Zanussi fl 726 cn инструкция на русском

Инструкция и руководство для
Zanussi FL 726 CN на русском на английском

39 страниц подробных инструкций и пользовательских руководств по эксплуатации

ZMUSSI

WASHING MACHINE

СТИРАЛЬНАЯ МАШИНА

FL 726 CN

r

C

;i4i ^

п7

124972370

INSTRUCTION BOOKLET

РУКОВОДСТВО nO ЭКСПЛУАТАЦИИ

Your new washing machine, A ecological hints, Environment protection

Packaging recycling, Washing machine scrapping, Ecological hints

• Изображение
• Текст

YOUR NEW WASHING MACHINE

This new washing machine meets all

requirements for a modern washing of laundry

with reduced consumption of water, energy and

detergent.

■ The temperature selector dial allows you to

choose personally the suitable washing
temperature for your laundry.

■ The automatic cooling of the washing water

from 95°C to 60°C before draining will

prevent plastic pipes of your drainage system

from being deformed.

■ The anti-unbalance device ensures that the

washing machine remains stable when

spinning.

A

Ecological hints

In order to obtain water and energy savings and

to protect the environment, we advice you to
follow these instructions:
■ Whenever possible, wash the maximum load

for the selected programme, without
overloading the drum.

■ Use a programme with prewash only for

heavy soiled items.

■ Measure out detergent according to the water

hardness, degree of soiling and quantity of
laundry being washed.

■ Select «Quick wash” for lightly soiled laundry.

^ Environment protection

■ Packaging recycling

Materials marked with the O symbol are
recyclable. To enable them to be recycled, they
must be placed in the appropriate collection

areas (or containers). Check with your local
authorities.

>PE<= polyethylene
>PS<= polystyrene
>PP<= polypropylene

■ Washing machine scrapping

When the appliance is to be scrapped, cut off the

power supply cable and make the door closing

device inoperative to avoid it becoming a death

trap for a child.

For correct disposal of the machine, contact your

local authority department which provides for

collection of urban solid refuse.

The symbols you will see on some paragraphs of this booklet have the following meaning:

A

I

A

Important information concerning the

safety in the use of your machine.

Disregarding this information might

lead to damages.

Information for correct use of your

machine and to obtain the best
performance.

Important information concerning

environment protection.

Our contribution to the protection of the

environment: we use recycled paper.

2

A

IMPORTANT INFORMATION

It is important that this instruction book be kept with the appliance for future reference. If you sell or

give the appliance away, make sure that the book is passed to the new owners so that they can

familiarise themselves with its operation and relevant warnings.

The following warnings are provided in the interests of overall safety. You must read them carefully

before installing or using the appliance.

Installation

■ When unpacking the appliance, check that it

is not damaged. If in doubt, do not use it and
contact the Service Centre.

■ All internal packing must be removed before

using the appliance. Serious damage may be
caused to the machine or adjacent furniture if

the protective transit devices are not

removed or are not completely removed.

Refer to the relevant paragraph in the

instruction book.

■ Any electrical work required to install this

appliance must be carried out by a qualified
electrician.

■ Any plumbing work required to install this

appliance must be carried out by a qualified
plumber.

■ After having installed the machine, check that

it is not standing on its electrical supply cable.

■ If the appliance is placed on a carpeted floor,

ensure that air can circulate freely between

the adjustable feet and the floor.

■ Use only the recommended quantities of

fabric softener. An excessive amount could
damage the laundry.

■ Leave the porthole door slightly ajar when

the appliance is not in use. This preserves
the door seal and prevents the formation of

musty smells.

■ Always check that water has emptied out

before opening the door. If not, drain the

water following the instructions in the

instruction book.

■ Always unplug the appliance and shut the

water tap after use.

Service/repair

■

In the event of a fault, do not attempt to

repair the appliance yourself. Repairs carried

out by inexperienced persons may cause
damage.

■ If repairs are needed, contact an authorised

service centre and ask for genuine spare

parts.

Use

This appliance is designed for domestic use.

It must not be used for purposes other than

those for which it was designed.

