe/Lilon/LiHV) NiMH/NiCd Battery Program Pb Lead-acid Battery Program Battery Memory Set and Call Out System Setting Battery Voltage Meter Battery Resistance Meter Warning and Error Message…

• Page 3: Introduction

  Introduction Congratulations on your choice of SKYRC T200 AC/DC Dual Balance Charger/Discharger. This unit is simple to use, but the operation of a sophisticated automatic charger such as SKYRC T200 does require some knowledge on the part of the user. These operating instructions are designed to ensure that you quickly become familiar with its functions.

• Page 4
  See the Status of Individual Cells in Balance Charge Mode Balance Lead Socket Switch From Channel A to B or Output Socket Vice Versa Temperature Sensor Port Carrying Handle Smart Ventilation Fan DC Input 11-18V Ventilation Slot AC Input 100-240V · 02 T200…

• Page 5: Special Features

  All the settings can be configured by users. Voltage Calibration (for expert user only) SkyRC T200 allows you to calibrate the voltage directly on the device with a 6S LiPo battery. (For more information please contact us at support@skyrc.cn)

• Page 6
  If the temperature limit is reached, the process will be terminated. * This function is only available by connecting optional temperature probe, which is not included in the package. Processing Time Limit You can also limit the maximum process time to avoid any possible defect. · 04 T200…

• Page 7: Warning And Safety Notes

  3.0-3.3V/cell 2.9-3.2V/cell 2.6-2.9V/cell 3.1-3.4V/cell 0.1-1.1V/cell 0.1-1.1V/cell 1.8V/cell Voltage Be very careful to choose the correct voltage for different types of battery otherwise you may cause damage to the batteries. Incorrect settings could cause the cells to fire or explode. T200 05 ·…

• Page 8
  Always refer to the manual by battery manufacturer about charging methods, recommended charging current and charging time. Especially, the lithium battery should be charged according the charging instruction provided by the manufacturer strictly. · 06 T200…
• Page 9
  This is a memory effect. It is said that NiCd and NiMH batteries are suffering from memory effect. NiCd has more memory effect than NiMH. T200 07 ·…

• Page 10: Program Flow Chart

  [ BATT MEMORY 3 ] SAVE PROGRAM SAVE PROGRAM 2.0A 2.0V (1P) Pb 4.0V (2S ) LOAD…… C:3.3A D:1.5A SAVE…. ENTER ENTER ENTER>3Seconds Pb AGM CHG Pb COLD CHG Pb DISCHARGE 0.1A 2.0V (1P) 0.1A 2.0V (1P) 1.5A 4.0V(2P) · 08 T200…

• Page 11: Explanation Of Buttons

  If you have no request for LiPo Battery program, please press the BATT PROG/STOP button to enter BATT PROGRAM screen. T200 09 ·…

• Page 12: Power And Battery Connection

  Power and Battery Connection 1. Connecting to power source There are two kinds of inputs for SKYRC T200, DC 11-18V and AC 100-240V. AC 100-240V power source connection. 12V DC Battery / DC power supply connection. · 10 T200…

• Page 13
  In the other modes, there is no request to connect the balance wire to the balance socket in the charger. But we suggest to charge your battery in balance mode for better performance. 2) NiMH/NiCd or Pb Battery Connection NiMH T200 11 ·…

• Page 14: Charge Operation

  AGM CHG This mode is for charging AGM battery. This mode is for charging Pb battery in cold days when the temperature is COLD CHG 5 ℃ to -20 ℃. DISCHARGE This mode is for discharging Pb battery. · 12 T200…

• Page 15: Lithium Battery Program (Lipo/Life/Lilon/Lihv)

  INC and DEC to change the value and press START/ ENTER to confirm your setting. START/ENTER Program Start LiPo BALANCE 2.0A 11.1V (3S) Press and hold START/ENTER for 3 seconds to start the program. START/ENTER > 3 Seconds T200 13 ·…

• Page 16
  [ Time: 00: 45: 32 ] 16.8V 2600mAh elapsed time. Program Stop During the charging process, press STOP to stop the charging process. Please scan and watch the tutorial video about how to charge LiPo Video battery in balance mode. Tutorial · 14 T200…
• Page 17
  Temperature probe needs to be connected to show Int. Temp 37°C external temperature. Temp Cut-Off Cut-off temperature. 　　　 Safety Timer Safety timer ON and duration of time in minutes. ON 200min Capacity Cut-Off Capacity cut-off ON and value of the set capacity limit. 5000mAh T200 15 ·…

• Page 18: Nimh/Nicd Battery Program

  Discharge, Re-Peak and Cycle. Selecting the Battery Type: After powering on the T200, press the INC or DEC button repeatedly until you reach the appropriate program for the battery type you wish to charge. For this example we have chosen the “NiMH BATT“ or “NiCd BATT” program. Now press the ENTER button to enter the desired program.

