Тонометр омрон м2 классик инструкция на русском языке

Остались вопросы?

Не нашли свой ответ в руководстве или возникли другие проблемы? Задайте свой вопрос в форме ниже с подробным описанием вашей ситуации, чтобы другие люди и специалисты смогли дать на него ответ. Если вы знаете как решить проблему другого человека, пожалуйста, подскажите ему

Часто задаваемые вопросы

Arm Cuffs:

If air starts to leak from the arm cuff, please replace with a new one.

Refer to «6. Optional Parts».

O

Digital Automatic

Blood Pressure Monitor

Model

M2 Classic

Instruction Manual

Medium cuff

O. Medium cuff: arm circumference 22-32 cm

P. Large cuff: arm circumference 32-42 cm

Introduction

2. Preparation

Thank you for purchasing the OMRON M2 Classic Digital Automatic Blood Pressure

Monitor.

2.1 Using the AC Adapter

The OMRON M2 Classic is a fully automatic blood pressure monitor, operating on the

oscillometric principle. It measures your blood pressure and pulse rate simply and quickly.

Notes:

For comfortable controlled inflation without the need of pressure pre-setting or

• Never plug or unplug the power cord with wet hands.

re-inflation the devices uses its advanced «IntelliSense» technology.

• Use only the original AC adapter designed for this unit. Use of

unsupported adapters may damage the unit.

The unit also stores up to 30 measurements in memory.

1.

Insert the AC adapter

Please read this instruction manual thoroughly before using the unit. For specific

information about your own blood pressure, CONSULT YOUR DOCTOR.

plug into the AC adapter

jack on the right side of

Important Safety Information

the main unit.

Consult your doctor prior to using in pregnancy or if diagnosed with arrhythmia

2.

Plug the AC adapter

or arteriosclerosis.

Please read this section carefully before using the unit.

into an electrical outlet.

Warning:

To disconnect the AC adapter, unplug the AC adapter from the electrical outlet

• Indicates a potentially hazardous situation which, if not avoided, could result

in death or serious injury.

first and then immediately remove the AC adapter plug from the main unit.

(General Usage)

• Always consult your doctor. Self-diagnosis of measurement results and

self-treatment are dangerous.

2.2 Installing/Replacing the Batteries

• People with severe blood flow problems, or blood disorders, should consult a

doctor before using the unit, as cuff inflation can cause internal bleeding.

1.

Turn the main unit upside down.

(AC Adapter Usage)

• Never plug in or unplug the power cord from the electric outlet with wet hands.

(Battery Usage)

2.

Slide the battery cover in the direction

• If battery fluid should get in your eyes, immediately rinse with plenty of clean

of the arrow while pressing the ribbed

water. Consult a doctor immediately.

Caution:

part of the cover.

• Indicates a potentially hazardous situation which, if not avoided, may result in minor or

moderate injury to the user or patient or damage to the equipment or other property.

3.

Install or replace four «AAA» size

(General Usage)

• Do not leave the unit unattended with infants or persons who cannot express their consent.

batteries so that the + (positive) and —

• Do not use the unit for any purpose other than measuring blood pressure.

(negative) polarities match the polarities

• Do not disassemble the unit or arm cuff.

• Use only the approved arm cuff for this unit. Use of other arm cuffs may result

indicated on the battery compartment.

in incorrect measurement results.

• Make sure that the air tube is not wrapped around other parts of your body

4.

when taking measurements at night. This could result in injury when the air

Put the battery cover back in place.

pressure in the air tube is increased.

Slide the battery cover as indicated,

• Do not leave the cuff wrapped on the arm if taking measurements during the

until it clicks into place.

night. This could result in injury.

• Do not inflate the arm cuff over 299 mmHg.

• Do not use a mobile phone or other devices that emit electromagnetic fields,

Note: The measurement

near the unit. This may result in incorrect operation of the unit.