Do not overload the appliance. Follow the

instructions in the instruction book.

Only wash fabrics which are designed to be

machine washed. Follow the instructions on
each garment label.

Make sure that all pockets are empty.

Objects such as coins, safety pins, pins and

screws can cause extensive damage.

Do not machine wash garments saturated
with petroleum, methylated spirits,

trichlorethylene, etc. If such fluids have been

used to remove stains prior to washing, wait
until they have completely evaporated from

the fabric before placing garments in the

appliance.

Place small items such as socks, belts, etc. in

a cloth bag or pillowcase to prevent them
getting trapped between the drum and the tub.

Safety

■ This appliance is designed to be used by

adults. Children must not be allowed to touch
the controls or play with the product.

■ During high temperature wash cycles the

glass door becomes very hot. Do not touch it.

■ Pets sometimes climb into washing

machines. Check the drum before each use.

4

■

■

■

■

■

■

Description of the appliance, Detergent dispenser drawer and programme chart, Technical specifications

Страница 5

• Изображение
• Текст

DESCRIPTION OF THE APPLIANCE

1 Detergent dispenser drawer

2 Programme chart

3 Option buttons

4 Door opening button

5 Temperature selector dial

6 Operating pilot light

7 Programme selector dial
8 Adjustable feet

3 4 5 67

ir

B

,=Mi

ir

K

=”H

rh

□in :

/

Detergent dispenser drawer and
programme chart

Symbols

LU

Prewash

uu Main wash

Fabric softener

There is a programme guide in symbols on the

handle of the detergent dispenser drawer.

TECHNICAL SPECIFICATIONS

DIMENSIONS

Height

Width

Depth

85 cm

60 cm

32 cm

POWER SUPPLY VOLTAGE/FREQUENCY

TOTAL POWER ABSORBED

MINIMUM FUSE PROTECTION

220-230V/50 Hz

1750 W
10 A

WATER PRESSURE

Minimum
Maximum

5 N/cm

2

80 N/cm

2

MAXIMUM LOAD

Cotton

3 kg

Synthetics, delicate fabrics

1 kg

Woollens

0.7 kg

SPIN SPEED

700 rpm

C C This appliance complies with the following EEC Directives:

73/23/EEC of 19/02/73 relating to low voltage
89/336/EEC of 03/05/89 relating to electromagnetic compatibility

8

5

INSTALLATION

Unpacking

All transit bolts and packing must be

removed before using the appliance.

You are advised to keep all transit devices so
that they can be refitted if the machine ever has
to be transported again.

1. Using a spanner, unscrew and remove the

rear right-hand bolt and lay the machine on
its back, taking care not to squash the hoses.

This can be avoided by placing one of the

corner packing pieces between the machine
and the floor.

2. Release the two plastic bags by removing the

adhesive strip.

3. Carefully remove the right-hand bag (1) then

the left-hand bag (2) by pulling them towards
the centre of the machine.

4. Set the machine upright and remove the two

remaining bolts from the back.

5. Pull out the three plastic spacers from the

holes into which the bolts were fitted.

6. Plug the open holes with the plugs which you

will find in the plastic bag containing the

instruction booklet.

Positioning

Install the machine on a flat hard floor.

Make sure that air circulation around the
machine is not impeded by carpets, rugs etc.

Check that the machine does not touch the wall
or other kitchen units.
Carefully level by screwing the adjustable feet in
or out. Never place cardboard, wood or similar

materials under the machine to compensate for

any unevenness in the floor.

6

Water inlet, Water drainage, Electrical connection

Water drainage ■ electrical connection

• Изображение
• Текст

Water inlet

Connect the water inlet hose to a tap with a 3/4″

thread after having inserted the small filter «A”

supplied with the machine.

The other end of the inlet hose which connects
to the machine can be turned in any direction.

Simply loosen the fitting, rotate the hose and

retighten the fitting, making sure there are no

water leaks.

The inlet hose must not be lengthened. If it is
too short and you do not wish to move the tap,
you will have to purchase a new, longer hose

specially designed for this type of use.