• Page 19
  Follow the instructions provided on your battery when setting the voltage cut-off. The T200 will stop discharging when the battery has reached the preset voltage cut-off. Press and hold the START button for 3 seconds to start NiMH 1.3A 10.42V…
• Page 20
  A five-minute cool-down delay occurs after each re- peak charge. IN RE-PEAK MODE, THE T200 USES THE CHARGE AMPERAGE AND VOLTAGE SETTINGS ENTERED IN CHARGE MODE. After selecting the correct battery type, use the INC or DEC NiMH RE-PEAK button to select the “RE-PEAK”…
• Page 21
  Pressing the START button again will cause the cycle count to begin flashing. Use the INC or DEC button to change this to the number of cycles you want the T200 to run. The T200 can cycle the battery a maximum of 5 times consecutively.

• Page 22: Pb Lead-Acid Battery Program

  Pb Lead-acid Battery Program Additional NiMH/NiCd Process Information: During the NiMH/NiCd battery charging/discharging process the T200 can display a variety of information. Using the INC or DEC buttons, you can also view the following information: Delta Peak Voltage NiMH Sensitivity…

• Page 23
  Press the START button again and the nominal battery pack Pb COLD CHG voltage will begin flashing. Use the INC or DEC button to set 1.5A 12.0V(6P) the voltage and the number of cells. Press and hold the START button for 3 seconds to start charging. T200 21 ·…
• Page 24
  “FINISHED” and the charger will emit a ringing sound. Additional Pb Process Information: During the Pb battery charging/discharging process the T200 can display a variety of information. Using the INC or DEC buttons you can also view the following information:…

• Page 25: Battery Memory Set And Call Out

  T V C = Y O U R R I S K Set the terminal voltage(4.18-4.25V). 4 . 2 0 V DEC INC S A V E P R O G R A M Press ENTER to save program. E N T E R START/ENTER T200 23 ·…

• Page 26
  L O A D L i P o B A L A N C E C H G Press START/ENTER for 3 seconds to start the process. 4 . 9 A 7 . 4 V ( 2 S ) · 24 T200…

• Page 27: System Setting

  Fahrenheit you like. A rest time allowing the battery to cool R e s t T i m e 1-60Min down between charging/discharging C H G > D C H G 1 0 M i n cycle. T200 25 ·…

• Page 28
  L o a d F a c t o r y S e t E n t e r setting. It indicates the hardware and firmware V e r s i o n H W : 1 . 0 0 F W : 1 . 1 0 version. · 26 T200…

• Page 29: Battery Voltage Meter

  The screen indicate the total voltage, the highest M A I N 2 5 . 1 3 V voltage and the lowest voltage. H 4 . 2 0 0 V L 4 . 1 8 2 V T200 27 ·…

• Page 30: Battery Resistance Meter

  The screen indicate each cell’s resistance. 0 0 6 m Ω The screen indicate the total resistance, the highest T A T A L :2 8 mΩ resistance and the lowest resistance. H :1 2 mΩ L :5 mΩ · 28 T200…

• Page 31: Warning And Error Message

  B A T T E R Y W A S F U L L which the user sets when charging in balance mode. N O P O W E R No power allocate to the charger. D I S T R I B U T E D T200 29 ·…

• Page 32: The Set Contains

  The Set Contains THESETCONTAINS 1. SKYRC T200 Charger 2. Power Cord with EMC Ferrite Core 3. Instruction Manual EMC Ferrite Core T200 AC / DC Dual Balance Charger/Discharger Instruction Manual [Version 1.0] RECOMMENDED ACCESSORIES Tamiya Charging Cable Dean Charging Cable…

• Page 33: Specification

  Discharge Cut-off Voltage: NiMH/NiCd: 0.1-1.1V/cell LiPo: 3.0-3.3V/cell LiHV: 3.1-3.4V/Cell LiFe: 2.6-2.9V/cell LiIon: 2.9—3.2V/cell Pb: 1.8-2.0V/cell Discharge Wattage: 10W Balance Cells: 2-6 cells Memory: 10 different charge/discharge profiles Charge Method: CC/CV for lithium types and lead (Pb) batteries Delta-peak Sensitivity for NiMH/NiCd. T200 31 ·…

• Page 34: Conformity Declaration

  Conformity Declaration SkyRC T200 satisfy all relevant and mandatory EC directives and FCC Part 15 Subpart B. Requirements for Household Appliances, electric EN 55014-1:2017 tools, and similar apparatus –Part 1: Emission Electromagnetic compatibility Requirements for Household Appliances, electric EN 55014-2:2015 tools, and similar apparatus –…

• Page 35: Regulatory Information

  – Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCC’s RF exposure guidelines, this equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. T200 33 ·…

• Page 36: Commonly Used Terms

  13.2 volts (4×3.3). If the nominal voltage of the battery is not printed on the battery’s label, consult your battery manufacturer or supplier. Do not guess the rated voltage of battery. · 34 T200…

• Page 37: Warranty And Service

  Liability exclusion This charger is designed and approved exclusively for use with the types of battery stated in this Instruction Manual. SkyRC accepts no liability of any kind if the charger is used for any purpose other than that stated.