• Do not operate the unit in a moving vehicle (car, airplane).

values continue to be

• To inflate the cuff manually, refer to Chapter 3.3. If the cuff is over inflated, it

stored in memory even

can cause internal bleeding.

after the batteries are replaced.

(AC Adapter Usage)

• Use only the original AC adapter designed for this unit. Use of unsupported

2.3 Battery Life & Replacement

adapters may damage and/or may be hazardous to the unit.

• Plug the AC adapter into the appropriate voltage outlet.

If the battery low symbol (

• Do not use the AC adapter if the unit or the power cord is damaged. Turn off

replace all four batteries at the same time.

the power and unplug the power cord immediately.

— When the battery low symbol (

(Battery Usage)

will still be able to use the unit for a short while. You

• If battery fluid should get on your skin or clothing, immediately rinse with

plenty of clean water.

should replace the batteries with new ones as soon as possible.

• Use only four «AAA» alkaline batteries with this unit. Do not use other types of batteries.

— When the symbol (

• Do not insert the batteries with their polarities incorrectly aligned.

batteries with new ones at once. Turn the unit off before replacing the batteries.

• Replace old batteries with new ones immediately. Replace all four batteries at

the same time.

• Remove the batteries if the unit will not be used for three months or more.

• Remove the batteries if the unit will not be used for three months or more.

• Dispose of batteries according to applicable local regulations.

• Do not use new and used batteries together.

General Precautions

Four new «AAA» alkaline batteries will last for approximately 300 measurements,

• Do not apply strong shocks and vibrations to or drop the unit and arm cuff.

when used to take two measurements a day.

• Do not take measurements after bathing, drinking alcohol, smoking,

Since the supplied batteries are for monitoring use only, they may have

exercising or eating.

a shorter life and do not last for 300 measurements.

• Do not forcibly bend the arm cuff or bend the air tube excessively.

• When removing the air tube, pull on the air plug at the connection with the

main unit not the tube itself.

3. Using the Unit

• Do not inflate the arm cuff when it is not wrapped around your arm.

• Do not wash the arm cuff or immerse it in water.

3.1 Applying the Arm Cuff

• Read and follow the «Important information regarding Electro Magnetic

Compatibility (EMC)» in the Technical Data Section.

Be sure to wrap the arm cuff correctly so that you get accurate results.

• Read and follow the «Correct Disposal of This Product» in the Technical Data

Measurements can be taken in light clothing. However, please remove

Section when disposing of the device and any used accessories or optional parts.

thick clothes, such as sweaters, before taking a reading.

Note: You can take a measurement on either your left or right arm. The blood

1. Overview

pressure can differ between the right arm and the left arm and therefore

also the measured blood pressure values can be different. Omron

Main unit:

A

E

recommends to always use the same arm for measurement. If the

values between the two arms differ substantially, please check with your

physician which arm to use for your measurement.

1.

Insert the air plug into the air jack

on the left side of the main unit.

D

F

C

B

2.

Apply the arm cuff to your upper arm. The air tube should be

A. Display

D. AC adapter jack

centred on the inside of your arm and point down the inside of

B. O/I START button

E. Battery compartment

C. M (Memory) button

F. Air jack

the arm, so that the air tube runs down the inside of your

forearm and is in line with your middle finger.

Display:

G

H

I

K

L

J

M

N

3.

When the cuff is positioned correctly, close the fabric fastener firmly.

G.

Systolic blood pressure

L.

Pulse display

Taking a Reading on the Right Arm

H.

Diastolic blood pressure

M.

Deflation symbol

I.

Memory symbol

N. Battery low symbol

Apply the cuff so that the air tube is

(Displayed when viewing

at the side of your elbow.

values stored in memory)

Note: If your systolic or diastolic

J.

Irregular heartbeat symbol

pressure is outside the

Notes:

K.

Heartbeat symbol

standard range

• Be careful not to rest your arm on

1.