Water drainage

The end of the drain hose can be positioned in
three ways:

Hooked over the edge of a sink using the
plastic hose guide supplied with the
machine. In this case, make sure the end

cannot come unhooked when the machine is
emptying.

This could be done by tying it to the tap with a

piece of string or attaching it to the wall.

In a sink drain pipe branch. This branch must
be above the trap so that the bend is at least

60 cm above the ground.

Directly into a drain pipe at a height of not
less than 60 cm and not more than 90 cm.

The end of the drain hose must always be
ventilated, i.e. the inside diameter of the drain

pipe must be larger than the outside diameter of

the drain hose.
The drain hose must not be kinked. Run it along
the floor; only the part near the drainage point

must be raised.

Electrical connection

This machine is designed to operate on a
220-230 V, single-phase, 50 Hz supply.

Check that your domestic electrical installation
can take the maximum load required (1.75 kW),
also taking into account any other appliances in

use.

Connect the machine to an earthed socket,

in accordance with current wiring regulations.

The manufacturer declines any

responsibility for damage or injury

through failure to comply with the above
safety precaution.

In the event of replacing the electric

cable, please contact our nearest
Service Centre.

7

Control panel, 1 spin speed reduction button, 2 half-load button l

3 anti-crease button u, 4 door opening button q-r, 5 temperature selector dial, 6 operating pilot light, 7 programme selector dial |oò

• Изображение
• Текст

USE

Control panel

1 Spin speed reduction button

By depressing this button the spin speed is

reduced from 700 to 500 rpm in the cotton
programmes and from 550 to 400 rpm in the

gentle programmes.

2 Half-load button l]^

By depressing this button when washing a small

load of cottons or linens (max 1.5 kg) you will

obtain a reduction of the water consumption on

the rinse cycle.
The machine will carry out 3 rinses instead of 4.

3 Anti-crease button U

By depressing this button on programmes H-J-

K-L-M the water of the last rinse is not emptied

out, to prevent the fabrics from creasing. To
drain the water, depress this button again (the

laundry will be gently spun) or select drain
programme «P”.

4 Door opening button

Q-r

Depress it to open the door.

5 Temperature selector dial

Turn this dial to select the washing temperature.

Position = cold wash.

6 Operating pilot light

This light is on whilst the machine is operating

and goes out at the end of the programme.

7 Programme selector dial |oò

To select the required programme, turn this dial

clockwise until the programme letter is exactly
opposite the pointer.

To start the programme, pull the dial outwards,
to switch off the machine, push the dial inwards.

8

Washing hints, Sorting the laundry, Temperatures

Before loading the laundry, Maximum loads, Laundry weights, Removing stains

• Изображение
• Текст

I

Washing hints

Sorting the laundry

Follow the wash code symbols on each garment
label and the manufacturer’s washing
instructions.

Sort the laundry as follows:

whites, coloureds, synthetics, delicates, woollens.

Temperatures

95°

60°

-)f (cold)

30°-40°

for normally soiled white cottons and

linen (e.g. tea cloths, towels,

tablecloths, sheets…)

for normally soiled, colour fast

garments (e.g. shirts, night dresses,
pyjamas….) in linen, cotton or
synthetic fibres and for lightly soiled

white cotton (e.g. underwear).

for delicate items (e.g. net curtains),

mixed laundry including synthetic

fibres and woollens bearing the label

«pure new wool, machine washable,
non-shrink»

Before loading the laundry

Never wash whites and coloureds together.

Whites may lose their «whiteness” in the wash.

New coloured items may run in the first wash;

they should therefore be washed separately the
first time.

Make sure that no metal objects are left in

the laundry (e.g. hair clips, safety pins, pins).

Button up pillowcases, close zip fasteners,
hooks and poppers. Tie any belts or long tapes.
Remove persistent stains before washing. Rub
particularly soiled areas with a special detergent

or detergent paste.

Treat curtains with special care. Remove hooks

or tie them up in a bag or net.

Maximum loads

Recommended loads are indicated in the
programme charts.