• Page 38
  Latest version can be downloaded from www.skyrc.com If you have any question about this document, please contact SkyRC by sending a message to info@skyrc.cn All Rights Reserved. All specifications and figures are subject to change without notice. Printed in China 2019.03…

инструкцияSkyRC T200

Instruction Manual

[Version 1.0]

T200

AC / DC Dual Balance Charger/Discharger

Посмотреть инструкция для SkyRC T200 бесплатно. Руководство относится к категории Зарядные устройства, 2 человек(а) дали ему среднюю оценку 7.5. Руководство доступно на следующих языках: английский. У вас есть вопрос о SkyRC T200 или вам нужна помощь? Задайте свой вопрос здесь

• 页 1
• 页 2
• 页 3
• 页 4
• 页 5
• 页 6
• 页 7
• 页 8
• 页 9
• 页 10
• 页 11
• 页 12
• 页 13
• 页 14
• 页 15
• 页 16
• 页 17
• 页 18
• 页 19
• 页 20
• 页 21
• 页 22
• 页 23
• 页 24
• 页 25
• 页 26
• 页 27
• 页 28
• 页 29
• 页 30
• 页 31
• 页 32
• 页 33
• 页 34
• 页 35
• 页 36
• 页 37
• 页 38

Количество вопросов: 0

показать больше

Не можете найти ответ на свой вопрос в руководстве? Вы можете найти ответ на свой вопрос ниже, в разделе часто задаваемых вопросов о SkyRC T200.

Не нашли свой вопрос? Задайте свой вопрос здесь

Характеристики:

• Размер и вес
• Материал корпуса: пластик
• Размер корпуса: 178x135x96 мм
• Вес: 850 г
• Дисплей
• Тип дисплея: ЖК
• Подсветка дисплея: синий
• Мощность
• Входное напряжение постоянного тока:
• 11-18В Входное напряжение переменного тока: 100-240В
• Мощность зарядки: 100 Вт Х 2
• Мощность разряда: 10 Вт
• Аккумуляторы
• Типы батарей / Элементы:
• LiPo / LiHV / LiFe / LiIon: 1-6 ячеек
• NiMH / NiCd: 1-15 ячеек
• Pb: 2-20 В
• Диапазон емкости батареи:
• NiMH / NiCd: 100-50000
• мАчLiPo / LiIon / LiFe / LiHV: 100-50000 мАч
• Pb: 100-50000 мАч
• Зарядка и разрядка
• Напряжение зарядки
• NiMH / NiCd: обнаружение дельта-пика
• LiPo: 4,18-4,25 В / элемент
• LiFe: 3,58-3,7 В / элемент
• Pb: 1,8-2,0 В / элемент
• LiIon: 4,08-4,2 В / элемент
• LiHV: 4,25-4,35 В / элемент

Напряжение отключения разряда

• NiMH / NiCd: 0.1-1.1V / клетка
• LiPo: 3,0-3,3 В / элемент
• LiFe: 2,6-2,9 В / элемент
• LiIon: 2,9-3,2 В / элемент
• LiHV: 3,1-3,4 В / элемент
• Температура отключения батареи: 20ºC / 68ºF-80ºC / 176ºF (регулируемая)
• Диапазон напряжения чтения: 0.1-26.1V / ячейка
• Ток зарядки: 0,1А-12,0А
• Ток разряда: 0.1A-2.0A
• Ячейки баланса: 2-6 ячеек
• Ток баланса: 500 мА / ячейка
• Таймер безопасности: 1-120 минут выключен
• Метод зарядки:
• CC / CV для литиевых и свинцовых (Pb) аккумуляторов. Дельта-пик Чувствительность для NiMH / NiCd.
• Память: 10 различных профилей заряда / разряда

Магазин RC-TODAY.RU осуществляет доставку заказов как собственной курьерской службой, так и различными транспортными компаниями.

MANUALSCAT | RU

Вопросы и ответы

У вас есть вопрос о SkyRC T200, но вы не можете найти ответ в пользовательском руководстве? Возможно, пользователи ManualsCat.com смогут помочь вам и ответят на ваш вопрос. Заполните форму ниже — и ваш вопрос будет отображаться под руководством для SkyRC T200. Пожалуйста, убедитесь, что вы опишите свои трудности с SkyRC T200 как можно более детально. Чем более детальным является ваш вопрос, тем более высоки шансы, что другой пользователь быстро ответит на него. Вам будет автоматически отправлено электронное письмо, чтобы проинформировать вас, когда кто-то из пользователей ответит на ваш вопрос.