Flashes during measurement

(above 135/85 mmHg),

the air tube, or otherwise restrict

2.

If flashing after measurement

the Heartbeat symbol (

)

the flow of air to the cuff.

complete indicates blood pressure

will blink. Refer to

• The cuff should be 1 to 2 cm above

out of recommended range

«3.2 Taking a Reading».

the elbow.

3.2 Taking a Reading

1.

Sit on a chair with your feet flat on

the floor and place your arm on a

P

Q

table so that the arm cuff will be

Q

at the same level as your heart.

Keep still and do not talk during measurement.

2.

Press the O/I START button to turn the unit on.

R

R

Large cuff

Q. Air Tube

R. Air Plug

Note: To cancel a measurement, press the O/I START button to turn the

unit off and to release the air in the arm cuff.

3.

Check the measurement results.

The unit automatically stores blood

pressure and pulse rate into its memory.

Refer to «3.4 Using the Memory

Function».

Notes:

• Self-diagnosis of measured results and treatment are dangerous.

Please follow the instructions of your doctor.

• Wait 2-3 minutes before taking another blood pressure reading.

Waiting between readings allows the arteries to return to the condition prior

to taking the blood pressure measurement.

Important:

• If your systolic or diastolic pressure is outside

the standard range, the heartbeat symbol will

blink when the measurement result is displayed.

Recent research suggests that the following

values can be used as a guide to high blood

pressure for measurements taken at home.

Systolic Blood Pressure

Diastolic Blood Pressure

This criteria is for home blood pressure measurement.

• Your blood pressure monitor includes an irregular

heartbeat feature. Irregular heartbeats can influence

the results of the measurement. The irregular

heartbeat algorithm automatically determines if the

measurement is usable or needs to be repeated.

If the measurement results are affected by irregular

heartbeats but the result is valid, the result is shown together with the

irregular heartbeat symbol ( ).

If the irregular heartbeats cause the measurement to be invalid,

no result is shown. If the Irregular heartbeat symbol ( ) is shown

after you have taken a measurement, repeat the measurement.

If the Irregular heartbeat symbol ( ) is shown frequently, please

make your doctor aware of it.

4.

Remove the arm cuff.

5.

) appears on the display,

Press the O/I START button to turn the unit off.

Note: If you forget to turn the unit off, it will automatically shut itself off after

) starts to blink, you

five minutes.

) remains lit, the batteries are exhausted. You should replace the

What is Irregular Heartbeat?

An irregular heartbeat is a heartbeat rhythm

that varies by more than 25% from the

average heartbeat rhythm detected

while the unit is measuring the systolic

and diastolic blood pressure.

If such an irregular rhythm is detected

more than twice during measurement,

the irregular heartbeat symbol (

)

appears on the symbol when the

measurement results are displayed.

What is Arrhythmia?

A heartbeat is stimulated by electrical signals that cause the heart to contract.

Arrhythmia is a condition where the heartbeat rhythm is abnormal due to flaws in

the bio-electrical system that drives the heartbeat. Typical symptoms are

skipped heartbeats, premature contraction, an abnormally rapid (tachycardia) or

slow (bradycardia) pulse. This can be caused by heart disease, aging, physical

predisposition, stress, lack of sleep, fatigue etc. Arrhythmia can only be

diagnosed by a doctor through a special examination.

Whether the appearance of the irregular heartbeat symbol (

indicates arrhythmia or not can only be determined by an examination and

diagnosis by your doctor.

Warning:

If the irregular heartbeat symbol ( ) is shown frequently, please make your doctor

aware of it. Conducting self-diagnosis and treatment based on measurement

results is dangerous. Be sure to follow the instructions of your doctor.

3.3 Instructions for Special Conditions

If your systolic pressure is known to be more than 170 mmHg, press

and hold the O/I START button until the arm cuff inflates 30 to

40 mmHg higher than your suspected systolic pressure.