General rules:

cotton, linen: drum full but not too tightly

packed

synthetics: drum no more than half full

delicate fabrics and woollens: drum no more

than one third full.

Washing a maximum load makes the most

efficient use of water and energy.

For heavily soiled laundry, reduce the load size.

Laundry weights

The following weights are indicative:

bathrobe
napkin

quilt cover
sheet

pillow case

tablecloth
towelling towel
tea cloth

night dress
ladies’ briefs
man’s work shirt
man’s shirt
man’s pyjamas
blouse
men’s underpants

1200 g

100 g

700 g
500 g

200 g
250 g
200 g

100 g

200 g

100 g

600 g
200 g

500 g

100 g
100 g

Removing stains

Stubborn stains may not be removed by just

water and detergent. It is therefore advisable to

treat them prior to washing.

Blood: treat fresh stains with cold water. For

dried stains, soak overnight in water with a
special detergent then rub in the soap and

water.

Oil based paint: moisten with benzine stain

remover, lay the garment on a soft cloth and dab

the stain; treat several times.

Dried grease stains: moisten with turpentine,
lay the garment on a soft surface and dab the

stain with the fingertips and a cotton cloth.

Rust: oxalic acid dissolved in hot water or a rust
removing product used cold. Be careful with rust

stains which are not recent since the cellulose
structure will already have been damaged and

the fabric tends to hole.

Mould stains: treat with bleach, rinse well
(whites and fast coloureds only).

Grass: soap lightly and treat with bleach (whites
and fast coloureds only).

Ball point pen and glue: moisten with acetone
(*), lay the garment on a soft cloth and dab the

stain.

9

Detergents and additives, Quantity of detergent to be used

Страница 10

• Изображение
• Текст

Lipstick: moisten with acetone as above, then

treat stains with methylated spirits. Remove any

residual marks from white fabrics with bleach.

Red wine: soak in water and detergent, rinse

and treat with acetic or citric acid, then rinse.

Treat any residual marks with bleach.

Ink: depending on the type of ink, moisten the

fabric first with acetone (*), then with acetic acid;
treat any residual marks on white fabrics with

bleach and then rinse thoroughly.

Tar stains: first treat with stain remover,

methylated spirits or benzine, then rub with

detergent paste.

(*) do not use acetone on artificial silk

Detergents and additives

Good washing results also depend on the choice
of detergent and use of the correct quantities to
avoid waste and protect the environment.

Although biodegradable, detergents contain

substances which, in large quantities, can upset

the delicate balance of nature.
The choice of detergent will depend on the type

of fabric (delicates, woollens, cottons, etc.), the
colour, washing temperature and degree of
soiling.

All commonly available washing machine

detergents may be used in this appliance:

— powder detergents for all types of fabric,
— powder detergents for delicate fabrics (60°C

max) and woollens,

— liquid detergents, preferably for low

temperature wash programmes (60°C max)
for all types of fabric, or special for woollens
only.

The detergent and any additives must be placed

in the appropriate compartments of the

dispenser drawer before starting the wash

programme.

If using concentrated powder or liquid

detergents, a programme without prewash must

be selected.

Pour liquid detergent into the dispenser drawer

compartment marked |

m

J just before starting

the programme.
Any fabric softener or starching additives must

be poured into the compartment marked
before starting the wash programme.

Follow the product manufacturer’s

recommendations on quantities to use.

Quantity of detergent to be used

The type and quantity of detergent will depend

on the type of fabric, load size, degree of soiling
and hardness of the water used.

Water hardness is classified in so-called

«degrees” of hardness. Information on hardness
of the water in your area can be obtained from

the relevant water supply company, or from your

local authority.

Follow the product manufacturers’ instructions

on quantities to use.

Use less detergent if:

— you are washing a small load
— the laundry is lightly soiled
— large amounts of foam form during washing.

Degrees of water hardness

Level

Characteristic

Degrees

German

°dH

French

°T.H.

1

soft

0- 7

0-15

2

medium

8-14

16-25

3

hard

15-21

26-37

4

very hard

more than 21

more than 37

10

Комментарии