1.

Press the O/I START button

1 — 2 cm

to turn the unit on.

Measurement starts.

2.

When the cuff starts to inflate, press the O/I START button

and keep it pressed until the pressure is 30 to 40 mmHg

higher than your suspected systolic pressure.

Note: You cannot inflate the cuff above 299 mmHg. (An error will be displayed

1 to 2 cm

if you try to inflate the cuff above 300 mmHg.)

3.

Release the O/I START button when the cuff has been

inflated to the desired pressure.

The cuff starts to deflate and measurement starts.

4.

The rest of the procedure is the same as for normal

measurement. Refer to «3.2 Taking a Reading», steps 3 to 5.

Note: Do not apply more pressure than necessary.

3.4 Using the Memory Function

This unit has a memory capable of storing 30 sets of readings. Every

time you complete the measurement, the unit automatically stores the

blood pressure and pulse rate.

Note: When 30 sets of readings are stored in memory, the oldest set will be

deleted to store a new set.

1.

Press the Memory (M) button.

The result from the most recent measurement is displayed.

Systolic blood

pressure

Diastolic blood

pressure

Important:

Pulse display

If your systolic or diastolic pressure is

outside the standard range, the heartbeat

symbol will blink when the measurement

result is displayed.

Refer to «3.2 Taking a Reading».

Note:

If there are no measurements results

stored in memory, the screen to the right

is displayed.

2.

Press the Memory (M) button repeatedly to

cycle through the previous measurement

results.

The Memory number appears for a second

before the pulse rate is displayed.

Above 135 mmHg

The newest set is numbered «1».

Above 85 mmHg

At the end of the measurement, if an irregular heartbeat is

detected, the irregular heartbeat symbol will be displayed

with the result.

3.

Press the O/I START button to turn the unit off.

If you forget to turn the unit off, it will automatically shut

itself off after five minutes.

To Delete All the Values Stored in Memory

You cannot delete individual stored readings, all the

readings in the unit will be deleted.

1.

To delete stored readings, first press the Memory (M) button.

Then while holding it down, press the O/I START button

simultaneously for about 2-3 seconds. All readings will

then be deleted.

1

2

2.

Press the O/I START button to turn the unit off.

Irregular Heartbeat

If you forget to turn the unit off, it will automatically shut

itself off after five minutes.

Pulse

Blood

pressure

Irregular Heartbeat

4. Handling Errors and Problems

Short

Long

4.1 Error Messages

Pulse

Blood

Error Display

Cause

Remedy

pressure

Carefully read and repeat the

Cuff is under inflated.

steps listed under section 3.3.

Repeat measurement. Remain

Movement during

still and do not talk during

measurement.

measurement.

) in the results

Insert the air plug securely.

Air plug disconnected.

Refer to section 3.1.

Arm cuff not applied

Apply the arm cuff correctly.

correctly.

Refer to section 3.1.

Clothing is interfering

Remove any clothing

with the arm cuff.

interfering with the arm cuff.

Air is leaking from the

Replace cuff with new one.

arm cuff.

Arm cuff has been

Do not inflate the arm cuff

inflated above

above 299 mmHg.

299 mmHg.

Refer to section 3.3.

Replace all four «AAA»

Battery power is low.

batteries with new ones.

Refer to section 2.2.

Blinks or appears

continuously

Contact your OMRON retail

Device error.

outlet or distributor.

4.2 Troubleshooting

7. Technical Data

Product Description

Problem

Cause

Remedy

Model

Apply the arm cuff

Display

Arm cuff not applied

correctly.

Measurement Method

correctly.

Refer to section 3.1.

Measurement Range

The reading is

Remain still and do not

Movement or talking

Memory

extremely low (or

talk during

during measurement.

measurement.

Accuracy

high).

Remove any clothing

Clothing is interfering

Inflation

interfering with the arm

with the arm cuff.

Deflation

cuff.

Pressure Detection

Make sure that the air

Power Source

The air plug is not

jack is connected

Battery Life

securely inserted into

securely.

Arm cuff pressure

the main unit.

Refer to section 3.1.

does not rise.

Operating Temperature/

Humidity

Air is leaking from the

Replace the arm cuff

Storage Temperature/

arm cuff.

with a new one.

Humidity/ Air Pressure

Apply the cuff correctly

Console Weight

so that it is firmly

Cuff Weight

Arm cuff deflates too

wrapped around the

The arm cuff is loose.

soon.

arm.

Outer Dimensions

Refer to section 3.1.

Cuff Dimensions

Inflate the cuff so that it

Cannot measure or

The arm cuff has not

is 30 to 40 mmHg

above your previous

readings are too low

been inflated

measurement result.

or too high.

sufficiently.

Cuff material

Refer to section 3.3.

Package Content

The unit loses power

The batteries are

Replace the batteries

during measurement.

empty.

with new ones.

Note: Subject to technical modification without prior notice

The batteries are

Replace the batteries

• This OMRON product is produced under the strict quality system of OMRON

empty.

with new ones.

Healthcare Co. Ltd., Japan. The Core component for OMRON blood pressure

Nothing happens

monitors, which is the Pressure Sensor, is produced in Japan.

when you press the

The batteries have

Insert the batteries with

• Disposal of this product and used batteries should be carried out in accordance

buttons.

been inserted

the correct (+/ -)

with the national regulations for the disposal of electronic products.

incorrectly.

polarity.

Press the O/I START button and repeat

measurement.

If the problem continues, try replacing the

Other problems.

batteries with new ones.

If this still does not solve the problem, contact

your OMRON retail outlet or distributor.

This device fulfils the provisions of EC directive 93/42/EEC (Medical Device Directive).

This blood pressure monitor is designed according to the European Standard EN1060,

Non-invasive sphygmomanometers Part 1: General Requirements and Part 3:

Supplementary requirements for electromechanical blood pressure measuring systems.

5. Maintenance and Storage

Please read the instruction manual carefully before

using the device.

Maintenance

Important information regarding Electro Magnetic Compatibility (EMC)

To protect your unit from damage, please observe the following:

With the increased number of electronic devices such as PC’s and mobile

• Do not subject the main unit and cuff to extreme

(cellular) telephones, medical devices in use may be susceptible to

temperatures, humidity, moisture or direct sunlight.

electromagnetic interference from other devices. Electromagnetic

• Do not fold the cuff or tubing tightly.

interference may result in incorrect operation of the medical device and

• Do not inflate the arm cuff over 299 mmHg.

create a potentially unsafe situation.

Medical devices should also not interfere with other devices.

• Do not disassemble the unit.

• Do not subject the unit to strong shocks or vibrations

In order to regulate the requirements for EMC (Electro Magnetic

Compatibility) with the aim to prevent unsafe product situations, the

(for example, dropping the unit on the floor).

EN60601-1-2:2007 standard has been implemented. This standard defines

• Do not use volatile liquids to clean the main unit.

the levels of immunity to electromagnetic interferences as well as maximum

The unit should be cleaned with a soft, dry cloth.

levels of electromagnetic emissions for medical devices.

• Do not wash the arm cuff or immerse it in water.

This medical device manufactured by OMRON Healthcare conforms to this

• Do not use petrol, thinners or similar solvents to clean

EN60601-1-2:2007 standard for both immunity and emissions.

Nevertheless, special precautions need to be observed:

the arm cuff.

• Do not use mobile (cellular) telephones and other devices, which generate

strong electrical or electromagnetic fields, near the medical device. This

may result in incorrect operation of the unit and create a potentially unsafe

situation. Recommendation is to keep a minimum distance of 7 m. Verify

correct operation of the device in case the distance is shorter.

Further documentation in accordance with EN60601-1-2:2007 is available at

• Use a soft, moistened cloth and soap to clean the arm cuff.

OMRON Healthcare Europe at the address mentioned in this instruction manual.

• Do not carry out repairs of any kind by yourself.

Documentation is also available at www.omron-healthcare.com.

If a defect occurs, consult your OMRON distributor.

Correct Disposal of This Product

Calibration and Service

(Waste Electrical & Electronic Equipment)

• The accuracy of this blood pressure monitor has been

This marking shown on the product or its literature, indicates

carefully tested and is designed for a long service life.

that it should not be disposed of, with other household wastes

at the end of its working life. To prevent possible harm to the

• It is generally recommended to have the unit inspected every

environment or human health from uncontrolled waste disposal,

two years to ensure correct functioning and accuracy.

please separate this from other types of wastes and recycle it

Please consult your authorised OMRON dealer.

responsibly to promote the sustainable reuse of material resources.

Storage

Household users should contact either the retailer where they purchased

Keep the unit in its storage case when not in use.

this product, or their local government office, for details of where and how

they can take this item for environmentally safe recycling.

1.

Unplug the air tube from the air jack.

Business users should contact their supplier and check the terms and

conditions of the purchase contract. This product should not be mixed with

Gently fold the air tube

other commercial wastes for disposal.

into the arm cuff.

This product does not contain any hazardous substances.

Note: Do not bend the air tube excessively.

Do not store the unit in the following situations:

Manufacturer

• If the unit is wet.

• Locations exposed to extreme temperatures, humidity, direct sunlight,

dust or corrosive vapours.

• Locations exposed to vibrations, shocks or where it will be at risk of

falling.

EU-representative

6. Optional Parts

Medium arm cuff

Large arm cuff

AC adapter

Arm circumference

Arm circumference

Exclusive

22 — 32 cm

32 — 42 cm

distributor in

Russia & importer

Production Facility

CM-9997579-7

CL-9970672-9

R Adapter-9997605-0

HEM-7117-ALRU_A_M02_090619.pdf

Digital Automatic Blood Pressure Monitor

OMRON M2 Classic (HEM-7117-ALRU)

LCD Digital Display

Oscillometric method

Pressure: 0 mmHg to 299 mmHg

Pulse: 40 to 180/min.

30 Measurements

Pressure: ±3 mmHg

Pulse: ±5% of display reading

Automatic by electric pump

Automatic pressure release valve

Capacitive pressure sensor

4 «AAA» batteries 1.5V or AC/ DC adapter (6V

4W)

Capacity of new alkaline batteries is approx. 300

measurements

10°C to 40°C/ 30 to 85% RH

-20°C to 60°C/ 10 to 95% RH/ 700-1060 hPa

Approximately 289g without batteries

Medium cuff: approximately 120g

Large cuff: approximately 180g

Approximately 114 (w) mm

×

84 (h) mm

×

129 (l) mm

Medium cuff: approximately 146 mm

×

446 mm

(Arm circumference 22 to 32 cm)

Large cuff: approximately 174 mm

×

652 mm

(Arm circumference 32 to 42 cm)

Nylon

Main unit, medium cuff, large cuff, instruction manual,

storage case, battery set, AC adapter, guarantee card,

blood pressure pass

= Type B

OMRON HEALTHCARE CO., LTD.

24, Yamanouchi Yamanoshita-cho, Ukyo-ku, Kyoto,

615-0084, Japan

OMRON HEALTHCARE EUROPE B.V.

Kruisweg 577, 2132 NA Hoofddorp,The Netherlands

www.omron-healthcare.com

ComplectService Ltd.

1/1, Tishinskaya sq, Moscow, Russia,123056

www.csmedica.ru

OMRON DALIAN CO., LTD.

Economic & Technical Development Zone

Dalian 116600, China

Made in China

IM-HEM-7117-ALRU-02-11/09

5327736-0B